How do I make every computer in my LAN have to dial up to access the Internet? How do I set it up?

1.Use a switch.

2. If each client has its own external network and password, then the router should be set to "switch mode" or simply replace the router with a switch, so that the client can use its own external network and password to achieve dial-up Internet access.

The router is set to a "switch" by physically connecting the network cable to the non-WAN port of the router and connecting the client to the LAN port of the router. Then turn off the router's DHCP service and you're done!

3. Find an old computer (386 or more) and make it into a soft router, such as ROS, X-Router, Sea Spider, etc., all of which provide PPPoE services, and DIY's own router is very practical!

Routing is critical and can't be swapped out

Upstairs said yes If you want to implement management, you can directly use network management software It is recommended to use network law enforcement, or network scissorhands. . . These software are powerful, and.

You can control the Internet access rights of all computers in the local area network.

No, you can unplug the network cable between the switch and the computer, and plug in the corresponding network cable if you want to go online.

No, but you can set up manual login on the switch**.

This one is very simple, just replace the router.

No, you can't.

If you want to manage other computers to access the Internet or not. You can go to the next Jusheng network management software.

Put it with a VPN.

Find some tutorials for specifics.

The steps to set up your computer to manually dial up the Internet are as follows:

1. The modem is connected to the home broadband cable, connected to the host network card through the twisted pair cable, and the host is turned on to enter the system. Click the taskbar network icon, and then tap Open Network & Sharing Center.

2. Click to set up a new connection and network; Click Connect to the Internet and click Next.

3. Click on Broadband (PPPoE).

4. Enter the broadband account password, click to connect, and then you need to connect to the Internet, you need to click on the broadband connection first.

Extended information: There is no strict definition of broadband. From a general point of view, it is the bandwidth that can meet the needs of various ** transmission on the network that people can feel, so it is also a dynamic and developing concept.

On January 7, 2015, the Federal Communications Commission (FCC) made its annual broadband progress report, in which the current chairman, Tom Wheeler, redefined "broadband".

The original downlink speed of 4 Mbps was adjusted to 25 Mbps, and the original uplink speed of 1 Mbps was adjusted to 3 Mbps. The new standard for broadband networks in the United States: 25Mbps downlink and 3Mbps uplink.

Take win7 as an example, the steps are as follows:

1. The modem is connected to the home broadband cable and connected to the host network card through the twisted pair cable;

2. Turn on the host and enter the system;

6. Click Broadband (PPPOE);

7. Enter the broadband account password and click to connect.

In the future, if you need to connect to the Internet, you need to click on the broadband connection first.

Just uncheck the auto-dial connection.

1. Open the Start Menu on your desktop, and then, select Control Panel to open.

2. After entering the control panel options, click on Internet Options and click on Enter.

3. Then in the Internet options settings, find the option to connect and click Open.

4. Then check the box in front of the automatic dial-up connection as shown in the figure below to complete the setting.

5. Note that the path of dial-up connection can be through the default broadband, and click OK to take effect after confirmation.

6. If you do not set up automatic dialing, you can click the broadband connection icon to manually connect to the Internet.

Telecommunications. Create a new manual connection.

Buy a wireless router and follow the steps in the manual to set it up on the dial-up computer It's very simple.

Telecom has that Wuxi cat, you buy a desktop dial-up notebook and use wireless dial-up!

Is it a wireless computer that uses a broadband connection to access the Internet?

Depending on your computer's operating system, the steps in setting up dialing may vary, but they are generally the same.

1.Click the small arrow to the right of the taskbar, right-click the PC icon, and select Open Network & Sharing Center.

2.Click on "Set up a new connection or network" and then click on "Connect to the Internet" to go to the next step.

3.Click"No, create a new connection" and then click Next"Broadband (PPPoE) (R)."。

5.Finally, enter the broadband account on the right side of the user name, enter the password in the next line, click to remember this password (the next time you turn on the computer, you don't need to enter the password to connect directly), and then click on the connection.

Open the browser, Tools, Internet Options, Connections, Add, Over Broadband, and fill in the account password.

Online Neighbors View Network Connections Create a New Connection Next Connect to the Internet Next Set up my connection manually Next Connect with a broadband connection that requires a username and password Name whatever you want Fill in your broadband connection account.

1.Network architecture: ADSL** line - > modem - > router - > client.

2.If the ** line and the cat are in your room, use (1), but set the Internet account password in the route.

3.If it is a network cable pulled directly (non-** line, the cat is at the landlord's house), the network cable pulled by the landlord and the network cable of the client are connected to the routing LAN port (turn off the routing DHCP), and the client automatically obtains the IP address.

4.See if IE is enabled**.

5.If there are restrictions on the landlord's side, it doesn't matter, set the IP and MAC addresses of computers that can access the Internet to the routing WAN.

Broadband Internet access requires ADSL users and passwords, first of all, connect the network cable port of the 1-other numbers of the route to the computer, set the IP of the same section as the routing on the computer, and then log in to the route, and enter the ADSL account and password into the route. And it's set to connect automatically. After that, connect the network cable of the broadband modem to the router.

The other 1-other ports of the route are connected to the computer, you can go to the Internet, if you can't get on the Internet, you can restart the routing and broadband modem.