5A05 Aluminum Plate Chemical Composition Uses Xingpuli Aluminum has complete specifications 0510 830

Updated on healthy 2024-08-12
7 answers
  1. Anonymous users2024-02-16

    The processing cost of 5A05 aluminum plate is 20000 T Southwest Aluminum, 5A05 characteristics:

    Al-MN alloy is the most widely used anti-rust aluminum, this alloy has high strength, especially fatigue strength: high plasticity and corrosion resistance, can not be strengthened by heat treatment, good plasticity when semi-cold work hardening, low plasticity during cold work hardening, good corrosion resistance, good weldability, poor machinability, polishing.

    5A05 Chemical Composition:

    Aluminum AL: Margin Silicon SI: Anti-rust Aluminum 5A05

    Copper Cu : Magnesium Mg: Zinc Zn: Manganese Mn: Iron Fe: Note: Single: ; Total:

    5A05 Mechanical Properties:

    Tensile Strength b (MPa): 225 Conditional Yield Strength MPa): 110 Elongation δ10 (15

    5A05 is mainly used for low-load parts that require high plasticity and good weldability, working in liquid or gaseous media, such as mailboxes, gasoline or lubricating oil conduits, various liquid containers and other small load parts made of deep drawing: wire rods are used to make rivets.

    5A05 corresponds to the old grade LF5

    The production area is mainly Southwest Aluminum and East Light Aluminum.

  2. Anonymous users2024-02-15

    5A05 corresponds to the old grade LF5, and the German grade: ALMG5

  3. Anonymous users2024-02-14

    5A05 belongs to anti-rust aluminum alloy, also known as aluminum-magnesium alloy, ALMG5 alloy, corresponding to the old brand LF5

    It is the most widely used anti-rust aluminum, this alloy has high strength, especially fatigue strength: high plasticity and corrosion resistance, can not be strengthened by heat treatment, good plasticity when semi-cold work hardening, low plasticity during cold work hardening, good corrosion resistance, good weldability, poor machinability, can be polished.

  4. Anonymous users2024-02-13

    5A05 is an Al-MG anti-rust aluminum alloy, which cannot be strengthened by heat treatment. The alloy has a higher magnesium content and lower strength, which is similar to that of alloy 5A03. Cold deformation of the alloy can increase the strength but reduce the plasticity.

    The plasticity in the annealed state is high, and the plasticity in the semi-cooled work hardening state is acceptable. The corrosion resistance of the alloy is good, and the weldability is acceptable, and it is suitable for spot welding, atomic hydrogen welding, gas welding, and argon arc welding. Its machinability and annealing state are very poor, and the semi-cold work hardening state is good.

    Alloy 5A05 is commonly used in the manufacture of welded pipes, welded oil tanks and other liquid containers, and other parts that require high process plasticity, good corrosion resistance, and moderate loads; Wire rods are used as welding rods and rivets, which need to be anodized. In foreign countries, similar alloys (such as 5456) are used to make armor plates and high-strength structural parts. Storage tanks, pressure vessels, and marine components.

    Mechanical properties: tensile strength b (mpa): 225

    Conditional yield strength mpa): 110

    Elongation δ10 (%15

  5. Anonymous users2024-02-12

    5005 aluminum plate is often used as conductors, cookware, instrument panels, shells and building decorations, building materials and interior and exterior materials, vehicle interior materials, etc. Its chemical composition can be precisely determined using femtosecond detection technology. In general.

    Aluminum AL: Margin Silicon Si : Copper Cu : Magnesium Mg: Zinc Zn:

    Manganese Mn: Chromium Cr: Iron Fe:

    Its performance is: Tensile strength b (mpa): 100 205 elongation δ10 (%1 8

    The annealing temperature is: 345

    The strength of 5005 aluminum plate and strip is comparable to that of 3003, and the weldability and machinability are good5005 aluminum plate is similar to that of 3003 alloy, with medium strength and good corrosion resistance. The anodized film is brighter than the oxide film on alloy 3003 and harmonizes with the hue of alloy 6063.

  6. Anonymous users2024-02-11

    Chemical Composition: Silicon Si:

    Iron fe: copper mu empty base Xun Jin cu:

    Manganese magnesium mg:zinc zn:

    Al: The margin is stupid.

    Other: Single: Total:

  7. Anonymous users2024-02-10

    5A05 aluminum plate is Al-MG aluminum alloy, the strength is equivalent to 5A03, heat treatment can not be strengthened; High plasticity in annealing state, medium plasticity in semi-cold hardening; 5A05 aluminum plate has good welding performance when it is welded with hydrogen atoms, spot welding, gas welding, and argon arc welding; High corrosion resistance, poor machinability in annealing state, good machinability during semi-cold work hardening, anodizing treatment is required when manufacturing rivets.

Related questions
6 answers2024-08-12

I don't know if you're asking about paint. The main components of paint include the following five parts: >>>More

10 answers2024-08-12

Bone organic matter and inorganic matter constitute the main components of organic matter are collagen fibers, five-year protein and grain vermilion pine bone number five accumulation evil friends called bone salt, the main components are, calcium phosphate and calcium carbonate.

5 answers2024-08-12

Oxygen is a kind of elemental formed by oxygen, the chemical formula O2, its chemical properties are relatively active, and most elements can react with oxygen. It is not very active at room temperature, and it is not easy to interact with many substances. However, it is very active at high temperatures and can be directly combined with a variety of elements, which is related to the electronegativity of oxygen atoms second only to fluorine. >>>More

14 answers2024-08-12

The effects of acetic acid pretreatment on the main chemical components and enzymatic hydrolysis saccharification efficiency of rice straw were studied. The straw was treated with different acetic acid dosages (0 4%) at 160, and the klason lignin content of the straw remained basically unchanged after pretreatment, and about 60% of the acid-soluble lignin was removed. The ash content (mass fraction) is reduced by about 30%, and almost all of the SiO2 in the ash content is retained in the pretreated slurry. The increase of the amount of acetic acid in the pretreatment had no significant effect on the changes of acid-soluble lignin and ash content. >>>More

10 answers2024-08-12

SUS410L has a lower carbon content than 410S, good bending of welded parts, good processing performance, and good high temperature oxidation resistance. >>>More