How to make up the computer records of students in the school computer room??? I heard that there is

As long as there is a LAN in the school computer room, there is no need to install them one by one.

You can first make a master machine, get the software and settings you need to install, and then enter the interface of the system network engraving. In it you can send your parent system's system down (there is a selective send, you can only send the system disk, or you can send the entire hard disk together, this should be seen clearly when sending).In this way, all the machines in the entire computer room are the same, and after this step is completed, you can assign the IP address again, and that's it.

There is no need to operate one by one.

As you said from the landlord, this situation mainly depends on whether the machine in your school computer room has a network engraving function. Like Lenovo,Tongfang these brand machines are available,If your school's machine is a machine without a network engraving function,Then you can install the teaching software first (this should be there),And then send the software down,This can be installed。 But it still has to be installed one by one. Otherwise, you will have to install the screen engraving function software, which may be a little troublesome, but after installing it, it will be beneficial for you to manage and change the system in the future.

If your school's machine is Lenovo or Tongfang, you can press and hold the shortcut key when you turn on the computer to enter the network engraving interface.

The association is. f4 is the same side.

ctrl+h

The landlord thinks that the hair system is too slow, then I can only say that your machine is too bad.

Even if Lenovo's machine sends the whole disk, it will only take about ten minutes, and if you install the software, it will only send the system disk for a few minutes.

I used to help the school maintain the computer room and network, and there was never any software that could not be used.

If the landlord's machine is really slow, I still recommend that you install them one by one. Otherwise, even if you find a feasible way to install software together, it may cause the entire computer room to be paralyzed because your machine is not working.

The other party shares a folder or hard drive. Right-click attribute of the online neighbor Right-click local connection Status Support to look at your IP and also look at the IP and DNS of the other computer After knowing the other party's IP, such as just look for it on your computer and start running, and then OK, you can see his shared hard disk, you can put it in by yourself, and it's OK.

Set a folder on the machine you want to force the file to be shared, then set the user permission to allow reading and writing, and then you enter his IP address in the browser and click on that folder and just do it.

You can only use hacking software.

If there is a vulnerability, it is easy to deal with it, and it is recommended to go to the hacker forum to check for similar small vulnerabilities.

Give students an ordinary account and don't give it to the system administrator Upstairs said to use a restore card The online is slow Students can use the optical drive to install it It's also very fast, but if you don't give the system administrator, students can't install any software It's also a problem.

It was up to us how the school needed to manage. It's a good idea to set up a guest account for them to use. Permissions for guest accounts can be set in Group Policy.

Take a stick and write on the classroom door: "Players who play the game, don't be responsible for killing them."

Otherwise, I can't figure out how I can't play the game with a computer.

Close the hypervisor and press shift to restart or log out.

It can be in the Task Manager.

It's useless, only to break the code of Vientiane! If it were so easy, everyone would be able to surf the Internet for free at an Internet café!

Hehe, are you the network administrator of the school computer room?

In fact, the principle of this problem is relatively simple, but it is a bit complicated to implement.

To achieve this, first of all, the network cable of the student dormitory is split from the terminal of the school, so that a computer can be selected as the network server, which can control two aspects: one is that the network speed can be controlled, such as broadband traffic, timing network switching, etc.

It's super simple, the student computer side of the school computer room installs a software, what student client and the like, and the end of the process in the task management is not controlled by the teacher's machine!

You can install the domain shield client on the computer in the computer room, and then you can view the real-time desktop of each client on the management side, remote operation, remote viewing, the client does not know what you are looking at when viewing, and you can also audit all the Internet behavior of the client, web browsing search, etc.

Haha you know what

The school's teaching system mostly uses frequency division teaching.

In other words, there are several frequency bands, and the teacher's machine only controls one frequency band.

You can avoid this band and get out of control.

I used to use Founder, multi** electronic classroom, use it, OK, you can try.

Network management software, generally there is a teacher version and a student version, you only need to exit your machine to avoid being controlled by the teacher!

You can disconnect the LAN!! You're a teacher who installed network management software! You must have an installer to uninstall. So you're OK as soon as you show the network cable! ~~