How to plug in the wRh54G cable of the router

Here's how to set up your router:

1. The broadband bus (the network cable from the cat) connects to the WAN port of the router.

2. Connect one end of the network cable to any LAN port of the router, and connect the other end to the computer, and start the computer and router equipment;

3. After starting the device, open the browser and enter it in the address bar to enter the wireless router settings interface.

4. An account and password to log in to the router appear in the settings interface, enter the default account and password admin

5. According to the setting wizard step by step setting, select the Internet mode, usually ADSL users choose the first PPPoE, if you use other network service providers, select the following two according to the actual situation, if you don't know how to choose, directly select the first item to automatically select, convenient for novice operations, click next after selection;

6. Enter the password applied for from the network service provider, and go directly to the next step after the input is completed;

7. Set the wifi password, try to make the alphanumeric combination more complicated and not easy to be rubbed off the network.

8. After entering correctly, it will prompt whether to restart the router, select Yes to confirm the restart of the router, and you can access the Internet normally after restarting the router.

The steps to set up a wireless network on a Cisco WRH54G router are as follows:

1. First of all, after connecting the wireless router, you need to check whether it is powered on and whether the wireless router is running normally.

2. After checking that it is correct, open the browser and enter: press Enter to enter, at this time a dialog box pops up, you need to enter the account name and password, there will be in the back of the router, in general: account name:

admin password: admin.

3. After entering the password behind the router, you can log in to the settings page of the router.

4. Click on the setup wizard on the page and follow its requirements step by step.

5. Click Next to enter the account password setting, this account password is the account password of the current network network, if you don't know, you can consult the network operator.

6. After setting the account and password for surfing the Internet, the function of wireless Internet access is set, set the wifi name and wifi password, it is recommended that the password is not too simple, it is easy to be cracked, and the encryption method can be recommended by the system.

7. Click Done, restart the router, and the settings have been successful.

Look at the Linksys manual, and configure the IP address of the laptop to be the same network segment as Linksys according to the manual, the first step.

linksys (this is the default, don't change it) notebook IP settings.

Connect the laptop to the LAN port of Linksys (yellow), log in with the web, and set the management address of Linksys, which is recommended to be changed to the same network segment as TP-Link! It can be set to:

Step 2. Restart Linksys, connect to Linksys on the web, set the WAN port dial-up setting (automatic IP), disable DHCP in Linksys, and use DP-Link DHCP to do so.

Turn on wireless, and set the encryption method and SSID name, and the other defaults can be used. Save, restart Linksys, step 3.

Connect the WAN (blue) port of Linksys with the yellow port of TP-Link with a network cable, just like you would on your laptop.

tp-link does not need to be modified.

After debugging, change the default passwords of Linksys and TPLink and record them on the box to prevent others from deleting your settings!

The last address setting is tplink

syslink

Subnet masks are.

Notebooks are automatically assigned for DHCP.

Detailed enough, isn't it? Not detailed enough, there are emoticons in the references!

The wireless router is generally 1 WAN port, 4 LAN ports, insert the line that can access the Internet into the WAN port, and then find a network cable, connect the LAN port of the router to the computer, set the computer IP to Then the web access router, configure the client's account in the router, and connect it automatically. Then turn on the Wi-Fi and set the password. The rest of the computers access the wireless site, configure and route the same network segment, remember that DNS and gateway are both router IP default.

What else do you have to say?

First of all, the DHCP of the router must be easy to use, you try to restore the router, restore the factory settings, don't change other settings, you enter the router at this time, take a look, the wireless settings there, just turn on the wireless network, set the password, nothing else needs to be changed, you test it, whether it is possible. It's best not to set a password before.,See if you can automatically assign an IP.,There's a problem q me.。 515075418

I think the manual should be clearer.

The default username and password of WRH54G are "admin", if you can't log in, consider restoring factory settings, try it. Restore method: Hold down the reset key for 10-15 seconds in the power-on state.

The "Username" field should be blank, do not enter any characters, and the default password is "admin".

I don't know that the security password can't be logged in, it's easy to search for the LAN, the hard thing is the password, there is a kind of wiping device, I bought one. , you can crack passwords, but not all of them. I'm installing a new one now, and I've bought it for nothing.

Poke the reset of this router, revert to the default settings, and then look at the manual settings.

Then you should enter your wireless router on the input **, and then the username, password and verification code will appear in it, you enter them one by one and adjust it. If you have a desktop computer at home and want to use this wireless network, you must also install a wireless receiver on the desktop, and the general computer accessories are sold everywhere and it is not expensive. If you enter it incorrectly, you can only enter the router to change the password and other data if you ask your friend to give him the data he wants to give you.

Good luck!!!

Set up a router to implement the IPTV method of watching telecom wirelessly:

Home Network Environment Cabling]:

1. There is a cat (modem): cat (modem) - router WAN port; The router --- the TV wirelessly.

2. No modem: network cable --- router WAN port; The router --- the TV wirelessly.

Computer enters the router]:

1. The computer IP and DNS settings are automatically obtained.

2. Open the browser, enter the general router address in the address bar is this or check the login information on the back of the router) Enter the route - enter the user name and password, (the default is generally admin).

Set Router Dialing]:

1. In the [Setup Wizard], select [PPPoe Dialing] (some are ADSL Dialing), enter the Internet user name and password according to the prompts, and save.

2. In [Network Parameters] --WAN Settings], select [Normal Mode], and select [PPPoe Dialing] in the three options of [Connection]. The next step is to select [Auto Connect], Save, and Exit.

Turn on the router's wireless function].

1. Select Wireless Settings --- Basic Settings.

2. Check [Turn on wireless function] and click Save.

Set wifi password].

1. Wireless Settings - Wireless Security Settings - Select [WPA-PSK WPA2-PSK].

Authentication Type: Automatic.

Encryption algorithm: AES.

The PSK password is the wireless password. Set the required password.

Hello; Enter in the address bar of the computer or enter the router management background for debugging.

If your current F420 hasn't been cracked, that's how it works:

F420 -- network cable) -- TP - WR845N (set PPPoE on it) -- network cable, wireless) -- connect to the computer.

--Wireless, network cable)--Connect NW330) B700

If the B700 is connected to the wireless network card, and the wireless connection of the F420 is unsuccessful, you can connect the WRH54G wireless:

F420 -- network cable) -- TP - WR845N (set PPPoE on it) -- network cable, wireless) -- connect to the computer.

--Network cable)--LAN port) WRH54G --Network cable, wireless) -- connect B700

Note, do not use the "WAN port of this Cisco router" to connect with the IPTV port of the optical modem, you can use WRH54G as a switch (wireless is also switching), but do not use the WAN port.

This method can be referred to,The linksys model I just installed is:WRH54G wireless router,There may be some places that are different,Some are more set by him,Don't worry about it if you don't have it,Just set it to be able to surf the Internet。

The next Unicom number calculator will do

WAN is set to the PPPoe account password and you can fill in the Unicom to you