What to do if the camera is burned off and the Canon digital camera is burned?

The battery won't blow out, I'm sure. I'm afraid that the positive and negative poles of the charger and the positive and negative poles of the camera will be wrong and burn the version of the camera, which will be troublesome. But a better camera should have a protection circuit.

You try it like this: see if the battery is not, if it is, make a universal charge and there should be an indication on it. See if it's normal.

Also, if you look at it, you can find a place on the camera where you can put a small battery (that is, the button cell battery on our usual electronic watches), remove it and put it back on after a few minutes. Then you can remove the battery and turn it on with the camera's charger. If it still doesn't work, you can only repair or pay for it.

Good luck!

The output voltage or current is wrong.

The voltage or current is low and may not be bad yet, try charging it with a good charger.

If it is too large, the battery may be burned.

Use a multimeter to test the battery if it burns.

Changing the battery should be fine.

If there is no cosmetic damage, it can be warranted free of charge.

Speed and friends admit mistakes.

Ask a friend to take the warranty.

If you incur a fee, you can pay for it.

It is recommended to go to the camera's customer service to ask, usually the battery is charged, or the motherboard is burned out. If the former, it's OK to change a battery. The latter is more troublesome!

It's best if you buy one and it doesn't broke!

The meaning of repair depends on how much it costs.

Basically, there is no value of maintenance, because it is artificial, not within the scope of the warranty, 1, the maintenance cost will be very high, and, 2, after the repair, the imaging quality is likely not to reach the original level, 3, the general battery of the digital machine is a low-end machine, will not be too expensive, the quality of the accessories will not be too good, but the maintenance and warranty will shrink, and the accessories will be relatively high 4, after the repair of the warranty will automatically expire, if you can't use it after two days and then break or need to pay for it again you need to pay for it again.

Lithium battery single, full, two should be used in parallel, or one by one, I don't know if there is a fuse.

Let's see.

Don't get your hopes up.

It's strange that two lithium batteries don't burn.

No need to fix it, buy a new one.

I really don't need to repair it, and the ** repaired must be expensive, but I don't know if it can be repaired. Let's take a look

The fake battery can't be used, it will lose a lot, ok! All I know is that the assembled battery burned out the laptop.

If you don't get it right, it will hurt the camera

No need to fake the building

The landlord can consider replacing it with another brand of battery, not necessarily the original brand

The voltage of the fake battery is unstable, it is easy to burn the camera, and the fake battery is easy to occur**, which is very harmful.

It seems that it can only be a transformer problem, it seems that you don't understand the circuit, the solution is to find a master to repair, the second is to use the transformer, to buy a charging set with battery power is absolutely safe. And you didn't say that those 3 were burned**? Power circuits?

Or a data interface circuit? I can't tell.

In this case, you can directly ask the person who repaired the camera what the reason should be, and directly ask them what the master should do. In addition, this kind of fault is relatively easy to find and deal with, and it can be dealt with by those who repair the computer, and you can find it locally.

To be more detailed, it should be a problem with the power supply (high voltage or current), or it has been turned on for too long.

It is estimated that there is a problem with the power supply of your computer, so look for an ammeter.

It could be that you have a problem with the data cable.

Mine is a Nikon D100 and now I'm using a Motorola V3 cable. Hehe.

It's okay. If the lz is burned, sympathize.

1.How deep do you fall into the water? When is it time to enter the water for salvage?

2.Did you take out the battery board? And cards.

3.How do you get cold?

Now you really don't want to turn on the machine easily, there is no need to take this risk, just to verify whether the machine is good.

It is advisable to consult such as customer service (but you can only listen to half of what they say), senior professionals. And now continue to dry.

There are questions in the supplementary communication.

It's not certain that it will be burned, but the probability of burning is higher.

Don't experiment now, try again when you're completely dry.