The home is underfloor heating, do you have any requirements for the floor when decorating?

Home decoration and installation of floor heating, most of them think that laying floor tiles is the best, the floor is not very suitable, in fact, it is not, but as a more complex system engineering, there are certain requirements for the laying of the floor.

1. Before laying, in order to avoid damaging the heat dissipation coil, the construction method is not allowed to destroy the surface.

2. Heat and deliver water to the floor heating system, and the water temperature is at least 50 to ensure the normal operation of the floor heating system, and continue to heat preservation for more than 12 hours.

3. Check whether the ground is kept clean, tidy and dry, whether the gap between the door and the ground meets the demand, and whether there is leakage in related facilities.

4. When the laying season is a relatively cold season, in order to reduce the possibility of floor deformation, the floor should be placed on the site in advance to adapt to the temperature difference change on the site.

1. Lay the special mat neatly on the ground and seal it with self-adhesive tape at the interface.

2. The direction of floor laying should be proportional to the light of the room, when installing the first row, the long side groove is towards the wall, put the wooden wedge between the floor and the wall, and ensure that the floor has 8-12mm expansion and contraction gaps, and the floor between the rows should be installed in staggered joints, and the distance between the staggered joints is not less than 20cm.

3. Observe the height difference, gaps and other defects on the surface of the floor, and only after meeting the requirements can the sizing be spliced, and the excess glue remaining on the surface of the floor should be cleaned up in time while sizing.

4. If the interface between the room, the living room, the corridor, etc., or the length of the floor is greater than 8m, in order to reduce the arching phenomenon of the floor, the floor needs to be cut off, leaving an expansion joint of 8-12mm, and connecting it with a closing strip.

After laying

The time for people on the floor should be 12 hours after it has been laid, but the follow-up work should be carried out after 24 hours.

In winter, heating is very important, and floor heating is the most comfortable way to heat, when choosing floor heating, you should pay attention to the choice of flooring.

Floor heating generally does not use solid wood flooring, laminate flooring, or solid wood flooring, mainly solid wood flooring will be dry and deformed after being baked by floor heating, arching, and reduced moisture content. In addition, the thermal conductivity of wood is relatively poor, which affects the heat dissipation of floor heating.

Floor heating belongs to low-temperature radiant heating, the heating water temperature is about 40-50 degrees, and there is a concrete protective layer above the floor heating pipe, so the temperature of the ground is about 30 degrees. If you lay a solid wood floor with a wooden keel, the worse the thermal conductivity.

Therefore, in order to have a better heating effect, the floor heating room generally does not use wooden floors or uses less, and it is best to use ceramic tiles. Or with electric underfloor heating laid under the wooden floor. The type of floor can choose laminate flooring, because the stability of this kind of floor is relatively good, made of wood-based panels, it is not easy to be deformed and cracked by heating, and the disadvantage is environmental protection, and it is easy to release harmful substances such as formaldehyde at high temperatures.

1. The floor is stable in size and can withstand temperature changes without damage.

2. No deformation and cracking, and the coefficient of thermal expansion and contraction is small.

3. Environmental protection, no formaldehyde and harmful gas release.

4. Don't be afraid of soaking the floor with water (prevent the floor heating pipe from being damaged, the water from flowing out, and the floor from being damaged).

If there is floor heating, you must choose those materials that are resistant to high temperature and are not easy to deform when installing the floor, if you choose the ordinary one, it is easy to cause thermal expansion and cold contraction of the floor cracking, and the maintenance cost will be more.

It is better to choose marble flooring because marble flooring is not only beautiful but also conducts heat well.

Generally, the solid wood floor has a good thermal insulation effect, and then the teak floor is more environmentally friendly, which is also good, and there is the laminate floor, which is also called multi-layer laminate flooring, which has good wear resistance and deformation resistance.

In terms of thermal conductivity, natural stone is better, then ceramic tiles, followed by composite wood flooring, and solid wood flooring is less effective. So you can often hear people complaining in communities with poor heating that wooden floor rooms are not as warm as tile rooms, and wood floor homes are not as warm as tile homes.

You can choose the floor heating floor, you can also choose the three-layer solid wood floor of the icon, and I personally prefer to choose the three-layer solid wood floor.

At present, in line with the above standards, there are three types of commonly used floor heating floors: ceramic tiles (marble), composite wood floors, laminate floors, solid wood floors have good thermal insulation effect, but the use of solid wood floors for floor heating is more ideal, and the production and manufacturing of solid wood floors uses special adhesives for floors, which have high waterproofness and aging resistance