Adobe Audition 3 0 recording distortion, master please enter!

1. Recording distortion: It may be that the input signal of your microphone is too strong, resulting in signal overload.

Solution: Reduce the input volume of the microphone so that the maximum volume of the human voice does not exceed 0db (not red) of the signal monitoring bar.

2. No three-dimensional sense: In fact, it is impossible for any single microphone to record a three-dimensional signal, and the three-dimensional sense you say may refer to the sense of space or the unevenness of each frequency band.

Solution: The sense of space should be added when playing the **mix, depending on the reverberation degree of the accompaniment**, using the reverb (rev) effect in Adobe Audition, note that the reverberation will determine the distance perception of the vocal signal, the more reverberation, the farther the sound appears.

The imbalance of the frequency band is directly related to the quality and performance of the sound card and microphone, so it is recommended to use a high sampling rate and accuracy (48K, 20bit) for recording, and then use audio software for post-adjustment, such as EQ. Note: When using this method, it is important to note that the vocal sample rate and precision need to be converted to the same as that of the companion**.

Suggestion: Since Adobe Audition is very resource-intensive, you can consider using SoundForge for recording a single-track signal, and then bring in Audition for effects processing and mixing.

It should have something to do with the sound card.

The microphone I used to use was the same, and it felt quite three-dimensional when I recorded it.

Later, after changing to a better microphone, the voice was recorded.

It's dry and clear, so it may be that the sound card you changed is better than the previous one.

So it makes the sound more real and clearer.

I recommend you try it with the Mixed King.

Not only the recorded sound quality is good, but you can also perform special effects processing on the recorded sound when recording, and there are many functions such as adjusting the rhythm speed, voice changing processing, file mixing, and fading

Resources.

1.If it is a discrete sound card, please reinstall its (ASIO) driver.

4.If it is a discrete sound card, please select the (ASIO) driver of your discrete sound card from the menu above.

Click this, the key is not this, after selecting the recording, click the option, there is a Windows recording console--- select stereo mixing!!

- Set up the audio device - Interface (because the recording is in the interface) - Audio driver exclusive mode checkbox, then set the input port in the control panel and device port, and apply.

aa Chinese version)

1.When you switch to the Multitrack window, it means that you have created a new multitrack project (a session, which is translated as "session" in the Chinese version - that's weird), and you need to "save it as" a "" *ses" (multitrack project file) and give it a name, e.g. "Song Processing" (save to a specified path).

That's when AA 3 lets you record in a multitrack project.

2.In the menu bar, select "Audio Hardware Settings" in the menu, in the pop-up box, under the [View] tab, in the drop-down menus of "Audio Device" and "View Port" ("Default Input", "Default Output"), select Yours (Onboard or Discrete Sound Card); Take another look at the Audio Devices in the [Multitrack View] and [Surround Encoding] tabs, and select your sound card from their drop-down menus, and tap [OK].

Friendly reminder: onboard sound card, please **install ASIO4ALL driver; For a standalone sound card, please install its ASIO driver (a standalone card usually comes with its own ASIO driver).

The above step is the hardware wide acre stare setup. ）

3.The hardware (sound card) input for each track of the AA (New Project) is defaulted to "None" (which means that the audio track and your sound card are not yet connected, so the [R] button is grayed out and not available...).This is also a very clumsy aspect of AA design).

In the control group of the left sidebar of each track, there are 3 long buttons, the top button (the default display is "none"), on the left of it, there is a right-facing arrow (-- it is the input setting button of (hardware -- sound card), click it, the menu will pop up, in the sub-menu of "stereo", hook your sound card (with model name), at this time, the sound card is connected with the audio track; Again, click "Apply to All Tracks" at the bottom of the submenu in Stereo, so that the [R] button for all tracks will turn sauce red (available), and when you click it, it will appear bright red - prerecorded.

Friendly reminder, if a certain track is recording vocals, please select "Mono". (Don't "Apply to all tracks.") ）

2019-02-10audition audio processing software crack installation tutorial record.

There is a problem with this table. Let's break it down one by one:

192k refers to the audio stream of the final recording file, that is, the audio stream that passes through 192k per second, which is also the factor that determines the file size. The calculation is 192*60 8=, that is, the disk space occupied by one minute of recording is.

The second item is two-channel recording, and the third item is 44100 Hz sampling frequency, and the relationship between sampling and reduction is one-half, that is, the reduction frequency is 22050 Hz, which is slightly higher than the upper limit of audio.

The fourth item is the bit depth during recording, that is, the sampling accuracy is 24 bits, that is, one second is divided into 2 to the 24th power for storage. The worst sound cards also support 16-bit, but not all of them support 24-bit recording.

Fifth, the maximum level value is -10 decibels, which you can understand as the maximum instantaneous volume, which is the peak volume.

These parameters are the parameters of the final output file, the maximum level of recording can not exceed -3 decibels, otherwise it is very easy to be distorted, -3 dB can achieve a better signal-to-noise ratio, and finally through standardization to achieve the parameters you want. Make the final parameter selection when exporting. See**.

The first thing you need to do is decide whether you want to record a single track or a multitrack recording, which is mainly used to sample or record something. Multi-track recordings are mainly used for things like singing or playing with tape accompaniment. Single-track recording is very simple, first you need to select the system recording option, that is, in the volume recording option, choose to record with microphone, line or stereo total sound, open your recording microphone, press the red record key to record.

Multi-track recording is more complicated, you need to drag the accompaniment and the like to one of the tracks, then click the recording selection button on the track you want to record (whichever is fine), and then press the record button. It's annoying to type, it's not too detailed, forgive me! If you are interested, please contact me QQ