What to do if the win10 computer always restarts automatically

If you have installed hardware and connected to other devices, you can change the software version or run it in compatibility mode, reinstall the corresponding driver provided by the ASUS official website, and restore the pre-installed system to try. If the fault persists, it is recommended to go to the service center for testing.

The automatic restart of the computer has little to do with the win10 system, unless the installed win10 system is not genuine;

The reason why the computer will automatically restart when it is turned on;

The computer runs a lot of software, and the CPU's CPU is not good, which causes the temperature of the computer parts to overheat, such as the CPU and graphics card, which will be overheated, and the temperature will be shut down or restarted if the temperature is too high.

2. Computer poisoning.

That's what happened.

3,Win10 system is not genuine.

Workaround;

1. In the case of overheating, only turn off the computer to rest and play, and you can change the CPU and fan to increase the speed of the fan, which can cool down.

2. Computer poisoning, only antivirus, because the computer can not be turned on, only restart the computer into the safe mode of the computer to find the computer's antivirus software full antivirus, and finally restart the computer on it, because the computer is poisoned, it means that the antivirus software on the computer can not prevent viruses, you can change to a software that can prevent viruses, such as Tencent Computer Manager, Norton, Kaspersky, Oriental Micropoint and other famous antivirus software.

3. The problem of the computer system, this situation can only be reinstalled by reinstalling the system, and you will not install the system, you can directly find the help of the personnel who repair the computer and install the regular version of the system.

The computer always restarts automatically.

Control Panel --- System and Security --- System - Advanced System Settings

Once the System Properties window opens, switch to the Advanced tab and click the Settings button in the Enable and Failback column.

From the "Startup and Fault Recovery" window that opens, clear the "Automatic Restart" item in the "System Failure" column, and click "OK" to complete the setting.

From the "Run" window that opens, enter "msconfig" and press enter to enter the main interface of the system configuration utility.

In the "System Settings" interface, switch to the "General" tab, check the "Diagnostic Startup" item, and click the "OK" button to restart the computer.

When the system reboot is completed, enter the "System Configuration" interface again, switch to the "Services" tab, check the "Hide Windows Services" item, and check the item you want to start automatically with the system, and click "OK" to complete.

If the above methods still do not solve the problem of automatic restart of the computer, make the following settings:

Enter the "Control Panel" - "Power Options" interface in turn, and click the "Select the function of the power button" button on the left side.

Finally, in the "System Settings" interface, clear the "Enable Fast Startup" item from the "Shutdown Settings" column, and click the "Save Modifications" button.

There are generally the following reasons for this situation:

1. It may be that there is an incompatibility between the system or programs, press F8 to move to the advanced option when you boot up, and select "The latest correct configuration" to enter the repair, and it is not possible to press F8 to enter the safe mode to restore the system or reinstall the system.

2. The CPU or other hardware temperature is too high, and the memory and graphics card are incompatible or faulty.

3. If the hard disk has bad sectors, please use the system's built-in functions or software to repair the disk, or format the hard disk to repartition and reinstall the system.

4. Change the default automatic restart of the system: right-click on My Computer Properties Advanced Settings in Startup and Failure Recovery Remove the check mark before "Auto Restart" in System Failure, and then press OK and Apply to restart the computer.

Causes and solutions for win10 computer automatic restart:

Reboot Cause: The cause of this problem is usually caused by incompatible hardware.

Solution: 1. Find the "This PC" icon on the desktop, right-click and select "Properties" from the pop-up right-click menu.

2. After opening the window, find the "Advanced System Settings" button on the left side and click to enter the detailed settings interface.

3. After opening the "System Properties" window, switch to the "Advanced" tab and click the "Settings" button in the "Enable and Failback" column.

4. From the "Startup and Fault Recovery" window that opens, clear the "Auto Restart" item in the "System Failure" column, and click "OK" to complete the setting.

5. If the problem of automatic system restart cannot be solved after passing the above settings, you need to make the following settings:

Use "win+r" to open the "Run" window, enter "msconfig" and press enter to enter the main interface of the system configuration utility.

In the "System Settings" interface, switch to the "General" tab, check the "Diagnostic Startup" item, and click the "OK" button to restart the computer.

When the system reboot is completed, enter the "System Configuration" interface again, switch to the "Services" tab, check the "Hide Windows Services" item, and check the item you want to start automatically with the system, and click "OK" to complete.

Click on the Win10 official version of the desktop to find the "This Computer" icon, right-click and select the "Properties" item from the pop-up right-click menu.

At this time, the "Control" window will open, find the "Advanced System Settings" button on the left side and click to enter the detailed settings interface.

Once the System Properties window opens, switch to the Advanced tab and click the Settings button in the Enable and Failback section.

From the "Startup and Fault Recovery" window that opens, clear the "Automatic Restart" item in the "System Failure" column, and click "OK" to complete the setting.

If the problem of automatic system restart cannot be solved after the above settings, then we need to make the following settings: use "win+r" to open the "run" window, enter "msconfig" and press enter to enter the main interface of the system configuration utility.

In the "System Settings" interface, switch to the "General" tab, check the "Diagnostic Startup" item, and click the "OK" button to restart the computer.

When the system reboot is complete, enter again. Click on the Win10 official version of the desktop to find the "This Computer" icon, right-click and select the "Properties" item from the pop-up right-click menu.

At this time, the "Control" window will open, find the "Advanced System Settings" button on the left side and click to enter the detailed settings interface.

Once the System Properties window opens, switch to the Advanced tab and click the Settings button in the Enable and Failback section.

From the "Startup and Fault Recovery" window that opens, clear the "Automatic Restart" item in the "System Failure" column, and click "OK" to complete the setting.

If the problem of automatic system restart cannot be solved after the above settings, then we need to make the following settings: use "win+r" to open the "run" window, enter "msconfig" and press enter to enter the main interface of the system configuration utility.

In the "System Settings" interface, switch to the "General" tab, check the "Diagnostic Startup" item, and click the "OK" button to restart the computer.

When the system reboot is completed, enter the "System Configuration" interface again, switch to the "Services" tab, check the "Hide Windows Services" item, and check the item you want to start automatically with the system, and click "OK" to complete.

The computer general Qing Jane is self-imposed to restart the Yuzhi pants What's going on.

The causes of blue screen tend to focus on incompatible hardware and drivers, problematic software, viruses, etc. Workaround:

1. Causes of the virus. Use anti-virus software to detect and kill viruses.

2. Reasons for memory. Use an eraser to wipe the gold finger of the memory module and wipe off the oxide layer to ensure that the memory module is installed and running normally.

3. The chassis is not clean. The CPU fan has too much dust to run normally, causing the CPU temperature to be too high, so use a brush or hair dryer to clean up the dust on the inner wall of the case, the CPU fan, the graphics card fan, and the motherboard.

Fourth, you can fix the blue screen through PC Manager.

1. Click to open the computer manager computer clinic.

Win10 computer automatically boots up after shutdown solution:

1. Check whether the maintenance settings of the system are turned on.

Go to "Control Panel Systems & Security Security & Maintenance Automatic Maintenance". If it shows that this computer does not have automatic maintenance turned on, then it is not caused by this reason.

2. Open the Event Viewer.

Right-click on the desktop to find this computer (this computer), select "Manage" in the pop-up menu to open computer management, select "Event Viewer" in the left function box, and then locate to Windows Logs - System under Event Viewer.

The analysis here results in a task scheduled by "nttask Microsoft Windows UpdateOrchestrator Reboot", which requests to wake up the computer.

3. Select "Task Scheduler" in the left function box of Computer Management.

Then navigate to the Task Scheduling Library-microsoft-windows-updateorchestrator directory under Task Scheduler;

Find the "reboot" item on the right and double-click to open it; Select the fourth menu "condition" in the open dialog box, cancel the check box in front of waking up the computer to run this task, and then click OK, you can solve the problem of automatic boot after win10 sleep.

You try it, first turn off win10 automatic update:

Press the Windows logo key + R key to open the Run Window command, and enter " in the window command

After opening Group Policyr, we first click on the Computer Configuration - Management Templates - Windows Components menu option.

In the Windows Component menu window, click to select the "Windows Update" submenu item, and then find "Configure Automatic Update" in the configuration options on the right.

If we want to turn off the automatic update function, we should select "Disabled" in the left option, and then click the OK button, so that we can smoothly turn off the automatic update function of the windows 10 system.

Then replace the graphics driver with the driver of win7. Note: Do not use the latest. Just use your previous graphics card driver (preferably before April 2015).

If it no longer restarts automatically, it means that the graphics card driver that win10 updated for you is not compatible.

If it's a problem with the graphics card, you can disable the automatic update of the graphics card driver by using the following methods:

win+r runs the local policy grouper.

Computer Configuration - Management Templates - System - Device Installation - Device Installation Restrictions.

Disables the installation of devices that are not described by other policy groups ——— enabled. (Windows won't be able to install drivers; Note: To install drivers, turn off the policy).

After setting up the WinUpdate Driver will show that the installation failed. You can leave it alone. In the future, you will need to install the hardware driver. Then set it to "Not Configured".

After setting the device not to install the hardware driver automatically, you can turn on automatic updates as before.

Click the "Windows" button in the lower left corner of the desktop of the official version of win10, and click the "File Explorer" item from the extended panel that opens.

2After entering the "File Explorer" interface, find the "This PC" icon from the right side, right-click and select "Properties" from the pop-up right-click menu.

Once the System Properties window opens, switch to the Advanced tab and click the Settings button in the Enable and Failback section.

From the "Startup and Fault Recovery" window that opens, clear the "Automatic Restart" item in the "System Failure" column, and click "OK" to complete the setting.

If the problem of automatic system restart cannot be solved after the above settings, we need to make the following settings: right-click the "Windows" button and select the "Run" item from its right-click menu.

From the "Run" window that opens, enter "msconfig" and press enter to enter the main interface of the system configuration utility.

In the "System Settings" interface, switch to the "General" tab, check the "Diagnostic Startup" item, and click the "OK" button to restart the computer.

When the system reboot is completed, enter the "System Configuration" interface again, switch to the "Services" tab, check the "Hide Windows Services" item, and check the item you want to start automatically with the system, and click "OK" to complete.

If the above methods still do not solve the problem of automatic restart of the computer, make the following settings:

Enter the "Control Panel" - "Power Options" interface in turn, and click the "Select the function of the power button" button on the left side.

Finally, in the "System Settings" interface, clear the "Enable Fast Startup" item from the "Shutdown Settings" column, and click the "Save Modifications" button. At this point, the problem of automatic computer restart has been solved.