How to access the Internet on the two machines and how to set it up

In fact, the easiest way is to add a small switch, eight ports are very cheap, so you use one of the machines to install dual network cards is much simpler, no need to modify any settings on the machine.

Depending on your requirements, the specific settings can be made like this:

Which machine to use to connect to the dual network card, their configuration and system are satisfied, you can choose any one.

Setup of the dual NIC machine.

NIC 1: Access routing port.

Subnet: Gateway:

dns: header

At the same time, you want to turn on the Internet sharing service network card 2 of the network card: connect another stand-alone machine.

ip:subnet:

Gateway: Empty.

DNS empty is fine.

IP settings of the other machine.

ip:subnet:

Gateway: DNS: Header

The network cable connector of these two machines is made of 568A at one end, and the other end is 568B with the direct connection of the two machines.

There are also many problems with dual-machine interconnection, it takes you a long time to debug, and if the shared machine is shut down, the other machine cannot access the Internet freely, so I still recommend that you add a switch device to access the network, so it is also convenient for you to increase the number of machines in the future.

It's also easy to set up.

Buy a D-Link four-port router, 100 yuan, set it up according to the manual, so that the two computers do not conflict with each other, one can be on, two can also be on at the same time. If you use a switch, it's inconvenient, one of them has to be set as a **server, only that computer is on, and the other can access the Internet.

Buy a home router, connect 2 computers to it, set up automatic dialing in the router, turn on DHCP, and set 2 computers to automatically get an IP address...

2. Open IE again, enter in the address bar, and then OK;

3. Enter the username and password (usually the same as admin) in the login interface that automatically opens, and then confirm;

4. Then automatically enter the "Setup Wizard" mode in the settings page, and set the three main aspects: "Internet access mode", "account password", "wireless opening and password", and then "restart".

Buy a router, set it up according to the instructions, broadband account number, password. That's it!

After dialing up the Internet with the router, then, plug 2 made network cables into the router, and you're good to go.

A total of three network cables are needed, one is external to connect to the router WAN port, two is connected to the computer, one end is connected to the computer, one end is connected to the router LAN port, after connecting, select one of the two computers to enter in the web address bar or a router setting interface will pop up, the account and password are admin by default, after entering, there is a boot interface, always click Next, and then there is an adsl account password, enter your broadband account password, and keep clicking Next until it is completed. Then log out and set the IP addresses of both computers to be obtained automatically. Then you can go online.

If successful, give points. Thank you!!!

It is most convenient to buy a router and connect it with a network cable.

You can also use a switch, but the dial-up computer cannot be shut down, otherwise the other one can only dial by itself.

First you have to have a router.

After you have it, you connect it in the right way, just enter a computer and set it up according to the manual, there are steps, if you still don't understand it.

Let's ask again.

1. Use a router!

2. Use a laptop to build a small LAN with a shared network!

There are generally two ways to share the Internet:

1. Dial-up and sharing Internet access through the computer, the dial-up computer is the host, the broadband connection needs to be shared, and the default gateway of other computers points to the host;

2. Share the Internet through router dial-up, router dial-up, and set IP address segment and DHCP, the computer does not need to dial-up, automatically obtains IP, and plugs in the network cable to be able to access the Internet;

There are differences between the two ways of hardware connection:

Method 1: You only need to add a switch or hub, and a router can also be used, but if it is a router, all ports must be plugged into the LAN port, and the WAN port cannot be plugged in.

In the second way, the other end of the ADSL network cable is plugged into the WAN port of the router, and all computer network cables are plugged into the LAN, and you also need to set the broadband account and password according to the wizard.