The speed of the Citroen C5 during the run in period share the experience .

It's not to control the speed, it's to control the speed, because Citroen is a high ** motive, so the speed does not exceed 2500 is no problem, the maximum speed is recommended not to exceed 100, and don't pull people!

During the run-in period, try to drive as steadily as possible, and the speed of the vehicle does not exceed 100!

It is best to control the speed at 50 to 80 km/h. After driving for 1500 kilometers, the speed and speed of the vehicle can be gradually increased to the maximum speed allowed by the vehicle, and the accelerator can be pressed hard to ensure that the piston, cylinder and some other important components can increase the load in a relaxed state.

Gear should be changed frequently, do not use a gear for a long time, start with a low gear, gradually change to a high gear, and drive step by step. The phenomenon of low gear and high speed, high gear and low speed must be avoided.

Brake disengagement.

Control engine speed:

The run-in period is not to control the speed of the car, but to control the speed of the engine, the engine speed is controlled between 2000-3000rpm (gasoline engine) The load of the engine is the lightest, due to the poor lubrication during the run-in period, too high speed is easy to strain the components, the speed is too low (the gear is too high), the power of the engine to do work becomes an impact, which will also cause wear, so it is necessary to change gears frequently to control the engine speed. Automatic transmission cars only need to control the engine speed below 3000rpm.

Reduce load: During the run-in period, because the best lubrication state can not be reached, the heavy load will aggravate the wear, so try to reduce the load in the first 500 kilometers, and do not exceed 50% of the maximum load during the 3000 kilometers running-in period, and then gradually increase the load after the running-in period. In addition, the braking system is not fully running-in, the braking effect is not good, and the load also needs to be lightened.

Don't change the oil too soon:

The initial oil of the car is a special lubricating oil during the run-in period, which requires low viscosity, good heat dissipation, superior cleaning and oxidation resistance, and some car factories have also added abrasives that are conducive to the run-in, so the oil should not be replaced too soon during the run-in period. There is no need to worry about excessive abrasive debris as they will remain in the filter and the oil can be changed at the time specified by the manufacturer. It is also important to change the oil for the first time after the break-in period, and it is still necessary to use a lower viscosity oil, such as:

Viscosity of SAE5W30.

Do not use additives:

New car owners cherish their new cars very much, and they are also the most likely to be persuaded to buy some so-called "protective products" at this time. After additives are added to the engine oil during the run-in period, it will seriously affect the run-in effect, prolong the run-in period, and even produce a chemical reaction with the oil additives, forming oil sludge or bubbles, which will reduce the oil pressure, and at the same time make the lubrication worse and accelerate the speed of wear, so do not use any additives during the run-in period.

Warm up before you start:

The new car must be warmed up before starting, the so-called preheating is actually to give the engine a full lubrication time, because the lubricating oil can not reach the friction surface immediately after starting, so it is necessary to wait until the lubricating oil has reached all the parts that need to be lubricated (especially turbocharged models) before starting. The time for adequate lubrication varies depending on the air temperature, oil viscosity, and permeability of the oil filter, so it takes at least one minute to ensure that the lubrication is in place.

What should I pay attention to when running in the new Citroen C5 car? The day before yesterday I mentioned a new car, drove 100km, during the run-in period, some people said that they were waiting for such a sectional grinding, each kilometer drove a few hundred kilometers, the Internet said that as long as it did not exceed 80km, I had not driven a car before, please elaborate, thank you! Another question is, how to increase the speed, but the speed is not too fast?

Netizen Marseille C5 said: Don't worry, novices or safety first. Now the car run-in does not have to be done deliberately, wait until you drive about 3000 kilometers to talk about it Now it is generally not more than 120, C5 is no problem with high speed.

Netizen hbfz660 said: Without the delicate grind you said, my drive back will be more than 100, haha, it's best not to exceed 100

1. Keep the start steady, avoid slamming on the accelerator, and don't make the engine speed too high.

2. Before starting, the water temperature should reach more than 50. Start in low gear, change to high gear after 1 km, and the water temperature should be controlled at 80 -90 in driving.

3. Shift gears in time while traveling, do not use a gear for a long time, and do not use high-speed gear to drive at low speed or use low-speed gear to drive at high speed.

4. Choose a good road surface to avoid excessive vibration, collision or emergency braking. Before braking, the combiner should be disengaged.

5. Choose high-quality fuel and engine oil, and do not use engine wear-resistant additives.

Precautions: Vehicles in the run-in period should be checked frequently at ordinary times to find problems in advance and eliminate it.

1.Engine oil, cooling water, tire gas, etc., must be sufficient, no leakage occurs, and should be replenished in time when a deficit is found.

2.If there is an abnormal sound in each part, it should be repaired in time, and the impact of mechanical failure during the run-in period on the vehicle is often much greater than that of the vehicle that has passed the run-in period.

3.Generally, there are warning lights in the dashboard, and some cars even have computers installed on them. Only by discovering the alarm information in the dashboard and computer in time can we better control the condition of the vehicle.

4.The loading quality of the vehicle in the running-in period must not exceed 70% of the rated load capacity, and the full load and overload will cause great damage to each component of the new car.

Don't accelerate sharply, driving at an average speed is good for the run-in period of the new car, and it saves fuel.

How does a new car run in? Hello, let me ask you this question: 1. The run-in period is generally divided into three stages, the first stage is generally considered to be 0-1000 kilometers, that is, this stage should keep the speed can not be too high, generally not more than 80 yards is appropriate, the speed can be initially run-in in this period, basically 0-4000 rpm should be properly run-in, and the throttle should not be too heavy.

2, the second stage of 1000-3000 kilometers, this period, the speed can still not exceed 80 yards, the speed continues to run-in, the throttle can be appropriately added some kilometers - 5000 kilometers, during this period can be the first insurance, the first insurance after the high-speed, that is, between 80-120 or 130 yards, each speed of the car can be used at a constant speed for more than ten minutes, at this time the throttle can be used as much as possible, there is no clear requirement for the speed, personal recommendations do not exceed 4500 revolutions. 4. The time of the first insurance can be carried out within 5000 kilometers after 3000 kilometers. 5. Pull the high-speed, 1 time 2 times is enough, there is no need to go to Dora, I personally recommend to do the first insurance, and then pull the high-speed, of course, there are also 4S recommendations to pull the high-speed first, and then do the first insurance, in fact, they are all the same.

If my answer is helpful to you, please set it to.

The correct way for Dongfeng Citroen C5 to pull high speed:

1. There is no scientific basis for pulling the high-speed, but the driving feeling of the car that pulls the high-speed is much better than before the pulling;

2. The mileage of the high-speed car should be about 8000km, so as to ensure that the engine, gearbox and other components are fully running-in;

3. The high-speed pull should be carried out 200km after maintenance (oil and filter) to ensure that the vehicle is in an absolutely good state;

4. Safety first when pulling the high-speed, the speed is more than 3500 at the speed of 140 150km h**, and it is best to reach 4000) is enough, there is no need to blindly pursue high speed for a long time;

5. The high-speed should be once every 5000km, which can ensure that the residual fuel of the engine is fully burned and the carbon deposit is reduced;

6. Check the tires for hidden dangers before pulling the high-speed;

7. After pulling the high-speed, you should go to the 4S shop to lift the car to see if there is leakage of engine oil and transmission oil;

km h will have a slight resonance of the whole vehicle, which is a normal phenomenon;

9. When pulling the high speed, you should do more variable speed exercise instead of maintaining a fixed speed for a long time.

Normal driving, 2000 km, 5000 km, 10,000 km 3 points to change the oil on time is OK. If you want to pull the high speed, use the manual mode to force the low gear to make the rev higher, it is recommended to do this after 5,000 kilometers, and open after 10,000 kilometers

The run-in period of new cars is generally 3000-5000 kilometers. New cars in the run-in period need to pay attention to the following aspects:1

The engine speed should not be too high, preferably not more than 3000 rpm, and the speed at 60-90 km/h is ideal. 2.There should be a process of warming up the car during the cold start, and then driving on the road after the water temperature changes, generally about 3-5 minutes.

3.Don't rush to refuel or brake, try to keep driving at a constant speed. The maximum speed of the vehicle within the run-in period should not exceed 100 kilometers per hour, but it is not allowed to drive at low speed for a long time.

4.Do not overload people and goods in the vehicle, and do not exceed 70% of the vehicle's carrying weight. 5.

According to the requirements of the manufacturer or 4S shop, do the first maintenance in time.