Hurry maya2012 can open files in 2011 prompts what happens when it is corrupted

The 2012 version is higher than the 2011 version, and the lower version can't directly open the MB file of the higher version.

If you have to open it, try clicking on the small square (i.e. the property settings) behind the "open sence" command and ticking it in the pop-up window"ignore version"(Ignore Version).

But I remember that generally the lower version can't open the higher version, especially the special effect class, and the higher version has a lot of functions or parameters that the lower version doesn't have. If it's a model, it can be opened or guided

Also, maybe you made this file in 2011, but opened it in 2012 and modified and saved, then it will become a 2012 version of the file, and 2011 cannot be opened directly.

So if you're in a hurry to solve the problem, you can only install a 2012.

If you make a mistake, ask someone else for advice. Hope to be able to help the landlord.

What version of the original file was made? Did you save it again in 2012? English prompt scene file is missing.

If it has been saved once in 2012, you need to check the Ignore Version in the settings after Open Scene before opening it in 2011. to open a file saved by a higher version.

2012 is higher than the 2011 version, and the compatibility is not good, ma often opens errors, loss of materials or something.

You can use maya2012 to save it in ma format first,Open it with 2011 and check the version of the law in the open option,If it doesn't work,Open it with text format,A few maya2012 at the beginning of the bit2011 can be saved under it,That's what I did before,I hope it can help you!

Hello friends;

Maya: I didn't pretend.

However, the software can not be installed but often encountered, sometimes the system can not be installed and the software can not be installed in general, there are several situations:

a There are not enough disks.

b Unzip the wrong password.

c There are requirements for the installation path.

d Source files are missing.

e The system does not meet the software requirements.

I think you'll check it yourself, and it's better to change your outfit.

It could be a version issue. This can happen in different versions of different documents.

Solution: Step 1: Find any undamaged file to open Word, in Tools - Options - General, check "Confirm conversion when opening".

Step 2: Click on File - Open in the upper left corner of the word software, find the path of the file you have corrupted, click on it with your mouse, note that it is a click, not a double click. Then you will find a black triangle inside the red box on the right.

Step 3: Click on the triangle and click "Open & Repair" in the pop-up menu.

System file corruption, run chkdsk, is to check and repair the wrong system file, run the test in the run box, it is estimated that you have not gone through disk defragmentation for a long time, it is recommended to go through disk defragmentation and defragmentation every 2 months, reduce system errors, and improve the system speed.

If that doesn't work, reinstall the 360 browser.

How did you solve it??

Hello, there is only one.

Is this the case for the files or is this the case for all PDFs? If it's just one, then it's that file that is corrupted.

If all of this is the case, there is probably a problem with the PDF reader on your computer. You can reinstall the old PDF reading software again, if it still doesn't work, you can change to another PDF software to try, such as "Fuxi PDF FoxitReader", people feel good, better than Adobe Reader. Good luck!

I also encountered the same situation, and the previous project could not be opened.

Something like that? If you lead this, it's normal.

This basically can't be repaired, this should be your file has been corrupted, so you can only do this, there is no way to do it.

Dear, you first save the 12 version of the file in ma format, and then open the file with Notepad, change the first few 2012 at the beginning of the file to 2011, and then open 2011 and drag it in.

If dragging doesn't work, use the Open File command and check Ignore Version. Hope.

Open the setting on the right side of the scene, there seems to be an ignore version in it, I don't know if you can try it.

Windows---Setting Preferences--- Plug-in Manager's obj exprot, tick it, and export it in obj format.

Menu windows--settings preferences--plug-in manager, open the plugin manager, tick the options (tick both), and you can grind to export the beam with export.