How to paste wall tiles can be fast and not empty

1. Ceramic tiles must be rejected before use, and those with missing edges, fallen corners, dark wounds and deflection should be removed. 2. Soak the tiles in water until the tiles do not bubble before use, and not less than 2 hours, and the surface can be inlaid only after drying. Tiles with short soaking time will cause early dehydration of the mortar due to fast water absorption, which will affect the adhesive strength of the tile; If the wet tile on the surface is not dried, it is easy to cause floating self-falling, resulting in the hollowing of the tile and falling off.

3. For the base layer with a large flat deviation, it should be leveled with mortar in advance, so that the thickness of the mortar of the inlaid tiles is controlled at 7-10mm, too thick and too thin is not only not conducive to operation, but also affects the quality. 4. Ceramic tile inlay should be corrected with the paste, and it is strictly forbidden to correct the deviation after the inlay mortar collects water. 5. When inlaid tiles, each tile should be accurately estimated when plastering mortar, too much will affect the adjacent tiles, too little is easy to empty, if the tile is on the wall and then fill the ash is also easy to hollow, so it is not allowed to plug the ash at the brick mouth to prevent hollowing.

6. When inlaying tiles, you can press lightly by hand, or tap with a small shovel handle, but it is not advisable to knock more, otherwise it is easy to cause hollowing. 7. The wall should be cleaned in time after the tile is inlaid; The caulking must be dense to prevent leakage.

The tiles should be soaked in water for more than 2 hours before paving, so that the tiles can fully absorb water, and then take out the shade to dry or wipe the clear water; Check whether the plastering of the wall base meets the requirements, and the dirt and dust of the wall base must be removed; When paving, the back of the tile is covered with cement mixed mortar or 108 cement slurry and the wooden handle of a small shovel is tapped on the tile, so that the cement grout is crowded with the back of the tile, and then pressed hard to make the tile firmly combined with the wall base. After the tile is paved and the mortar is solidified, you can use a small hammer to tap the surface of the tile to check whether the tile is hollow.

Construction method: 1. Base surface treatment: remove oil, dust and loose objects on the working surface, clean the tile gaps, and ensure that there is no debris and stagnant water.

2. Stirring: Pour the dry powder into a container containing 27%-29% water in a certain proportion, stir at low speed with an electric mixer, stir while pouring the powder until the thick slurry (like paste) without granulation and precipitation is uniform and free of granulation and precipitation, and then stir for 1-2 minutes before use.

3. Caulking: Use a professional caulking tool to completely press the caulking material into the gap diagonally, and pay attention not to leave it blank. After 10 minutes, wipe off the caulk from the tile surface with a damp sponge or cloth.

4. Cleaning: After the caulking material is dry, use a wrung out wet sponge to clean the surface of the tile. Try to avoid strong direct sunlight within 3 days after construction, and sprinkle water on the construction of the joint filling material every day for a week.

Awesome! It turns out that the wall tiles are pasted quickly and not hollowly, and I learned another trick.

Hollow wall tiles refer to the situation that the wall tiles that have been pasted have gaps or sound hollows. Such situations may lead to loosening and breakage of the brick surface, and at the same time, it is easy to cause the room to be unsightly.

There are many reasons for hollowing out wall tiles, some of which may include:

1.Improper selection of materials: When pasting wall tiles, if the mortar or glue used is not sticky enough or of poor quality, it will be difficult for the bricks to stick to the wall.

2.Improper wall treatment: Improper wall treatment, such as poor quality paint or plaster, can prevent mortar or glue from adhering to the wall.

3.Wall flatness problems: The wall surface has the problem of hanging or uneven, and if it is not properly treated, the pasted bricks will be affected.

4.Improper construction: If the construction personnel are not in place, and there is no correct compaction mortar and bricks in the tiling process, it will cause the mortar to detach from the wall.

5.Moisture problem: When the wall tiles are attached, if there is too much moisture in the mortar, it will affect the hardness and viscosity of the mortar next to the coder, and it is easy to cause the loosening and hollowing of the wall tiles.

6.Defects in the wall tiles themselves: If the purchased bricks themselves are defective, such as hollow or greasy inside, they will also lead to the hollowing of the wall tiles.

Therefore, when pasting wall tiles, we must choose high-quality materials, standardize construction operations, pay special attention to the flatness of the wall, and control factors such as moisture and temperature. If there is still a hollow drum, it should be dealt with in time to repair the wall to ensure that the entire wall is strong and beautiful.

The living room is pasted with wall tiles, a full tile, diamond brick, imitation Dali brick.

First of all: look at the firmness of the wall, such as the wall is soft, the mark is low, and the drum is hollow, which should first strengthen the wall in the tile.

2: The wall is firm, which should be brushed with 901 glue on the wall first to prevent the wall from absorbing water too quickly when tiling, causing the tiles to solidify too quickly and fall off.

Three: on the back of the tile on the brush on the adhesive paste, it will be more firm.

Four: After this treatment, it can be paved with special tile cement and cement and coated behind the tile.

Five: the hollow drum is caused by the cement is not coated when the tiles are pasted, and the coating will not cause the hollow drum of the wall tiles.

The use of polished tiles can avoid falling off, which is conducive to choosing the right decoration style. You can use adhesives, or do a good job of tidying the wall and tiling the tiles, which can ensure the firmness of the tiles.

In fact, the living room wall tiles do not have high requirements for wall tiles, and the requirements for construction techniques are relatively high.

When decorating the house, many people like to put tiles in the living room, which not only makes it convenient to tidy up the environment, but also makes the living room look especially bright, and advances the overall color of the home. However, because the living room wall tile is different from the intimate tile of the cabinet wall, there is often a hollow drum and falling off, many people think that it is a problem with the tile, in fact, the living room sticks to the wall tile falling off and hollowing, this matter is not very related to the tile, the most important thing is the construction technology of the living room against the wall, what kind of tile has what kind of processing technology, this can be maintained not easy to fall off the hollow drum, and the tile can be solid after pasting.

Method: can not be thick paste, engineering construction soft marble slab tile adhesive usually need to choose thin paste method, thin paste method paving layer thickness is only 1-2cm, because the soft marble tile adhesive water retention characteristics are good, the drying rate is relatively slow, so in the case of the adhesive layer is too thick, the expansion and shrinkage rate of the raw material itself is also expanding, which causes the expansion and convergence index between the adhesive layer and the tile and the wall to be not matched, and the compressive strength of the page fusion is reduced.

Do not add concrete to the soft marble slab tile adhesive. Soft marble tile adhesive was originally a product that has been prepared, immediately mixed with water can be applied, if added concrete or other raw materials, it will completely destroy the scientific and reasonable preparation of soft marble tile adhesive itself, and the middle and late stage of tile paving will occur ceramic tile hollowing, falling off and other potential safety hazards.

Can not be used for caulking, soft marble slab tile adhesive and grout are building materials accessories, but the two have a fundamental difference, soft marble slab tile adhesive can only be used to paste tiles and can not be used as a grout agent to apply. If the soft marble slab tile adhesive is used to carry out the caulking, just block the closing joint of the floor tile, if the floor tile is arched up by heat, it will also be easy to produce the hollowing and falling off of the tile.

The total area of tile adhesive can not be scraped at one time, and the total area of soft marble tile adhesive is too large. Soft marble slabs and tile adhesive projects cannot be scraped at one time, and the total area is very large. The surface of acrylic paint is dry and solid, the outdoor is dry, the wind is strong and other irresistible elements.

Because the total area of scraping is too large, the surface will be dry and solid due to the construction of the project, and then the wall tiles will cause risks such as brick dropping.

For the living room wall tiles, it is possible to use some wall tiles with a relatively flat texture and good quality, so that there will be no falling off and hollowing; If you want to paste it more firmly, you should choose the corresponding method, such as wet pasting, or before pasting the wall tiles, you should first carry out the corresponding bubble bricks, and use tile adhesive with strong viscosity.

You can choose strong installation, you can also choose porcelain tiles, and then choose tile adhesive when pasting, and the cement should be evenly coated.

First of all, the wall should be smoothed out and cleaned so that it can be more firmly pasted.