The hard disk cannot be installed with the system. SSD installation system can t be installed?

In fact, as long as a primary partition is OK,It is recommended to back up the data,C、D two partitions are from the new partition or formatted,It's best to use NTFS format,Only keep a primary partition,In the installation of win7, let yourself format the installed partition。

If it's not good, it's best to try it when you're drunk and change the memory, which is often caused by problems with some of the wafers.

There are also 150G and 500G points, which should be caused by the partitioning software you choose, which does not support large hard disk partitions, which is more common in DM partitions. It is recommended to use other software to re-partition the hard disk, such as you can choose PQ, but we recommend using the built-in partitioning software in the Windows Pure Edition installation, the partitioning software that comes with Windows, the partitioning effect is good, the stability is strong, the running speed is fast, it is not easy to make mistakes and the compatibility is the best. May mine be helpful to you and look forward to your adoption.

Thank you. In addition, there are many products on the group IDC network**, which are cheap and have a good reputation.

Upstairs is the right solution,But I think the second (memory) is more likely,If it's a desktop,It's recommended to wipe the dust of the gold finger of the memory,If there are two memory sticks, then go down first.,Take turns to try.。 Second, the problem with the hard disk is not ruled out. Since you have a USB flash drive PE, then you use the hard disk doctor and other hard disk scanning software inside after entering the PE, or PM scan to see if the hard disk has physical or logical bad sectors, and then do the corresponding processing, I will not be verbose here

One, the hard disk may have bad sectors.

Second, there is a problem with the memory.

Three, there is a problem with the motherboard.

The first two can be checked using the substitution method.

The small pole in the upper left corner flashed and flashed, it is estimated that the MBR file of the hard disk is missing, enter the PE, in the PM partition tool, click on the update MBR in the operation, and there is also in the disk doctor, also in the operation, update MBR. It is recommended that LZ use HDDREG to check whether there are bad sectors in the hard disk.

The SSD can't get into the system after installation, and I ask the master for an answer?

The solution to the problem is as follows: 1. First of all, format the newly bought SSD in the computer system, and the best format is not to use a quick format, but to format it slowly. 2. After formatting, install the system with a one-click restore tool, and if there is no accident in the middle, you can be sure that there is no problem with the system installation.

3. When the installation is completed, when rebooting again, the computer system cannot be booted with the SSD, then you can bury the previous system first, **diskgenius software, activate the SSD system, and test again. In general, it can be started. 4. The reason is that the SSD can be read in the original system, but when it is installed in the system, it is not activated as the main area.

Thus making it unable to read the contents of the system. 5. If the above still doesn't work, then it is possible that the system was not installed when it was installed, so you can use other methods.

1. Enter the BIOS and restore the default settings of the BIOS. Generally, press F9 in the BIOS to restore the default settings. Press F10 to save the exit.

2. Insert the USB flash drive boot disk. Press F12 continuously when booting up, and select the USB flash drive with UEFI on the front to start.

3. Install the system according to the prompts, skip the activation interface, and go directly to the select disk interface.

4. On the Select Disk page, delete all partitions of the SSD. Then create the partition. Install the operating system.

BIOS, to change it, boot below UEFI mode to MBR (Legacy) mode, the old machine is SATA:::AHCI mode changed to IDE is normal.

Have you set up the active partition, set the system disk to the active partition, if this doesn't work, then I estimate that your solid state may have a problem, either incompatible, or fake.

The ghost method of doing the system is outdated.

Now directly use the ISO file such as the ISO file of MSDN to write directly to the USB flash drive, and then the USB flash drive boots the installation system.

In other words, a 32g SSD is too small, and 128 is not big.

Solution: 1. Turn on the computer, press F10 to enter the BOIS page, and you will see the following screen, in this page, change the AHCI mode to IDE mode.

2. Enter the diskgenius software, you will see the following screen, click on the quick partition above.

3. After clicking, you will see the following screen, click to select the hard disk.

4. After clicking, you will see the following screen, click the Start Detection, Try Repair button to repair the hard disk.

5. That's it.