The wireless router is set up incorrectly and needs to be set up again, how to cancel the original s

Press and hold the reset button on the back of the router to factory reset the router and then reinstall the router again.

Preparation: Handle broadband (home network cable), wireless router, an idle network cable, and a computer.

How to set up wifi:

1. The router is plugged in, and the network cable that enters the home is plugged into the WAN port of the router;

2. Connect the computer and the router with another network cable (plug one end into any LAN port of the router, and plug the other end into the computer);

3. After opening the computer browser, enter the IP of the router in the address bar (there is one in the manual, press enter;

4. Enter the username and password of the router, generally the initial username and password are admin (can be found in the manual).

5. Click "Setup Wizard" and click "Next";

6. Select PPPoE (ADSL Virtual Dialing) and click Next.

7. Enter the Internet access and Internet password (that is, the network username and password written in the contract of the network and operator), and click "Next";

8. Select "WPA-PSK WPA2-PSK", enter the password and click "Next" (this password is the WiFi password);

9. After the router is set up, click "Finish".

Then just reply to the exit settings, it's too complicated to say.

If you need to reset the parameters before you can use the router after resetting, the steps to set the road socks are as follows:

1. First of all, the router and the broadband modem.

2. After Zheng Lashu, open the browser and enter the management address and login password of the router.

3. After logging in to the background and shouting defeat, click the setup wizard, and then fill in the corresponding parameters according to the instructions of the wizard.

<>6. After the wireless setting is completed, click Save, and then restart the router to use it normally.

Introduction: A wireless router is a router with wireless coverage function, which is mainly used for users to surf the Internet and wireless coverage. A wireless router can be seen as a device that sends broadband network signals from the wall of your home to nearby wireless network devices (laptops, wifi-enabled mobile phones, etc.) through antennas.

How do I reset a wireless router that has already been set up? I hope it is also the following'The step-by-step tutorial will help you!

There is a reset button on the wireless router, find something and press and hold the reset button, then turn on the power, a few seconds you see all the lights flash (usually like this) on it.

If you use it yourself, you have to go into the router to set it up, generally tp-link is to enter the user and password are admin Other brands are generally , the user and password are admin;

The general manual is written.,Just go in and set up the password.,If it's a bridge with another router.,You have to fill in each other's MAC addresses.。

Reset the router: Find a small hole or button labeled REST (or guest) on the router, poke it with a toothpick for more than 5 seconds, and go back to factory settings.

How to connect and set up the router: Connect the computer to the LAN interface of the router with a network cable, and set the router as follows:

1. Log in to your router (enter or log in in IE, enter the username and password, and the router label is there.) usually admin).

2. Go to the "WAN" setting

A If your broadband requires an account password, set up PPPoE, fill in the account password, select Automatic connection as the connection mode, and confirm that if your operator binds the account to your computer, choose to copy the MAC address of the terminal.

b If you don't need the account password, if you are given a fixed IP, please select a fixed IP address and fill in the correct address of the fixed IP address, mask, gateway, and DNS.

c If you don't need the account password and it is a dynamic IP address, please select a dynamic IP address and fill in the DNS address.

3. Go to the wireless settings, select WEP or WP2-PSK, set the wireless password, and remember this password.

4. Go to the "DHCP" settings and activate the DHCP server.

5. Set "LAN IP" to, remember to use this IP to log in to the router in the future, and save it after setting.

6. Connect the broadband network cable to the "WAN" port of the router, and connect the computer to one of the "LAN" ports of the router.

7. The computer is set to automatically obtain IP address and DNS address.

Computers, mobile phones, and wireless devices should be able to access the Internet.

Advantages of wireless routers:

Intelligent management equipment.

Multi-functional service.

Versatile display tools.

Gain antenna signal.

In wireless networks, the antenna can achieve the purpose of enhancing the wireless signal, which can be understood as an amplifier of the wireless signal. Antennas have different radiation or reception capabilities for different directions in space, and depending on the directionality, there are two types of antennas: omnidirectional and directional.

Omnidirectional antennas: Antennas that radiate and receive in the horizontal plane without a maximum direction are called omnidirectional antennas. Because the omnidirectional antenna is non-directional, it is mostly used in the center station of point-to-multipoint communication. For example, if you want to establish a wireless connection between two adjacent buildings, you can choose this type of antenna.

Directional antennas: Antennas that have one or more directions with maximum radiation-to-reception capability are called directional antennas. The directional antenna has concentrated energy and higher gain than the omnidirectional antenna, which is suitable for long-distance point-to-point communication, and has strong anti-interference ability due to its directionality.

For example, in a residential area, this type of antenna can be selected when it is necessary to establish a wireless connection across several buildings.

Find a small hole or a button on the router, usually marked with the word reset, press and hold the button with a thin needle or hand for a few seconds until the light flashes all the way and the router is factory reset.

Press the reset button on the router for more than 3 seconds, and some can reset to the initial state by pressing it first, then powering on and holding it for more than 3 seconds.

It is recommended to restore the router to factory settings and try it, that is, there is a reset button at the back, press and hold for more than 5 seconds, and all the lights in front can be lit at the same time.

You can press the reset key again with a toothpick, refresh the original settings, and then insert the network cable into any of the 1,2,3,4 ports, in IE is input under normal circumstances, as long as you haven't changed the initial IP address in the settings page before, this is it, once you change it, only you know what IP is entered. At this point, you must be changing your computer's IP address to OK. You should be able to have a login page where you can enter your username:

admin, password: admin. Enter the setting page, the setup wizard will pop up, click Next, if there is no pop-up setup wizard, you can also click the setup wizard directly from the menu item on the left.

After that, plug the other end of the network cable on your modem into the WAN port, and you can automatically dial up the connection.

Because your addresses 1 and 2 are wrong, so the router itself cannot dial up, you have to plug the network cable on the modem into the rest of the ports 1 and 4, using dynamic IP settings, and each computer connected to the network is connected with ADSL username and password respectively.

This method only needs to dial every time, but it does not need to be automatically dialed by the router, if your broadband is time-limited, I recommend you to use this method, no need to connect, both economical and easy to use, I hope you are satisfied.

Then you see if your main line is connected to the WLAN port, if not, press and hold the reset button for 5 seconds, disconnect the power supply, wait a minute, connect the power supply, you are trying!!

Restart it, find out the manual, and set it step by step.