The switch is configured with H3C S3600 for port 28

Updated on technology 2024-02-08
8 answers
  1. Anonymous users2024-02-05

    It's almost on, and it's installed tomorrow.

  2. Anonymous users2024-02-04

    The ports of some routers and switches are photoelectric multiplexing, that is, the combo port, by default, the bend is under the ante, and the electrical port is opened, and we need to turn on the switch of the optical port. inter g 0/0/1combo enable fiber

    The operation of the exchange is simpler, you only need to bury the electrical port with a close, and the corresponding optical port will rise.

    The optical port corresponding to the 22nd port of the inter g 1 0 22shutdown false start is 25, then the optical port 25 can be used at this time.

    Product range. Core Routing Switches.

    H3C S9500E Series Routing Switches.

    H3C S9500 series core routing switches.

    H3C S7600 series carrier-grade high-end routing switches.

    H3C S7500E series high-end multiservice routing switches.

    H3C S7500 Series Ethernet Switches.

  3. Anonymous users2024-02-03

    The access of the external network of switch 1 is through e1 0 50, optical fiber access, switch 1 and switch 2 are connected by e1 0 49, non-optical fiber connection, now switch 3 is connected to the Internet, but due to the long distance, it needs to be connected with optical fiber, optical fiber modules are available, optical fiber has been passed, configure it.

    Some routers and switches have ports that are photomultiplexed, that is, combo ports, by default, the electrical ports are opened, and the switch of the optical port needs to be turned on, and the operation of the exchange is simpler, you only need to turn off the electrical port, then the corresponding optical port will rise, and the corresponding optical port of the first 22 ports is 25, then at this time, the 25th optical port can be used.

    There is a digital indication on the panel of the switch, which cannot be seen with a command, the optical port and the electrical port next to it share the same PHY, the agreement is that the electrical port is enabled, the optical port is closed, and the electrical port needs to be set to "down" in the configuration", and the optical port is set to "up"."The H3C 5000 series only needs to turn the electrical port down, and the optical port will be automatically activated.

    Under normal circumstances, all ports of the switch are Hybird ports, and PVID is not configured with any VLAN, the port isolation function is turned off, and the notebooks on both sides can ping as long as the IP is configured in a network segment.

  4. Anonymous users2024-02-02

    1. The superior equipment is an optical modem.

    with routing function), use a network cable to plug in the network port of the optical modem.

    2. The other end of the network cable is inserted into any interface of the switch.

    3. At this time, you can see the other vacant interfaces of the switch, and use the network cable to insert the vacant interface and connect with the computer to achieve the Internet access of multiple computers.

    4. Connect the LAN port of the router to the computer.

    5. Enter the IP address marked on the back of the computer browser address bar in the address bar.

    Press enter and enter your password to log in.

    6. After logging in to the router background, click Interface Settings. Select the WAN port settings, select the Internet access method as dial-up in the settings interface that appears, enter the Internet access and password, and click Save.

    7. Click LAN settings, select DHCP, check the enable DHCP function and click Save.

    8. Plug the home network cable into the WAN port of the router.

    9. At this time, click on the system status to see that you can access the Internet through the routing settings.

    10. Use a network cable to plug in the LAN port of the router.

    11. The other end of the network cable is inserted into any interface of the switch, and the other interfaces can be connected to the computer.

  5. Anonymous users2024-02-01

    1. Drag four terminal devices and one switch first.

    2. In privileged mode, you can view the default VLAN by using the show ip route command. As shown in the figure, the interfaces shown on the switch are all default VLAN1.

    3. Create vlan2 and vlan3 respectively and name them.

    4. Enter the interface in global mode, and after entering the interface mode, add the interfaces F0 1 and F0 2 of the switch to VLAN2 respectively in the access mode.

    5. Add F0 3 and F0 4 to VLAN3 respectively, and the steps are the same as in the previous step.

    6. Click on the terminal device (computer) and switch to IP mode.

    7. Set the IP of PC0 terminal device to static IP, PC0 and PC1 to the same network segment, and PC3 and PC4IP to one network segment.

    8. After setting the IP of each computer. Open Command on PC0.

    9. In PC0, the IP of PC1 will be ping, but the IP of PC3 will not be ping. That's where VLANs come in.

  6. Anonymous users2024-01-31

    In addition, console is the meaning of the control port, not the network port, this port is used to debug the device through the command line, but this switch is too low-end, so there is no console.

  7. Anonymous users2024-01-30

    It's totally okay, it's a bit of a waste of resources to be honest. You can also sell to companies that use a lot of computers. It's enough to buy your own home router. If you do, then you're in H3C

    Add a router in front of the S1224 switch, and your PC is connected to the switch.

  8. Anonymous users2024-01-29

    Your model does not have network management function and does not support VLAN, what do you want to set?

Related questions
14 answers2024-02-08

Scold. The switch works in much the same way as the wire collector you are talking about. >>>More

46 answers2024-02-08

Domestic industrial switches. **Cheap. If it is used as a commercial switch, it is okay. If you are an industrial switch, you don't dare to compliment.

4 answers2024-02-08

The description is not very clear, but it can probably be checked in two aspects. >>>More

27 answers2024-02-08

Turn off the DHCP in the DLINK router, and then change his IP, don't be the same as the Tengda router, and set up each computer to automatically get the IP!

22 answers2024-02-08

My e-home currently needs to buy a wireless router, and then equip each machine with a wireless network card, so that two can access the Internet at the same time. >>>More