How to solve this problem 10, how to solve this problem

It depends on your bottom line, and if you feel you can afford to hit someone and you're willing to do it, go for it. But I don't think anything that can be solved with his fists is not a problem, he may think that he is joking with you, you just need to make his attitude clear to him, if he still insults you like that, you ignore him, the purpose of his insulting you is to make you angry, unhappy, you just ignore him, in two days he will not be doing it, because it is meaningless. Hope my advice helps.

1 If the first person doesn't listen, you should educate him, because you are his friend, so it doesn't hurt him 2 Everything has to grow, and fighting must also come over Hurt? Are you a woman? Still afraid of getting hurt?

3 The second person lacks life experience, and he is very submissive, and you have to let him have his own opinions, and you have to find an opportunity to let the first person be a human being, otherwise it will become more and more serious.

It depends on what kind of problem you have, but don't worry, it's best to dare to face it and find a way to solve it.

Be tough when it's time to be tough, and blindly backing down won't make everyone like you.

First of all, give a serious verbal warning, and don't do it.

I don't understand anything else.

After unlocking, keep pressing and holding the home screen, swipe left and right to find this page to delete, or cancel the theme settings like negative screen, function page, window plug-in.

From the figure, I don't see the FTP configuration interface, I can only see the FTP of the login ruler, and the above part is the FTP command.

The following is in the command line of ftp, the two commands entered have problems, and the following also prompts invalid commands and English prompts that the command Lingpi failed to execute. Please refer to the FTP command for yourself.

00007b**, which means caused by hardware problems.

1. You can shut down, open the case, wipe and clean the memory, graphics card slot.

2. Reinstall it afterwards.

3. Press del or f2 to enter CMOS at boot, optimize (F9, F10 save and exit) 4. After restarting, see if you can enter the system, or try F8 to enter safe mode.

5. If you can't enter, it's best to reinstall the system. Reference.

Was it normal before? Or is it a system that you just bought or just installed? Please add.

1) If it is a problem with the broadband itself, first directly connect the broadband network cable to test, if it is a broadband problem, contact the broadband customer service to solve it.

2) If it's a problem with the router, such as teasing the fruit that can be used originally, it can't be used for the time being, my own practice is to disconnect the power of the router and plug it in, and I'll take a look. In there is a factory reset settings, from the new strict according to the manual settings can be used, I don't understand, it is not recommended to set up at will (this is under the premise of the correct physical connection, sometimes the router is slow or failed to find the IP address, not that the router is broken).

If it can't be solved all the time, it is recommended to call the customer service of the router, they have **** guidance, I encounter a problem that I can't solve by myself, it is very useful to consult the advice they gave, and they will give the correct advice for your settings or operations.

3) If you turn off the wireless switch, turn it on, if the mountain Luzi is connected to the wireless with software, it is normal for the software to be difficult to use and often have problems, there is no better way, use a router. In addition, it is caused by the network card driver is not or is not suitable, and whether there is a problem with the network cable interface or network cable.

4) If it is caused by a system problem, it is recommended to restore the system or reinstall it.

If you are getting corrupted in the bottom right corner of the file prompt you use CHKDSK tool, if yes, please see the method below.

This is an illegal shutdown or other reason that causes the disk to be damaged, please fix it (fix it for each disk or only fix C).

Built-in disk repair method:

The specific steps are as follows: select the drive letter C in my computer, right-click the mouse to select the properties, select "Tools Start Checking" in the pop-up drive properties window, and select "Automatically repair file system errors" and "Scan and recover bad sectors", and then click Start, the scanning time will vary depending on the disk capacity and scanning options (after doing it according to the above method, a box will pop up, the point is, repair after automatic shutdown, and win78 select the Disk Check button according to the plan).

Bad sectors on the hard drive will lead to corruption or loss of computer system files, computer failure to boot or freeze. Hard disk bad sectors can be repaired using NDD Disk Utility or Scandisk.

If the fault persists, please restore the system or reinstall it (it is still not possible to format the hard disk and repartition and reinstall it, and go to repair it if it does not work).

The computer cannot enter the system after booting up, and the reason is that Windows failed to start, which may be due to a recent hardware or software change. If we encounter the problems described above, we can try to enter the advanced boot options to recover, if we can't recover, we need to make a boot show to repair or reinstall the operating system.

Solution: 1. Enter the advanced boot option for recovery.

1. After booting up, press F8 and other shortcut keys to enter the advanced boot options, and select to enter the "last correct configuration", if the problem is not serious, it will be automatically repaired with the last correct configuration;

2. If it cannot be recovered, select "Safe Mode" in the advanced boot options, then uninstall some recently installed drivers or software, and restart and then enter normal mode;

2. If it still can't be solved or you can't enter the safe mode, use the system CD or make a boot disk to repair the operating system.

Part 3: How to make win7-64bit boot disk.

4. Reinstall or repair the operating system.

1. Insert the boot disk into the computer, boot it and connect it and press the Zhizheng boot button F12 or ESC

2. In the installation interface, repair the operating system in the lower left corner of the repair point to repair. To reinstall the operating system, click Install it now.

boot file missing:

To rebuild the boot file, PE is required, or some other way, such as DOS.

Reinstall,It's easy and fast.,But your C drive data will。。。

The master boot record is missing.

Find a system disk or a U disk with boot, boot up the settings and enter the PE after starting, find the diskgenius software, select the hard disk, right-click, and rebuild the master boot record.