How to adjust the TV pan

Push the pot to the south-east, 5 to 7 cm from the surface of the pot, let a person watch the signal quality on the TV, turn the pot left and right, and fix the pot when the quality reaches the highest, and then loosen the support rod up and down, and move the angle of the cauldron up and down, let a person turn on the TV, say stop when the signal is good, tell the person in the adjustment to say don't move, just fix it, and then you can watch it.

Satellite pots. It's a metal parabola.

Responsible for reflecting satellite signals into feeds and high-frequency heads located at the focal point of the satellite antenna. The function of the satellite pot is to collect the weak signals from the satellites and remove the noise as much as possible.

Under normal circumstances, I tried to fix the elevation angle in the place I bought, and then I got it back, and the main thing to come back was to adjust the direction of the satellite, not to adjust the elevation angle, and the satellite position was mostly due south and west. In general, the signal strength is above 60, so you don't need to adjust it very much, and the most important thing is to adjust the signal quality.

Put the small pot on the house, the small pot receiver is moved slowly due south and west, generally it is best to cooperate with 2 people, one on the top to move the small pot, and the other on the bottom to watch the quality of the TV signal. I believe it will be done in a while. Be slow and patient, because the quality of its signal is easy to change with a slight movement, and it is best to adjust the quality to more than 60, so that you can receive about 40 TV stations.

It was done in half an hour and 41 units were received.

First of all, you should place the pot in a place where there are no obstacles that prevent you from receiving the signal.

1. You first slowly turn to the small pot to observe whether it breaks through 0, if it still does not move to 0, then you have to change the following.

2. Adjust the elevation angle to obtain the signal quality, and gently adjust it up and down when the screw behind it is slightly loosened. Be careful, generally do not need to move too much, if the signal quality has not been up, you have to check.

1. Whether the polarization direction of the high-frequency head is correct, and ensure that the 0 scale is directly upward. 、

2. Its elevation angle should be kept at a general angle of 15 degrees behind the vertical deviation.

3. The horizontal direction should be kept at about 43 degrees west-south.

The TV pot is to receive C-band satellite signals, C-band satellite TV local oscillator is 5150, double local oscillator is 5150 and 5750. After installing the antenna and receiver connection, we have used the remote control to enter the settings for program parameter setting

**TV station-integrated channel (CCTV-1) Downlink frequency: 3840 Polarization: horizontal (h) Symbol rate 27500 **V-PID-512 Audio A-PID-650, set it and then click on the information, so that you can see the signal strength and signal quality, the signal strength is generally more than 70%, the signal quality can be received at 30%, and the best two parameters are above 72% and 40%.

The pot noodles are generally about 15 degrees south-west, and the leading angle is about 30 degrees between the pot noodles and the horizontal plane. You can adjust the lead angle and direction of the pot while looking at the signal quality, the signal quality is enough to be above 40, and the signal strength is generally 50% of the high-frequency head of the connection number. Chinese programs generally belong to Zhongxing 6b and Asia 3s

1. Generally, the TV pot has a remote control, and the TV channel can be called up through the remote control. 2. Press the "Menu" button on the remote control, open the TV menu, select "Channel" or "Program Source", and then press the "Confirm Fight" button to enter the program source interface, select the channel of the electric touch Ling TV station with numbers, and press the "OK" button to call up the TV channel. 3. You can also press the "number key" on the remote control to directly enter the channel number of the TV station, and then press the "OK" button to call up the channel of the TV station.

4. If it is a smart TV pot, you can open the main interface of the smart TV pot by pressing the "Home" button on the remote control, and then press the "TV" button to enter the TV channel list, select the TV station with numbers, and press the "OK" button to bring up the TV channel.

1. Adjust the satellite to Zhongxing 6b, and the direction of the pot is southeast! Facing the pan at 4 to 5 o'clock. It also depends on whether the cable from the high-frequency head to the set-top box is plugged in! If the signal strength of Hunan station is adjusted well, it should be fine with other stations.

2. Adjust the azimuth of the antenna to the approximate position, and then slowly rotate the antenna, remember to just let the antenna rotate left and right, so that because the polarization angle and elevation angle of the antenna have been very accurately adjusted, once the azimuth angle of the antenna reaches the target value in the process of rotating left and right, the signal quality will appear, and then after careful adjustment, the signal quality will rise to about 80%, and then it will be aligned with the star, and you can watch the wonderful TV programs transmitted by the satellite normally.

Here's how to adjust the TV pot:

1. There should be no obstacles in the place where the TV pot is placed to prevent blocking the TV receiving signal;

2. Slowly turn the small pot to observe whether it breaks through the 0 scale, and if the 0 scale does not move, it needs to be replaced with 2 scales;

3. To adjust the elevation angle to obtain signal quality, you need to loosen the screws at the back slightly and adjust it up and down gently;

4. Under normal circumstances, there is no need to move a large angle, the signal quality is not good, and it needs to be checked;

5. Check whether the polarization direction of the high-frequency head is correct, and ensure that the 0 scale is directly upward;

6. The elevation angle should be held at a general angle of 15 degrees behind the vertical deviation;

7. In the horizontal direction, keep the beat excited at about 43 degrees due south and west.

Here's how to adjust the TV pot:

1. There should be no obstacles in the place where the TV pot is placed, so as not to block the signal received by the electric blind base;

2. Slowly turn the small pot to observe whether the grinding plum breaks through the 0 scale, and the 0 scale does not move, it needs to be replaced with 2 scale;

3. To adjust the elevation angle to obtain signal quality, you need to loosen the screws at the back slightly and adjust it up and down gently;

4. Under normal circumstances, there is no need to move a large angle, the signal quality is not good, and it needs to be checked;

5. Check whether the polarization direction of the high-frequency head is correct, and ensure that the 0 scale is directly upward;

6. The elevation angle should be kept at a general angle of 15 degrees behind the vertical deviation;

7. The horizontal direction should be kept at about 43 degrees due south and west.