The U disk cannot enter the PE as follows: The U disk cannot enter the PE when it is started

PE made with mobile phone memory card can go in, it shouldn't be BIOS settings or hardware problems, try to remake a PE disk in another way.

This thing also has the problem of poor compatibility.

Change to a compatible main controller, such as Huirong's Phison's.

Cause: The PE system of the USB flash drive does not support UEFI startup.

Solution: Remake the PE boot disk of the USB flash drive and select "Support UEFI Boot".

The steps are as follows:

1. Start the USB flash drive PE maker and select the USB flash drive;

2. Check "Support UEFI start" and click "Start Production";

3. Make a boot disk will format the U disk, click "OK";

4. During the production process, wait patiently;

5. After the production is completed, click "Yes" to test the startup of the PE boot disk of the USB flash drive, and restart the computer to enter the PE system after the test is passed.

To make a boot disk, it is recommended to use the "U hero maker" to make a PE boot disk with one click to set up the BIOS of the computer: press the DEL key to enter the BIOS settings and select the boot menu interface to set the U disk to boot, in "HARD

diskdrives" inside the select U disk as the first boot device, hard drive "harddisk".

drives" selection: Select the U disk as the first boot device "1stdrive", and complete the settings to boot from the U disk.

Well, first of all, make sure that your USB flash drive boots well?

Also, the problem you described is too hazy.

Let's be specific.

There is not much doubt about this question.

If it is not good to make.

Just reinstall it.

If it's still not good.

Can't be guided.

Then you can try a different USB flash drive.

Memory cards are also available.

Step 1: Turn on the computer and keep pressing F12 to enter the shortcut startup list. Step 2: Press the arrow keys to select the position of the USB flash drive. Step 3: Press the Enter key to enter the PE system.

You need to set the BIOS to boot on the USB flash drive to enter the USB flash drive PE, which can be operated as follows:

1. Press the power button and wait for the computer screen to appear on the boot screen, then press the F2 button to enter the BIOS setting interface. This is shown in the figure below.

2. In the BIOS setup interface that opens, move the cursor to switch the interface to the "Boot" bar, and then move the cursor through the up and down arrow keys and select "Hard Drive Order" to confirm. This is shown in the figure below.

3. In the pop-up Hard Drive Order window, select the U disk to start as the first startup item by moving the cursor, press the F10 key to save and restart the computer after completing the settings.

If you change a computer and you can use it, it should be a problem with the computer BIOS, generally a setting problem, otherwise it is a BIOS problem.

It is recommended to set the BIOS to default to rule out setup issues.

Experience: Computer Maintenance: [1] BIOS Boot Setup.

It could be that your bois is set up incorrectly, or win

PE system file corruption, take a look at the manual.

Teach you how to make a PE system boot disk, how to use the boot U disk to enter the PE system.

<><3. Click one key to make, and click the dialog box to confirm.

<>4. Wait for the data to be written before it can be made.

5. Take Dell computer as an example. Enter the PE method.

A: Press F12 when the logo appears when the boot appears.

b: Use the arrow keys to select the U disk and press enter after starting.

C: Enter the system disk menu of the USB flash drive.

D: Select 2 to enter the PE system.

6. Select U disk boot or disc boot Not all motherboards can enter the selection by pressing F12, it has a motherboard or brand to decide.

Hello,1、It may be a problem with the version of your USB flash drive PE。

2. If the machine uses the new version of PE, it may not be compatible. This may also happen if you use an old PE for a new machine.

3. In addition, it may be a problem with USB flash drive PE, you can try to start it on other computers.

If you just install the system, now the computer can still be used normally, can enter the system, then you don't need any tools, as long as it's a non-C disk directory, you can install it directly. But if the system can't get in, you can only use a USB flash drive or CD, then you have to use the upstairs statement, write the ISO file to the USB flash drive, and install the system in the DOS interface. I don't feel like it's getting into PE simple.

It's not that the installation process is not simple, it's that you write the ISO file to the U disk is more likely to have problems, and if you don't write it well, you can't get into the U disk at all. I saw your picture.,You can enter the system.,You don't need a USB flash drive at all.,Extract ISO directly to a non-C disk.,Click on the installer directly.,Select the main disk.,Image,That's it.。

If there is a problem with the boot disk, find another computer to remake the boot disk and try again.

Generally, it is more difficult to install the system on the U disk, you can buy the system disk for installation, I installed the system before, and the system disk I bought is very good, and it is more suitable than the kind of phone bill of hundreds of dollars outside, which is sold on the Internet

Press the F8 key after booting up, select the U disk to start, the key is that your U disk is the boot disk.

You can also enter the PE system without using a USB flash drive.

I looked at the picture and felt that you were in the wrong place, here is not the motherboard boot item, you still can't do the system with a USB flash drive, and the system is not plugged in and turned on the USB flash drive.