Which waterproof material is best to use for underground waterproofing

First of all, you need to pay attention to the right waterproof material:

Different climates have different requirements and influences on waterproof materials, and materials should be selected according to climatic and regional conditions, such as rainy in the south, waterproof materials should be selected for water-resistant materials, if Erjia waterproof coatings, and cold in the north, especially in multi-choice areas, polymer Guoerjia waterproof materials should be selected that are resistant to low temperature frost heave contraction.

Secondly, the requirements for waterproof materials in different building parts are not the same, and they should also be adapted to local conditions, according to the material construction, in a building, the waterproofing of the roof, wall, underground building and toilet and bathroom is very important.

Because the waterproof layer of the roof is exposed, exposed to the sun and rain, wind and rain, it is necessary to choose waterproof materials with high tensile strength, large elongation and good aging resistance. The leakage of the wall is because the wall is too thin now, mostly made of light blocks, a large number of internal and external joints, and then the combination of doors and windows and the wall, the sealing is not tight, and the rainwater seeps in from the joints. Therefore, the wall waterproofing can not be waterproofed membrane, only elastic waterproof coating, and combined with exterior decoration materials.

The waterproof coating of the toilet and bath is the most suitable, first, because the toilet and bath are not affected by the natural climate and have no temperature changes, so the elongation of the material is not high; Second, because of the small area, many yin and yang angles, and many pipes through the floor, the paint can better meet the needs of the toilet and bathroom; The third is that the wall waterproof layer is pasted with tiles, which has good affinity with the binder, so the coating is the best choice for waterproofing the toilet and bathroom.

The underground waterproof layer is soaked in water or very humid soil for many years, the waterproof material must have good water resistance, and the waterproof layer of the bottom plate should be thick and have a certain ability to resist puncture waterproofing materials. If synthetic polymer coils are used, thermal welded seams are preferred. If the adhesive is used to close the seam, the glue should have excellent water resistance, otherwise the best coil material cannot be selected.

To sum up: in the process of choosing the right waterproof building materials, we should not blindly choose, first of all, we must choose according to the external environment where the building is located and the actual waterproof performance requirements, fully "prescribe the right medicine", Guoerjia waterproof materials, so that you can rest assured, waterproof "medicine" only in this way can you buy excellent waterproof materials suitable for buildings!

Hello, there are many kinds of waterproof materials suitable for underground, such as waterproof membranes, waterproof coatings, etc., depending on your geographical location and climate environment to make a specific choice, Keshun waterproof home materials have quite a variety of kinds, you can take a look.

The basement is characterized by dampness, usually not suitable for living, storage should also pay special attention to moisture-proof and waterproof, coupled with waterproof engineering has always been a big problem in the construction, there are many buildings because of waterproofing is not done, often there will be water seepage, water leakage, etc., which has brought a lot of inconvenience to people. So, what materials are used for basement waterproofing? Next, let's find out together!

1. The waterproof layer of the basement outer wall must be protected by soft, and the brick wall cannot be built for waterproofing, which has been confirmed by countless lessons. However, the project of building walls for protection still exists, and when the backfill is excavated and observed, the waterproof layer will be punctured by the brick wall and water will enter. The materials for basement waterproofing must be rigid-flex, so that they can achieve fully enclosed waterproofing and effectively block the passage of water seepage.

2. After the water emulsion waterproof coating is painted, the water can evaporate to form a film to achieve the purpose of waterproofing. This kind of waterproof coating is effective for waterproofing kitchens, bathrooms, roofs and other parts, but it is not suitable because the underground project is soaked in water for a long time. Because the waterproof membrane will be reduced to paint under long-term immersion in water, it loses its ability to resist leakage.

3. Basement waterproof materials can be made of waterproof coatings, waterproof membranes, this depends on your demand, large area of basement waterproofing can choose waterproof membranes, local waterproof materials can choose waterproof coatings, but now there are many waterproof materials on the market, ** is also uneven, in some brands, such as Oriental Yuhong, Zhuobao, Degao, Keshun, Qinglong, etc., Qinglong's waterproof materials are slightly more favorable.

Conclusion: The above content is about what materials are used for basement waterproofing? I hope it can help you. I believe that after passing the above content, what materials will you use for basement waterproofing? If you have more understanding, if you have any needs in the future, you can also refer to it.

Generally, the walls around the basement are made of outdoor waterproofing, that is, waterproofing outside the building, generally doing membrane waterproofing, membrane is more stable and more durable, and the coating waterproofing is easy to be damaged and leak in the process of earthwork backfilling and sinking. Paint waterproofing is generally used on exterior walls and roofs! The selection of basement waterproof paint must be cautious.

Because the basement is a darker, damp place. Be sure to buy products produced by regular manufacturers with manufacturers, shelf life, and qualifications. Lacquer such as environmental resin can be, and it must be corrosion-resistant, waterproof, non-slip, and wear-resistant.

<> the geographical location of the basement determines that the requirements are more stringent, and the air and moisture are completely different from those on the ground! So it's more troublesome and complicated in workmanship! I think the basement is generally full of clutter, so there's no need to make it too good.

You can buy some online or from places that sell decoration materials. For example, the paint of environmental resin and other kinds can be used, as long as it is waterproof, non-slip and wear-resistant.

A basement is a room in a building that is below the ground level outdoors, and building a basement below the ground floor of the house can improve the efficiency of the building land. The basement is generally composed of a roof, a bottom plate, a side wall, a staircase, a door and a window, a lighting well, etc. Let's take a look at which material is more suitable for decorating the basement wall.

First, establish the nature of the building. If it is built, only a layer of white mulch will do. Secondly, to establish the building environment, such as the tide, use 3 layers of tarpaulin to sandwich asphalt.

I have seen a lot of renovated houses, but for the decoration materials, I don't quite understand, the special feature of the basement is dampness, which brick and that agent are good for dampness? After reading the explanation, the mortar waterproofing agent is better, not only has good adhesion, but also can form a whole with the base surface after application, and has high strength, puncture resistance, simple construction, environmental protection and non-toxic, and can completely resist the wet situation in the basement. It is wishful thinking and naïve to think that a good waterproof adhesive coating alone can solve the waterproof and moisture-proof phenomenon in the basement, and the result is a waste of effort and energy.

The classification of basement waterproofing materials includes polymer waterproof coatings, polymer waterproof coatings, polymer waterproofing membranes, and polymer membranes. The first polymer cement-based waterproof coating with good waterproof effect is recommended.

The classification is actually based on some different decoration materials, for example, this underground waterproof has that kind of professional kind of solid wood, and that kind of professional kind of paint, depending on what kind of paint you choose, because the choice of that kind of paint is easier to use.

Bathroom wash cabinet standard. The size of the sink has some minimum control, the minimum width is 550mm, and the 600mm bathroom has been reduced to about 300mm in order to save space, but even if this is done, the washbasin is not only 300mm wide, and the washbasin must be highlighted, so it is inconvenient to place things. In addition, the key is to leave 550mm from the center of the washbasin to the walls on both sides

1. Cement basement waterproof material is the most common, its application in decoration is relatively early, people are more familiar with it, it is made of sodium silicate and cement mixture, its waterproof effect is very prominent, can avoid external moisture into the basement, can ensure that the basement environment is dry, at the same time it also has corrosion resistance, so the service life will be longer.

2. Polyurethane waterproof coating can also be used in basements, which has strong ductility, so it is convenient for construction and operation, and its strength is extremely high, and it is not easy to break and other problems after long-term use, so it can be used for a long time. It is worth mentioning that there are no joints during the construction of this waterproof coating, so moisture and moisture will not take advantage of the void, so it can ensure that the basement is dry.

3. PCM double-sided self-adhesive waterproof membrane, which is very suitable for basement moisture-proof use, which can completely block the basement moisture into the channel, and its construction is more convenient, generally a few hours can complete the waterproof and moisture-proof construction of the bathroom. And the base of this waterproof material is hard and not easy to be damaged, so the owner can rest assured.

4. Asphalt waterproof coating, cost-effective, can allow owners to buy the best basement waterproof material with a very low **, this product was launched earlier, and has been praised by many users in recent years, for which its quality is very guaranteed.

There are many places where there are basements, but the basement does not see sunlight, so it is necessary to put more effort into waterproofing. When choosing waterproof materials, we must choose good ones and we must guarantee the quality. SoBasement wall waterproofing material which has a good reputationto introduce to you.

1. Reinforced flooring: composite wood flooring, the national standard name of these floors is: laminated wood flooring impregnated with paper. Laminate flooring is often referred to as "gilded sheeting" and the standard name is "laminated wood flooring impregnated with paper".

2. Waterproof coating: refers to the semi-finished product formed by the coating, which will have a certain preventive effect on the problem of water leakage.

3. Asphalt: It is an organic gel material with waterproof and anti-corrosion properties.

1. Diatom mud is a new type of material, which is more in line with it. It has the function of eliminating formaldehyde, purifying indoor air, solving moisture and mold, releasing negative oxygen ions, deodorizing and deodorizing.

2. First make a waterproof layer in the basement, and then according to the specific use, you can make wallpaper, oil Qing Zheng shirt paint and tiles. Or waterproof and make an insulation, the dew is caused by the difference between heat and cold, you can consider using decorative tile veneers that are not too large. In general, it is necessary to pass the mesh fabric from the surface of the original wall, then glue the polystyrene insulating panel, drill the fixed parts, the surface needs to be polished, and then painted.

3. The light in the basement is dark, the air permeability is not good, and it is damp, so it is recommended not to use wallpaper or flooring, you can use paint latex to be waterproof, if you feel that the tiles are cold, you can use tiles that are resistant to wood grain or carpet, etc., so that it is more comfortable and comfortable.

The above is about:Which is the best waterproofing material for the basement wall cluster surfaceand all the knowledge of moisture-proof materials for basement walls. The decoration of the basement should ensure the selection of materials and reasonable implementation, because poor implementation will have an impact on the basement and property.

You can get it for free