Get in the car and contact to start, what is the order of operation, and the details of step by step

Operation sequence: 1. Step 1: Shake the gear lever to check whether it is in neutral, turn on the ignition switch, start the engine correctly, and observe whether the working instruments are normal.

2. Step 2: Adjust the rearview mirror, and check whether there is any unsafe situation in the back of the car and the surrounding area, and then step on the clutch pedal.

3. Step 3: Hang the gear lever into the starting gear (1st or 2nd gear).

4. Step 4: Honk the horn, turn on the turn signal, and observe the front, left and right sides and rearview mirrors at the same time to see if there is any obstruction to the start, pay special attention to safety.

5. Step 5: Hold the steering wheel steadily, turn on the left turn signal, and release the parking brake lever.

6. Step 6: Release the clutch pedal with the left foot according to the essentials, and at the same time step on the accelerator pedal moderately to make the vehicle start smoothly.

What are the steps to get started with the car, and what are the operation steps.

1. Get in the car and sit down, 3 fasten the seat belt, 4 insert the key, 5 step on the clutch, 6 check whether it is neutral, 7 start, 8 hang a gear, 9 release the handbrake, 10 lightly fuel and slowly release the clutch .........Didi, and left.

A correct start is a good start to driving, and the correct starting sequence of a motor vehicle is as follows:

Manual transmission of cars

1. Start the engine and check whether the working of each instrument is normal.

2. Press the clutch pedal and put the gear lever into low gear.

3. Turn on the left turn signal, honk the horn and observe the front, left and right, above and rearview mirrors of the vehicle at the same time, check whether there is any situation that hinders the car from starting, and be sure to pay attention to safety when starting.

4. Relax the parking brake lever.

5. Hold the steering wheel, relax the clutch foot plate with your left foot according to the essentials, and slowly press the accelerator pedal at the same time to make the car start smoothly.

6. When the car enters the normal driving route after starting, the left turn signal can be turned off.

Automatic transmission cars

1. Press the Jiwei brake pedal, push the gear lever to the D position, and check that the D position indicator light on the dashboard is correct.

2. Turn on the left turn signal, honk the horn, observe the front, left and right, above and rearview mirrors of the vehicle at the same time, and relax the parking brake joystick when there is no obstacle.

3. Lift the brake pedal and press the accelerator pedal slowly and smoothly to make the car start smoothly.

Automatic transmission means that the driver does not need to manually change gears, and the vehicle will automatically choose the appropriate gear for Bo Zhaopei according to the speed and traffic conditions. There are six gears on a general automatic transmission car, from top to bottom: P, R, N, D, S, and L.

Common misconceptions about driving

1. The car starts to warm up for a long time. Preheating the car before starting can make the mechanical parts get better lubrication, reduce friction and prolong the service life. However, the warm-up time should not be too long, so that the lubricating oil can reach the required lubrication parts, too long time, will only cause more fuel consumption and greater engine wear.

2. Play the steering wheel with one hand. When the vehicle is driving fast or encountering an emergency, it needs to control the steering wheel with both hands to save the day, and it is impossible to rely on Guess Wang to do it with one hand. The correct approach is to keep both hands on the steering wheel at all times, and the rider who drives a manual transmission car, once the right hand is shifted, immediately hold the steering wheel back to ensure that the direction of the car is always under the control of his own hands is the safety guarantee.

3. Don't turn on the lights when the visual condition is poor. In order to save the car battery and reduce the wear and tear, many car owners do not like to turn on the lights at dusk or when the weather is dark, which is also a very wrong approach.

Because when the weather or light conditions are poor, it is often difficult for people to quickly detect the whereabouts of vehicles, and lights become the best warning target at this time. To ensure safety, in addition to driving carefully, you must also provide a warning to others, such as horns and lights.

The order of starting is as follows:1. You must go around the front of the car and then enter the car through the front door.

2. Adjust the seat, rearview mirror, and wear a seat belt.

3. First hang neutral, and then turn the key to ignite (you can step on the clutch when ignition).

4. Step on the clutch and hang a gear.

5. From the rearview mirror and whether the reputation or the front of the car ** meets the driving conditions, and then hit the left turn signal.

There are two situations in which the steps to drive are different:

1) The car is parked on flat ground: put the handbrake down, slowly lift the clutch, when you feel the car shake violently, you should hold still, if the car does not respond, then lift a little more, feel the car after moving around, the gas pedal, the car will be started.

2) The car is parked on the slope: step on the clutch and foot brake, put the handbrake down, slowly lift the clutch, when you feel the car shake violently, you should stabilize the clutch and not move, the foot brake quickly let go, if the car does not respond, then lift the clutch a little more, feel the car move around, and then refuel.

Car starting sequence formula.

Formula 1: One step two hang three lights, four look at five press six loose brakes, seven fast and eight slow at the same time, nine lift the clutch and then observe, safe and ten off the light.

Formula 2 Mingwu:

Formula three:

The operation sequence of the manual transmission shouting spring draft vehicle is as follows: 1. Start the engine and check whether the work of each Zheng Xiao's instrument is normal; 2. Press the clutch pedal and put the gear lever into low gear. 3. Turn on the left turn signal, honk the horn and observe the front, left and right, above and rearview mirrors of the vehicle at the same time to check whether there is any situation that hinders the car from starting, and be sure to pay attention to safety when starting; 4. Relax the parking brake lever. 5. Hold the steering wheel, relax the clutch foot plate with the left foot according to the essentials, and slowly press the Gassenzhou speed pedal at the same time to make the car start smoothly; 6. When the car enters the normal driving route after starting, the left turn signal can be turned off. Manual transmission is the use of manual shift mechanical transmission to adjust the speed, that is, to change the gear meshing position in the transmission by hand toggle the gear meshing position, change the transmission ratio, so as to achieve the purpose of shifting, when stepping on the clutch, the gear lever can be moved.

Whether it is a manual transmission or an automatic transmission car, the vehicle must first ignite and start the engine, step on the clutch to hang a gear, hit the left turn signal, release the clutch, step on the accelerator pedal, start smoothly, start back on the normal lane, and hit the turn signal.

The correct starting sequence of the automatic transmission car: 1. Turn the ignition key to the second grid, go to the power gear, and let the car computer system start self-test for at least 6 seconds; 2. Press the foot brake and pull the gear from P gear to N gear; 3. Release the foot brake, turn the ignition key to the ignition gear to start the engine; 4. Step on the foot brake, release the handbrake, and pull the gear from N gear to D gear; 5. Slowly release the foot brake and start. Correct starting sequence for a manual transmission car:

1. Insert the key into the ignition lock, turn on the ignition switch, observe whether the instruments are working normally, and start the engine. If the instrument is not working properly, the engine should be turned off immediately, and the engine can be restarted only after checking and eliminating the fault; 2. Step on the clutch pedal and hang the gear lever into the 1st gear position; 3. Turn on the left turn signal, honk the horn, and observe the front of the vehicle, the left side and the right, the top and the rearview mirror to see if there is any obstacle to the start; 4. Release the handbrake and hold the steering wheel steadily; 5. Lift the clutch lightly, slowly lift the left foot up until the clutch is in a semi-clutch state, according to the different induction points of the clutch, the half-clutch height is different, generally raised between 30-45 degrees, the vehicle begins to vibrate slightly, and the noise at this time means that the vehicle has enough power to start. (Photo by photo:.)

Pacific Automobile Network Lin Hong).