Prepare for replacing a disk array with a new disk array and replacing the disk array card

What is the RAID card for your machine? According to the phenomenon you described, it means that this disk is not automatically loaded into the original damaged RAID group by the RAID card, but is treated as a new hard disk, so you will see a format prompt in the system.

Generally, RAID cards can enter the RAID card management interface in two ways, one is the management software installed on Windows, log in to the management software, ** to set up, look at the ID number of the newly added hard disk, and configure it in the management software.

Or the machine needs to turn off and reboot in the BIOS self-test stage, enter the RAID card BIOS (there will be a prompt, usually CTRL+a certain key), and enter the management software in the BIOS to set up.

If the RAID 5 of your system 4 disks is composed of 3 RAID 5 and 1 hot spare, the setup is very simple, and the replacement of the new disk can be set to hotspare. If there is no hotpare set in the RAID of the 4 disks, you need to find the repair place in the management interface to set it, and find someone who understands the settings to operate, the RAID setting information is wrong, and it will be troublesome to reply.

It prompts you to initialize the new hard drive.

Dear, good afternoon, I'm honored to answer for you: The preparations before replacing the disk array card are as follows:1

Back up data: When you replace a disk array card, you need to back up all data bridges to another storage device to prevent data loss. Data can be backed up using backup software to ensure the integrity and security of the data.

2.Know the type of adapter card: Before replacing a disk adapter card, you need to know the model and specifications of the original adapter card so that you can purchase a new adapter of the same type.

At the same time, you need to understand the characteristics and compatibility of the new adapter card to ensure that the new adapter can meet the actual needs. 3.Check the power supply:

The power supply needs to be turned off when replacing the disk array card, so you need to check the status and operation of the power supply first. Make sure that the power supply is stable and can be supplied normally. 4.

Prepare tools: Replacing a disk array card requires the use of tools such as screwdrivers, cables, and so on. These tools need to be prepared before replacement to facilitate operation during the replacement process.

5.Plan for replacement: Replacing a disk array card requires shutting down the system and can affect the overall system operation.

Therefore, a detailed replacement plan needs to be developed to ensure that the replacement process does not affect the normal operation of the system. 6.Backup Drivers and Configuration Files:

Replacing the RAID card may result in the loss of drivers and configuration files, so you need to back up these files in advance. Nian Que can be backed up with Backup Software Sensitive High Localizer to ensure that these files can be recovered in time. It is important to note that replacing a disk array card is a complex operation that requires careful preparation and professional operation to ensure a safe and smooth replacement process.

Hope mine can help you

Pro, replacing a RAID card requires some preparation to ensure the integrity of the data and the stability of the system. Here's what you need to do before replacing your RAID card:1

Back up your data: Make sure to back up all your important data before replacing your RAID card. During the replacement of a RAID card, data loss or data corruption may occur.

Therefore, it is recommended that you back up all your important data to an external storage device or cloud storage service. 2.Prepare a replacement card:

Make sure you have obtained a new RAID card that is the same or compatible with your existing RAID card. Before replacing the card, you also need to have the necessary tools ready, such as a screwdriver and a tool to remove the RAID card. 3.

Understand RAID card configuration: Before replacing a card, you need to know the configuration information of the existing RAID card, such as the RAID level, the size and number of disk arrays, and the location of hot spare disks. 4.

Shut down the system: Before replacing the RAID card, you need to turn off the system and unplug all power supplies. This prevents short circuits or electrical shocks in the circuit when replacing the card.

5.Label and record RAID cards: Before replacing a card, you need to mark and record the location and configuration information of your existing RAID card.

This ensures that the new RAID card can be properly equipped after the card is replaced. 6.Test Backup:

After the card is replaced, the backup needs to be tested to ensure the integrity and availability of the data. The above are some preparations before replacing a RAID card that can help you better protect your data and system. It is recommended to understand and master the process and precautions of replacing the RAID card before replacing it.

Now the hard disk should be SATA, a disk is connected to the motherboard SATA1, B disk is connected to SATA2, you can press the "del" key when you boot up to select SATA1 or SAT2 as the boot disk, enter the system, both disks can be displayed, such as A disk is divided into 3 areas, B disk is divided into 4 areas, you enter "My Computer" to see C, D, E, F, G, H, I These 7 areas, you use cutting, copying and moving.

However, the general power supply only has 1 SATA power connector, and it is estimated that you will have to buy an IDE to transfer the SATA cable.

2. You have a system on the old disk, use the old disk as the main disk, use the old disk system to enter Windows, after entering, if your new hard disk is not partitioned, you can right-click "My Computer" and "Manage" to partition the new disk, after partitioning, you can put the old disk into the new disk.

3. Now the new hard disk is a SATA excuse, and the optical drive is an IDE excuse and cannot be connected to the hard disk.

4,BIOS settings,One or two sentences can't be explained,You connect the old disk to sate1,The new disk is connected to sata2,If you can't get in,That's the new disk as a guide disk,The new disk has no system,It's not right。 You just turn it the other way around, connect the old disk to sata2, and connect the new disk to sata1. However, in general, if the first disk does not have a system, it will automatically default to the system of the second hard disk.

5. Enter Windows, after that, you see a lot of partitions, C, D, E, F, G, H, I, you can copy or cut them to move.