After the HP laptop is turned on, the WLAN turns on slowly, and it takes 1 to 2 minutes before you c

The way you get the IP is to get it dynamically, and you can set a fixed IP to see. And your computer has just turned on a lot of things to load, if your hardware is not hard enough, it will definitely be slow, and the system that does not need to be booted and started is banned!

You just change the IP. Click on the computer icon in the lower right corner, in the attribute column, there is an IP protocol in it, double-click. It's good to change the IP address to a fixed one.

It's that you have too many startup projects ... At the same time, HP's installation of win7 is not very suitable.,I've also installed it.,The response is much slower.。 It is recommended to have a deep one, this one is good.

Normal HP is so slow, the association is very fast, generally within 10 seconds, HP has no way, I have been fooled.

1 Hello all:

Hello, it is recommended that you do a factory reset and set up your router as follows:

1. Connect the home network cable to the WAN port of the router.

2. Use another network cable to connect to your computer at one end, and connect to your routing LAN port at the other end, (LAN port is the interface marked on the route!) ）

3. Turn on the computer, open the browser, and enter the route login IP in the address bar

4. Enter the routing login account and password in the pop-up dialog box, friendly reminder, if you don't know the routing login IP, login account and password, you can turn the route over and take a look, and write it on the back of the route! (Generally username: admin, password:.)

admin）

5. After entering the routing setting interface, the quick setting interface will generally pop up, you can select the broadband dialing method in this interface, PPPOE, and enter the Internet account and password!

6. Find the wireless settings, set your wireless SSID, wireless password, and wireless channel.

7. After the settings are completed, save the exit and restart the route! Once the routing restart is complete, your routing hardware connection and setup are complete! In addition, there is another point to remind that if your home is a ** line and there is a cat, it is recommended that you turn off the power of the cat when you set the route, and when the route is set up, turn on the power of the cat!

For details, please see this post.

If so, no network access.

We recommend that you try a few of the methods in this post.

If it still doesn't work, please keep asking.

Hope your problem is solved soon! Thank you

1.First of all, you need to refer to the manual of the router to set up the router;

2.Then turn on the wireless network card switch of the notebook when the wireless network card is installed and the number of drivers is fast (the wireless network card switch is above the keyboard or in front of the notebook ((|.)Logo) - when the wireless network card switch is turned on, the indicator light is usually white or blue; When the wireless adapter is turned off, the indicator light is usually orange or not lit.

3.Left-click on the network icon in the lower right corner of the desktop to open the network list and connect to the network signal without a balance line.

How to find the official driver or software of HP products:

1.Log in to HP Official**:

4.Select the operating system installed on the notebook and click "Next".

Hello,I'm hp monopoly,You this question,You can check whether your network card switch is turned on or off,This switch is designed for power saving,First of all, thank you very much for choosing our HP's book,And then we say your book,If the switch is normal,You look at the "Internet Neighbor" attribute in this deactivated device is not displayed deactivated,Yes,Right click to use it,

You're a DV2000 6000 3000 series. It can be turned off with hardware. The switch is on the laptop, and the touchpad is about 5 to the left, and there's a switch there, and the DV3000 series is on the top of the touch control.

This is the method of hardware shutdown.

...Right-click on My Computer - Properties - Hardware - Device Manager.

The line of the network card will be x.

You just hit start.

Is there a switch that you turned off? HP has a WLAN switch. In order to save power, in addition to preventing interference with other wireless devices.

Turn on via the control panel.

Click on the Start button in the bottom left corner of the screen and select "Control Panel".

In the Control Panel, click Network & Internet.

In Network & Internet, click Network and Sharing Center.

In the Network and Sharing Center, click Change adapter settings.

In "Change Adapter Settings", find "Wireless Network" and right-click and click Enable.

One is that the wireless network card driver is not installed, and the other is that the shortcut key driver is not installed, install a driver wizard or driver life, update your two drivers.