Water Pipe Cleaning Process How effective is the water pipe cleaning

Cleaning water pipes need to be cleaned by professional people and professional equipment, the process is actually very simple, the whole process takes about an hour, the new water pipe cleaning is currently the best one, after 10 years of precipitation, and constantly open up the market, promote publicity, these two years of water pipe cleaning has gradually been recognized by the public, more and more people have joined our ranks, so that more people can use it, drink healthier water.

The effect of washing out the water pipe of different materials is not the same, the water pipe of each material will produce the phenomenon of fouling, the plastic pipe is easy to accumulate the dirt of bacteria and algae, so it is white turbidity or light green or light yellow when washed, and the iron pipe is easy to rust, so it is brown color; If groundwater is used, whether it is iron or plastic, it can wash out very black and dirty water. Newer buildings will use stainless steel pipes, but over time they will still wash out the white and sticky bacteria and algae.

Joke. No one has really cleaned the water pipes, don't be whimsical, one out is one out, don't go out of your way to clean it at all, the water is flowing.

This is really possible, I use the pipe guard professional tap water cleaning equipment, cleaning a customer is about more than an hour! Half of the hour was chatting with customers, and cleaning was quite easy! They provide information and technical guidance, and the process is not so complicated!

The effect depends on how long the water pipe lasts and how dirty it is! Hope it helps!

1. Why should the tap water pipes be cleaned?

In the newly installed water pipes, some materials are not environmentally friendly, and the peculiar smell of these materials, and even toxic and harmful molecules will enter the water in the pipeline, seriously polluting the water body; In addition, during the installation of pipelines, it is inevitable that there will be other debris such as raw material belt, hemp rope, sealant, etc., which will adhere to the inner wall of the pipeline and pollute the water body.

The water supply pipeline that has been used for a long time, due to the flow of water in the pipe, the oxidation reaction will produce rust, and the sediment that enters the pipe during the installation and repair of the pipeline will be deposited in the pipe, resulting in the inner diameter of the pipe becoming smaller, the water flow is insufficient, the water supply is not smooth, and the pipeline is blocked and the water supply cannot be supplied in serious cases.

In addition, due to the decline in the quality of the water source and the pollution of the secondary water supply, various microorganisms in the water multiply, resulting in the increase of bacteria and viruses in the water, which poses a serious threat to human health. Therefore, cleaning the old water supply pipe network is an effective way to solve the problem of pipeline blockage and poor water supply caused by excessive rust, dirt and sediment, and it is also a necessary measure to purify water quality and ensure the safety of drinking water.

When we buy new clothes, we have to wash them before putting them on, and we have to clean the newly renovated houses before we live in them. People often don't know or forget that the inside of the water pipes also needs to be cleaned; Or, some people will think that you can clean it by yourself by turning on the faucet, but it is actually a misunderstanding, one is that the water pressure is not enough, and the other is that the water pressure alone cannot achieve the ideal cleaning effect, and professional cleaning equipment is needed.

Come and bathe your water pipes!

2. Cleaning method of tap water pipeline.

There are two methods of cleaning tap water pipes: pulse cleaning and chemical reagent dissolution cleaning, and one of them can be cleaned with one of them, or two methods can be combined with cleaning.

Under normal circumstances, pulse cleaning can achieve the cleaning effect, pneumatic pulse cleaning technology, is based on gas and water as the medium, relying on high-speed jet, controllable pulse to form the physical waves, if necessary, add abrasives, simulate the "tornado" impact and vibration of the pipe wall, peel off the rust and deposits layer by layer and quickly remove the pipe, to achieve the purpose of cleaning. It is non-corrosive to the pipeline, pollution-free discharge and can effectively purify the water quality.

However, in some areas, the water hardness is larger, and the content of calcium and magnesium ions is higher, so the water flows in the water pipe for a long time, and there will be more scale attached to the inner wall of the water pipe, and if the scaling time is long, pulse cleaning is not easy to clean off, and the descaler needs to be dissolved and cleaned; Pulse cleaning before and after chemical cleaning is more effective.

Tap water pipe cleaning method steps.

Tool RX-3000 Water Pipe Cleaning Machine.

The first step is to check the pipeline.

Check the position of each outlet of the water pipe, the main valve switch, the position of the washing machine, the position of the toilet, the position and number of water heaters, check the use and quality of the water pipe interface and faucet, etc., and close it.

Step 2: Dissolve citric acid.

Connect the equipment to the water pipe, turn off the household facilities with water inlet function, such as: remove the water heater pipe and connect it with the equipment, pay attention to whether the water heater uses a triangle valve when connecting, if the triangle valve is used, it needs to be removed and directly connected.

The third step is to connect the pipeline for side leakage.

Set the air pressure, turn off all faucets, and use the leak detection function to detect if the water pipes are leaking. Press the leak detection button to fill the pipeline with gas, and after the alarm sounds, keep it for 5 minutes to observe whether the value of the output parameter table continues to decline, if it continues to decline, it means that the water pipe is leaking. After the leak detection is completed, slowly open the faucet at the farthest end of the device to drain the pressure in the pipe.

The fourth step is to soak the liquid.

Turn on the faucet farthest from the device, turn on the faucet, turn on the pumping function, open each faucet in turn to let the lemonade in, and the faucet must be turned off after all the faucets are played. Wait for a while.

Step 5: Pulse cleaning (citric acid cleaning).

Turn on the faucet farthest from the device, turn on the faucet, turn on the pulse function, flush the citric acid and sewage (about one minute), turn on each faucet in turn to let the lemonade be played, and the faucet must be turned off after all the faucets are played.

Step 6: Wash with water.

Allow clean tap water to enter the pipes. Turn on the faucet and start the pulse cleaning function of the device. When the sewage discharged from the faucet becomes clean water, use the pause button to pause the device and turn off the faucet.

Each step should be strictly controlled until the dirt on the inner wall of the water pipe is cleaned. Restore all connections, test all faucets, put away equipment and accessories, and carry out hygienic cleaning.

It is still necessary to clean the tap water pipe, because the water in the pipe stays for a long time all year round, so it is easy to leave toxic substances such as scale, and we can only clean it with professional equipment! This is how the water pipe cleaning industry was born, and the pipe guard cleaning machine is a professional cleaning machine for cleaning water pipes, and the cleaning effect is very good! A treasure is sold, I hope it will help you!

This requires the use of specialized cleaning equipment and specialized technology, using advanced pulse cleaning technology, through the water and gas segmented injection into the pipeline, and emitting different variable frequencies and wavelengths of physical pressure pulses.

Under the action of high-pressure gas, the medium water generates pulsed water waves, which washes the inner wall of the pipeline, so that the rust and bacteria inside the pipeline are separated from the pipe wall, and then discharged into the system through the sewage end. Ensure that all contaminants on the inner wall of the pipeline can be cleaned without any chemicals in the process, which not only prolongs the service life of the pipeline, but also ensures our health and safety issues.

1.Tools & Equipment Used: Water Main Water Pipe Cleaning Machine, Citric Acid, Warm Water (60-80 degrees), Wrench, Pipe, Tee.

2.Water pipe cleaning method:

a.First of all, prepare about three buckets of warm water and dissolve about 1 kilogram of food-grade citric acid in one bucket.

b.Connect the washer and air compressor, close the main water inlet valve at the same time, and drain the remaining water in the pipeline at the same time. Remove the faucet, connect it to our water pipe washer and place the choke tube into the pipe dissolved in citric acid.

c.First of all, the leak detection function is not pure to detect whether the pipeline is tightly connected. After testing that there is no problem with the pipeline, use the liquid injection function to inject the tap water pipeline into the tap water pipe, soak it in the tap water pipe with citric acid solution for about 20 minutes before cleaning.

d.Turn on the faucet and turn on pulse cleaning. Use CACS pulses to remove the dirt and germs on the inner wall of the pipes, and clean the faucets of each water pipe in turn.

e.Finally, use the lead cleaner to check the water pulse until it flows out for cleaning.

f.After cleaning, clean and hygienic and tidy up the equipment.

1. Check whether the equipment is in good condition. Fill the water in a bucket and put a special pipe cleaner in the water. Close the main water valve in your home (usually installed under the kitchen sink) and the water inlet valve of the water heater.

2. Remove the angle valve closest to the main water valve, connect the pulse joint of the cleaning machine, put the suction head of the cleaning equipment into the liquid water, and open the faucet at the end of the home, and the faucet only needs to be turned on a little bit. Turn on the water injection switch, inject the agent into the water pipe, and soak for about half an hour. Both hot and cold water pipes need to be filled with chemical water in batches.

3. After soaking for half an hour, open the main water valve, turn on the air pump and equipment pulse to start scouring the inner wall of the pipeline, and turn on each faucet in turn to clean, and each group will wash for about 15 minutes. Cleaning hot water pipe equipment requires a water inlet, which needs to be connected to tap water or a water pump to pump water to complete the flushing work.

The purpose of cleaning tap water pipes is to remove dirt, bacteria, etc. from the pipes to ensure the cleanliness and safety of tap water.

Here are the steps to clean your water pipes:

1.Confirm the inlet and outlet locations of water mains, close the inlet and outlet valves, and cut off the water source.

2.Open the water pipe drain and remove all stagnant water and debris.

3.Set up protective valves at all exits and openings.

4.Connect the cleaning appliance to the water pipe.

5.Start flushing the water pipes, preferably with a high-pressure flush that pushes the flow backwards through all branches.

6.During the rinsing process, an appropriate amount of cleaning agent, such as bleach, can be added to make the cleaning more thorough.

7.The rinsing time is generally about 30 minutes, and it is recommended to complete it with professional equipment for a longer time.

8.After flushing, remove residual sewage and debris, and flush the water flow in the water pipe.

9.Remove all valves, back-plates, and other appliances.

10.Restore tap water** and test the flow and quality of tap water to ensure a smooth and clean water source.

When cleaning tap water pipes, it must be carried out in strict accordance with the above inspection steps to ensure the cleaning effect and ensure the safety and hygiene of tap water. If you can't do it independently, you can seek a professional water pipe cleaning service provider to operate.

Cleaning of tap water pipes refers to the cleaning, disinfection, descaling and other treatment of tap water pipes to ensure the hygiene, safety and quality of tap water. After long-term use, tap water pipes will accumulate a large amount of dirt, bacteria and microorganisms, which will cause harm to human health if not cleaned in time. Because of this, it is necessary to clean the water pipes regularly.

Cleaning methods include mechanical cleaning, chemical cleaning, high-pressure water cleaning, etc. Cleaning is followed by disinfection to kill bacteria and microorganisms.

<>1. Prepare a pipeline cleaning machine, and wrap the raw meal belt with each joint for later use.

2. Prepare half a basin of water, add half a bottle of citric acid, and another bucket of water for later use.

3. Connect the air pump port, plug in the power supply, inflate the air for standby, and adjust the pressure.

4. Connect the pipette and press the suction port.

5. Connect the output pipe, and the other end is connected to the nearest water pipe.

6. Close the main water inlet valve, turn on the faucet, close the power supply, start by pressing the power supply, and then press chemical cleaning.

7. Turn off the faucet and soak for about 30 minutes after the water is smooth.

8. Put the pipette into the spare bucket and press the physical cleaning to clean Brother Xiaoxiao.

9. Open each faucet in turn to drain the drain.

The following steps can be used to clean water pipes:

1.Prepare the tools.

You need to prepare some tools, such as faucets, water pipe wrenches, disassembly tools, cloth, etc.

2.Turn off water sources.

Before starting cleaning, the main valve of the tap water needs to be closed to avoid wasting the water due to excessive water flow or damaging the water pipes due to excessive water pressure.

3.Disassemble the faucet.

Use a disassembly tool to disassemble the faucet, taking care to protect the surface from scratches or damage.

4.Clean the water pipes.

Use a water hose wrench or other tool to remove the pipe, and then use a cloth or brush to clean the inner wall of the pipe. You can use some special cleaning agents, such as acetic acid, baking soda, etc., add an appropriate amount of water, soak it in a water pipe for a period of time, and then rinse it with water.

5.Flush the water pipes.

After the cleaning is complete, the water hose needs to be rinsed with water to ensure that there is no residue inside.

6.Install water pipes and faucets.

After the cleaning is complete, reinstall the water pipes and faucets, and open the main valve to check for leaks.

It should be noted that water pipe cleaning needs to be done with care to avoid damage to water pipes and faucets. Before cleaning, you should understand the material and service life of the water pipe, so as to avoid orange and damage to the old branches of the water pipe due to improper cleaning. At the same time, we should also pay attention to safe use to avoid potential safety hazards.

Thank you! I will be happy to provide you with a tutorial on cleaning your water pipes. Here's what I've got for you from a first-person perspective:

First of all, I would like to say that I am an amateur who is passionate about home repair and often try various DIY projects, and tap pipe cleaning is one of them. I've gained some experience in this area and I hope it can help you.

Cleaning of water pipes is very important because after long-term use, limescale and dirt may accumulate inside the pipes, resulting in a drop in water quality and unstable water pressure. Here are some of the steps I shared:

1.Prepare tools and materials: You'll need a wrench, a pipe brush, some white vinegar, and hot water.

2.Close the water supply valve: Before starting cleaning, make sure to close the water supply valve to prevent water from flowing.

3.Disassembling the faucet: Use a wrench to remove the faucet and the filter. This ensures a more thorough cleaning process.

4.Wash the faucet: Soak the nozzle and filter in white vinegar, gently scrub with a brush, and rinse off with cavity cleaning water.

5.Clean the pipes: Pour a cup of white vinegar into the faucet interface and let it soak into the pipes. Then wait about fifteen minutes for the white vinegar to descale. Next, rinse the pipes with hot water to wash away the white vinegar and dirt.

6.Install the faucet: Reinstall the cleaned sprinkler head and filter onto the faucet to ensure a secure installation.

7.Open the water supply valve: After completing the above steps, open the water supply valve and let the water flow through the pipe to wash away the remaining white vinegar and impurities. After making sure that there is no water leakage and the water pressure is stable, you can use tap water with confidence.

These are some of my experiences in water pipe cleaning, I hope it will be helpful to you. However, keep in mind that if you have a complex problem or are unsure about the safety of your operation, it is important to consult a professional or relevant authority for help.

Thank you for your question, I hope you find this information helpful!