What should I do if the wireless router can t send a signal?

Wireless router can't send signal reason:

Reason 1: Wireless wifi is not turned on.

Turn on the router's wireless function].

1. Enter the router:

Open the browser, enter the general router address in the address bar is this or check the login information on the back of the router) Enter the route - enter the user name, password, (the default is generally admin).

2. Select Wireless Settings --- Basic Settings.

3. Check [Turn on wireless function] and click Save.

Reason 2: The wireless module of the router is damaged, and it is recommended to replace it with a new wireless router.

Is there a reset red dot on the back Press it with a pointed object Turn on the power If there is no wireless send it for repair.

It's not that you can't send a signal, it's definitely your wireless is turned off, or you changed its username, so it can't be transmitted.

Go to the router and see if the wireless feature is enabled. If it is enabled, it cannot be used. That's when the wireless function is broken.

Set up your router again and see how it connects. Enter it in your browser (usually this), and look at the back of the router for your username and password.

1. When the router is powered on, hold the reset hole or button for about 10 seconds, and wait for the indicator lights on the router to turn off and turn on again, and the router will be restored to factory mode successfully.

2. The computer connects the router through the network cable, and uses the default IP address of the router and the default login username and password to log in to enter the router background, and the default IP and user name and password can be queried through the parameter values on the back of the router.

Note: After the router is factory reset, you need to reset the Internet parameters to have a normal Internet experience.

Try it! It is recommended to reset the router and set the dial-up again;

Reset router method;

Method 1: There is a button [RESET] button behind the router, press and hold it for 5 seconds, and then reset it;

Method 2: Go to the router --- System Tools --- reset the router;

Set up router dialing:

Automatic acquisition of computer IP and DNS settings;

1. Enter the router:In the [Setup Wizard], select [PPOE Dialing] (some are ADSL Dialing), enter your Internet username and password as prompted, and save;

2. In [Network Parameters] --WAN Settings], select [Normal Mode], and select [PPOE Dialing] in the three options of [Connection]. The next is to select [Auto Connect], Save, and Exit;

3. If you want to use wireless wifi, your router must have a wireless routing function, in the settings, turn on the wireless routing function, here, the wireless signal signal is changed to one of them. The strongest anti-interference.

You can also set a password for your Wi-Fi connection.

Here's how to fix it:

1. Check the broadband modem, connect the computer to the broadband modem separately, and use the dial-up connection to test whether there is a problem with the broadband itself.

2. Turn off the power of the wireless router and eliminate the problem caused by the overheating of the wireless router.

3. Check whether the network cable connected between the cat and the wireless router is loose, if the branch seepage fruit lamp is not on, you can replace the network cable.

4. The wireless router setting problem may be caused by the wrong broadband and password input.

5. Reset the router to factory settings and reset the wireless router.

1. Is the wireless transmission of the router being turned off by you? Telecom's own cat,Wireless has a button,Press it to turn it on,Press it down and turn it off again。 (It should be wireless that the light is on).

2. Is heat dissipation bad? If it's too hot, it will crash, the program will be wrong, and you need to restart it.

The wifi name of the new route is different from your original one, and the strongest signal in the vicinity is the one you search for.

However, the new route will have to be set again.

The username and password are then routed on the nameplate at the bottom and set by yourself.

If you don't know how to speak, it is recommended to find a professional for help.

Go into the router and see if you set it up correctly, and whether the SSID broadcast is turned on.

You call the computer store to bring a few different brands of routing to your home, try separately, maybe one of them will do.

Let's take a look at the routing settings.

There are 2 ways to do this:

1. Go to the router configuration page, find the system settings, and restart the router.

If these two methods are not good, there are still 2 less common possibilities:

1. Someone else enters the configuration page through the wireless connection, enters the code next to the hood, enters your router page, configures the router, and inadvertently turns off the wireless function (the probability is very small, unless you meet a rookie).

2. The router program is chaotic, you need to return to the factory settings, near the router power supply, there is a reset button, use a toothpick or something, press and hold for 5 seconds, and let go, that is, complete the factory reset, and reconfigure the router Hongfeng.