Is the tplink wdr7300 router 5G dual band wifi???

TPLink WDR7300 router is a 5G dual-band wireless router, that is, the router uses dual-band technology, which combines the two frequencies with 5GHz into a common SSID channel and uses the same configuration.

The frequency signal transmission rate is 300Mbps, and the transmission rate of the 5GHz frequency signal is 1733Mbps. It can automatically adjust and match a better network signal according to the real-time Internet access rate of the user's terminal.

TPLink WDR7300 is indeed a dual-band wireless router, with two wireless bands and 5G.

The TL-WDR7300 uses multi-frequency integration technology, which combines multiple frequency bands into a single common SSID, using the same configuration. According to the real-time Internet access rate of the terminal, it can automatically adapt to the better signal, and intelligently select the Internet frequency band with higher network speed and less interference for the user. Give full play to the advantages of multiple frequency bands and intelligently optimize the user experience.

Compared with single-band wireless routers, it has a higher wireless transmission rate, stronger anti-interference, stronger wireless signal, higher stability, and is not easy to drop. Dual-band wireless routers have become the mainstream development trend of wireless products.

This is a dual-band wireless router with two wireless bands and 5G.

The router's and 5G refer to the frequency band of the router, and only if the corresponding frequency band is supported can the SSID of the corresponding frequency band be connected.

The differences with 5G are as follows:

It has good penetration, strong anti-attenuation ability and short transmission distance, but because many devices use it, there is a lot of interference and cannot ensure sufficient stability.

5G has poor penetration and long transmission distance.

For the case, it uses 5GHz, which contains the three frequency bands of UNII, and there is coverage from there; The biggest advantage of this frequency band is that there are few applications at present, and many countries need to apply for licenses, so the interference is very small and the quality of transmission can be guaranteed; But the disadvantages are also obvious, the indoor anti-attenuation ability is weak, and the next few walls may stop cooking.

This is a dual-band wireless router with two wireless bands and 5G.

The explanation is as follows:

m refers to the maximum bandwidth supported by the router, and the simple explanation is that the maximum transmission speed of the intranet can be reached This is only theoretical data, and it is easier to understand the bandwidth converted to network speed.

2. AC dual-band refers to the WiFi signal that can transmit and 5G frequency bands. The 5G frequency band has a relatively larger transmission speed, but it is worse than the former to penetrate obstacles, but it solves the problem of interference and congestion of the channel.

3. TP-Link is a router brand, TP is a well-known company specializing in home network equipment.

The TT-Link shrinkage is too serious to be bought. You can take a look at Feixun, Buffalo, Tengda, etc. Dual-band is of little use. At present, there are not many devices that support 5G.

This router is a dual-band (two network frequencies) with 450m coverage, so it is called 900m

It is the bandwidth of the router, which is the connection speed.

The performance of this router is too poor, and those who have used it are scolded, so it is recommended that you go to the router forum to take a look;

The wireless signal performance and quality of a router are not directly related to the number of antennas on the router; The performance and quality of wireless signals are related to the number of amplifier circuits attached to each group of antennas, power amplifier chips, and the power of the antenna itself; Domestic router manufacturers to reduce costs; The main chip used by the router only supports 2 antennas, but the router is equipped with 3 antennas; Reduce or even subtract the amplification circuit and power amplifier chip attached to the antenna, reduce the performance and power of each group of antennas, and increase the number of antennas to cover up; The above is a common practice among domestic router manufacturers; It is recommended to use the mini version of the smart router; Feel free to ask!

The wireless rate can reach up to 300Mbps in the frequency band, and the new generation of 11ac technology is adopted in the 5GHz band, which can improve the frequency modulation efficiency by increasing the bandwidth, and the wireless rate can reach up to 867Mbps

The higher the frequency, the stronger the signal.

Theoretically, 5G signals have a higher frequency than the signal, the wavelength is shorter, and the ability to cross obstacles is worse, but the frequency is generally used at present, and 5G is used less, and there is less chance of interference.

Since the dual-band wireless router has two frequency bands and 5GHz to choose from, as long as you choose the 5GHz frequency band, you can directly avoid this crowded public frequency band, and you can also avoid conflicts with other wireless devices, ensure the stability of the wireless network, prevent the occurrence of disconnection, improve the speed of the wireless network, and the wireless network is unimpeded.

Yes. The TP-WDR5620 is available in two types: normal version and Gigabit version, both of which support wireless transmission at 5GHz frequency.

TP-WDR5620 Gigabit Edition Router.

It should be emphasized that router 5G and mobile phone 5G are not the same concept, and the two should not be confused.

The 5G of the router means that the working frequency of the router is 5GHz, which is 5000MHz.

Currently our router may have two operating frequency bands, both of which are unlicensed spectrum, one is and the other is 5GHz. The high-frequency 5GHz can currently support the protocol, which can be achieved at the ** speed that can be achieved on the usual single-channel WiFi terminal.

The 5G of mobile phones refers to the fifth generation of mobile communication technology, and this G is the abbreviation of the English word "generation".

1. The basic parameters of the TP-Link TL-WDR6300 dual-band router are as follows:

1. Product type: SOHO wireless router.

2. Frequency range: dual frequency (5GHz).

3. Maximum transmission rate: 867Mbps.

4. Network interface: 1 x 10 100Mbps WAN port and 4 x 10 100Mbps LAN port.

5. Number of antennas: 4.

6. WDS function: support WDS wireless bridging.

2. TP-Link 6300 is the original firmware, and the enhanced mode has been used in the signal strength adjustment, as shown in the figure below.

3. Comparison and evaluation of TP-Link WDR6300 and Feixun K2 router.

2. The following data were measured at close range.

3. Feixun K2 connection rate 300M, downlink transmission speed, uplink transmission speed, TPLink 6300 connection rate 300M, downlink, uplink. There is not much difference between the two. For the 300M, both are close to the transfer speed of 20MB s, which is already very good.

However, it also depends on whether the compatibility of the wireless network card is good, and some network cards will be slower even if they are in close proximity, about 14MB.

4. The power adapter of TP-Link 6300 is 9V, with a rated power of less than 8W, while that of Feixun K2 is 12V, with a rated power of 18W. From the actual test, it is concluded that the power consumption of TP6300 is 4W, and Feixun K2 is, so it is very necessary for K2 to be equipped.

Fourth, at different points to test the WiFi signal of TP-Link WDR6300 and Feixun K2 routers.

1. Point A, K2, is significantly stronger than TP6300's WiFi signal, while 5G is basically the same.

2. Point B, Feixun K2's WiFi signal continues to be ahead of TP-Link's 6300, and the 5G WiFi signal of the two is still the same.

3. Point C, point C is far away from the wireless router, about 10 meters away, at this time, 5G begins to have a gap, K2's 5G WiFi signal is stronger than TP-Link6300's 5G.

Summary: Whether from the signal or the actual transmission speed, Feixun K2 is better than TP-Link 6300. If the area is small and used at close range, there is no difference between the two.

If the area is greater than 100 square meters, it is recommended to choose FeixunK2It will be better, after all, the signal is strong and the transmission speed is fast.

Dual-band wireless router, the wireless rate is high, but the wired port rate can't keep up, only 100M, which seriously drags down the wireless speed.

It is recommended to buy one that can pass through the wall.

P router TL-WDR6300 dual-band how to set up wireless bridging method:

Primary Router Settings].

1. Enter the settings interface of the main router, then click [Running Status] in the left option bar, and you can find the DNS server in the WAN port status bar, there are two in total, the primary DNS and the alternative DNS server, record them.

2. Click [Network Parameters] - LAN Port Settings] to set the LAN address of the router to save, at this time, it will be restarted and then return to the settings interface and click [Wireless Settings] - Basic Settings.

3. Set the SSID to TP Link A. Set the wireless channel to: 11. Note: The WDS or Bridge feature must be turned off.

4. Click [Wireless Settings] - Wireless Security Settings, and select WPA-PSK as the encryption method, in this example, 12345678 as an example. Note: WPA WPA2 encryption is more secure and more stable to bridge than the old WE encryption, so WPA WPA2 encryption is recommended.

5. Click [DHCP Server] -- DHC Server Settings] and set [Address Pool Start Address] to; Set the End Address of the Address Pool to Click Save to restart the main router. The main router is set up.

Set up the secondary router].

1. Enter the settings interface of the secondary router.

2. Click [Network Parameters] --LAN Port Settings.

3. Set the LAN address of the secondary router to prevent conflicts with the main router, and it is also convenient to manage the main and secondary routers.

4. Click [Wireless Settings] - Basic Settings.

5. Set the SSID to TP Link-B. Set the wireless channel to: 11.

6. Check [Turn on WDS], click Scan in the pop-up interface, find the SSID of the main router after getting the AP list, that is, TP Link A, click the [Connect] button on the right, select WPA-PSK as the encryption method, fill in the key of the main route: 12345678, (keep it consistent with the main router), and click Save.

7. Because the new WDS function is different from the old bridge and more advanced, you only need to turn on WDS on all secondary routers and fill in the information of the main router, if the main router turns on the WDS or bridge function, please turn it off, otherwise the WDS function cannot be used.

8. Click [Wireless Settings] -- Wireless Security Settings to set the password of the secondary route wireless.

9. Click [DHCP Server] -- DHCP Server Settings], change [Address Pool Start Address] to [Address Pool Start Address] to [Address Pool Start Address]. [Gateway] Fill in the IP address of the main router, that is. The primary and alternate DNS servers fill in the previously recorded addresses to save and reboot the router.

10. The setting is complete and the connection is successful.

Oh, your newly bought router, just make it a level 2 router, the upstairs router is the main router, you first power on your level 2 router and connect 1 wire to the LAN port of the route and the other end is connected to the computer, automatically get the IP, and then enter or acquiesce to the administrator password in the IE address bar of the computer, and set the Internet mode to static route mode after entering, (the condition is that you know the IP address of the main route, such as the IP address subnet mask gateway preferred DNS telecom can also be the same as gateway 1, Save it) and then change the IP address of the LAN port to other segments, not 1 or 0 segments by acquiescence, restart after saving, pull 1 line from the upstairs, connect to your level 2 router (that is, you bought this) to connect to the WAN port, so that you can access the Internet, and what you bought is a level 2 router! View the original post

I think it's good for TP-Link It's generally about straight-line distances, and it's mainly about quality. Someone used it for 3 years, and the power was not cut off and it was not broken.

Configure parameters. Product Type: Wireless Router.

Frequency range: dual frequency (, 5GHz).

Maximum transmission rate: 1750Mbps

Network interface: 3 x 10 100M adaptive LAN ports, support auto mdi mdix

One 10 100m adaptive WAN port, which supports Auto MDI MDIX

Number of antennas: 3, 3 x 5GHz

The steps to set up the TP-Link Router TL-WDR7300 router are as follows:

Line connections. Connect the broadband cable of the front-end Internet access to the WAN port of the router, and connect the Internet computer to any LAN port of 1 3 of the router. Please confirm the line type of home broadband and click the corresponding button**Line connection method:

Note: For details on how to connect the home line, please refer to Router Line Connection Guide.

If you use a wireless terminal such as a laptop or mobile phone to set up your router, connect the signal and follow the next step.

After connecting the line, make sure that the corresponding interface indicator is always on or flashing. After connecting the network cable, the indicator of the corresponding port does not light up?

2. Log in to the management interface.

Open the browser of the computer, clear the address bar and enter the management address of the router or, in the pop-up setting management password interface, set the 6 32-bit management password, click "OK" to log in to the router management interface.

3. Enter the broadband account number and password.

Note: 76% of users are unable to access the Internet due to the wrong broadband account password, please carefully check whether the broadband account password entered is correct, pay attention to distinguish between Chinese and English input, letter uppercase and lowercase, whether the suffix is complete, etc. If you don't know it, check with your broadband operator.

If the Internet access mode is detected as automatically obtaining an IP address or a fixed IP address to access the Internet, follow the wizard prompts and fill in the corresponding parameters.

4. Set the wireless name and password.

Set the wireless name and wireless password corresponding to the 5G wireless network. "Wireless name" is recommended to use a combination of numbers or letters, do not use Chinese, "wireless password" is recommended to set 8 63-bit numbers and letters combination, click "OK". As follows:

Note: If you don't want to set the same wireless password for 5G, you can leave "Same wireless password" unchecked.

5. Create a tp-link ID or complete the setting.

At this point, the router has been set up. After the computer is connected to the router, you can directly open the web page to surf the Internet, and you no longer need to click on the "broadband connection" on the computer to dial up.

If you have other computers that need to access the Internet, use a network cable to connect the computer directly to any free LAN port of the router to access the Internet. If it is a wireless terminal such as a laptop or mobile phone, you can connect to the wireless signal of the router to access the Internet, and you do not need to configure the router.