AutoCAD2018 installation is unsuccessful, ask for help

I just installed the CAD2018 version, there are no special requirements, unzip after the online **, and then exit the antivirus software, and install it. After the installation is successful, crack, remember to disconnect the network here. If your installation is unsuccessful, be sure to clean up the installed information on your computer before installing.

Otherwise, how you reinstall it will be redundant. In the end, it still couldn't be installed. AutoCAD2018 installation is unsuccessful, ask for help.

CAD2018 cannot be installed and the reasons and solutions

CAD installation attentionCAD is a professional drawing software, we can often hear about CAD, CAD drawing and other words in daily life, the CAD here is a software used for architecture, machinery, interior design and other product construction and electronic product structure design, has been widely used in various fields.

The XP system defaults to a 32-bit system, and it is recommended to install the CAD version between 08 and 10. The W7 system is divided into 32-bit system and 64-bit system, and it is recommended to install version 08-17. W8 or W10 system is divided into 32-bit system and 64-bit system, it is recommended to install version 14 or 17 version (the installation of lower versions is prone to errors, it is recommended not to install versions below 08, the installation success rate is low).

When installing Visual 2010, we found that a critical error occurred during installation.

After opening it, we can see that there is an x86 visual 2010 on the computer, and there is no x64 visual 2010.

The next thing we can do is to reinstall Visual 2010 x64. The installation is complete. Finally, we can restart the installation of AutoCAD 2018. At this point, the installation should be completed smoothly.

To install the CAD, pay attention to the following issues:

On the installation start screen, you need to agree to the [Agreement] before you can proceed to the next step.

If you have installed this version and uninstalled it incorrectly, you must uninstall CAD in the computer system (uninstall or change the program), and do not use other methods. This version can't be installed, and you need to change the CAD version.

If you don't have enough space on the installation disk, you can't install it.

When installing, click [Try 30-day installation].

If the computer configuration is not good, this product cannot be installed.

Explain the installation process in detail to find out why it can't be installed.

Then completely uninstall and clean up, please reply to the post below for details to see how Autodesk products are installed or uninstalled normally and how to solve the situation where the Autodesk product cannot be installed or uninstalled, the installation or uninstallation is not normal, etc.

If you don't understand or can't operate, you can use this tool to uninstall.

Autodesk's dedicated installation check and uninstall tool.

If you have one, clean up the registry before attempting to install it.

Detailed installation tutorial:

Since the CAD is not uninstalled, it is caused in a hurry.

1. Try to uninstall CAD in the control panel;

2. If it is unsuccessful, find the CAD installation path, and then delete all the files related to CAD;

3. Then clean up the registry (the registry option is generally turned on by default, and you can use security software to clean up the computer junk);

4. It is best to try to install CAD, and it is best to run it as an administrator;

Generally, if the CAD installation is not successful, there will be an installation failure log, pay attention to check it, it will help solve the problem quickly!

The above is personal experience, if you still can't solve it, @私信 willing to solve the problem!

Answer 1: Win+R opens the registry and enters regeditRelated tutorials: Which win key is it? Win10 system under the use of the win key 2 in the search for "cad2018" in the search for the following file, think carefully should be a registry problem, other versions should also refer to this method, and then delete the folder starting with fee98bb.

3. Close the registry and restart the computer. The installation is successful in one pass.

I didn't change the folder, and this problem also occurs. Here's how I got it.

1.Click Start, enter the control panel, click Programs & Functions, uninstall Autodesk AutoCAD 2018 Chinese Simplified (simplified Chinese), only uninstall the Bidou arrow in the figure below, do not uninstall anything else.

If when uninstalling, error 1327 appears, the drive is invalid, then click Start, Run, enter subst d: %temp%, click OK, and then you can uninstall, as shown below.

2.After the uninstallation is completed, it will be installed once and you will be fine. If the installation has error 1327 and the drive is invalid, then click Start, run this finch, enter subst d: %temp%, click OK, and then the installation can be early.

It is caused by the incompatibility of CAD software, and the solution is as follows:

1. First of all, in the computer, find the icon of the CAD software, as shown in the figure below.

2. Then right-click the mouse and find the properties in the right-click menu bar, as shown in the figure below.

3. Enter the property setting dialog box, as shown in the figure below.

4. Then in this property window, find the compatibility, as shown in the figure below.

5. Then check "Run this program in compatibility mode" and "Run this program as administrator", click OK, and then start CAD to open it.

Summary. Hello, I'm glad to help you answer --1First, on your computer, find the CAD software icon.

2.Then right-click and find Properties in the right-click menu bar.

3.Enter the property settings dialog.

4.Then in this properties window, find the compatibility.

5. Then check "Run this program in compatibility mode" and "Run this program as administrator", click OK, and then start CAD to open it. Hope it helps, my dear

I can't open the software after installing CAD2018, what should I do if this appears?

Hello, please wait! We are inquiring about you and will reply to you immediately!

Hello, I'm glad to help you answer --1First, on your computer, find the CAD software icon. 2.

Then right-click and find Properties in the right-click menu bar. 3.Enter the property settings dialog.

4.Then in this properties window, find the compatibility. 5. Then check "Run this program in compatibility mode" and "Run this program as administrator", click OK, and then start CAD to open it.

Hope it helps, my dear

Hello, if you are satisfied, please use your noble hands to point a [like], your small gesture is very important to us, please raise your noble hand, to add a momentum, thank you.

Summary. Hello, Xiao Du is honored to help you answer.

1.First, on your computer, find the CAD software icon.

2.Then right-click and find Properties in the right-click menu bar.

3.Enter the property settings dialog.

4.Then in this properties window, find the compatibility.

5. Then check "Run this program in compatibility mode" and "Run this program as administrator", and finally start CAD!

Hope it helps, thank you for your consultation!

I can't open the software after installing CAD2018, what should I do if this appears?

Hello, Xiao Du is honored to help you answer 1First, on your computer, find the CAD software icon. 2.

Then right-click and find Properties in the right-click menu bar. 3.Enter the property settings dialog.

4.Then in this properties window, find the compatibility. 5. Then check "Run this program in compatibility mode" and "Run this program as administrator", and finally start CAD!

Hope it helps, thank you for your consultation!

Still can't do it.

Is the CAD2018 software installed by Pro genuine? Genuine version needs to buy a key to activate the use of Oh, self-learning network has an activated version of CAD2018, the file has detailed installation steps.

I know how to activate it, and now it's installed, and it can't be opened.

That's uninstalling, reinstalling.

The registry uninstall of the previous CAD version is not clean, you want to uninstall CAD as well as Microsoft.NET Framework all versions, then reinstall.

I didn't change the folder, and this problem also occurs. Here's how I got it.

1.Click Start, enter the control panel, click Programs & Functions, uninstall Autodesk AutoCAD 2018 Chinese Simplified (simplified Chinese), only uninstall the arrow pointed to in the figure below, do not uninstall anything else.

If when uninstalling, error 1327 appears, the drive is invalid, then click Start, Run, enter subst d: %temp%, click OK, and then you can uninstall, as shown below.

2.After the uninstallation is completed, it will be installed once and you will be fine. If the installation has error 1327 and the drive is invalid, then click Start, Run, enter subst d: %temp%, click OK, and then install it.