Problems with the connection settings of the wireless router???

The setting is too complicated, you can refer to the manual to set up, I only explain here to set the router to a static IP, that is, to give you the IP and then set the connection password of the wireless router, the IP address of the wireless network card on your laptop and the router are set in an IP segment, and finally search for an available wireless network, the name of the router will appear, and you can enter the password after selecting the router to access the Internet. That's probably it, I'll just set it up, and if I put it into words, that's all I can say [s:142].

s:5]

Connect ADSL

The modem is connected to the WAN interface;

The desktop is connected to the LAN port.

Plug in the power supply; Restart your computer.

Router settings.

Turn on IE, enter.

Username: admin; Password: (empty);

Go to the home page and click"tools"to set a new password;

Click "Time Setting" on the left to turn off NTP and set the time manually;

Go back to "Home", enter "WAN", select static IP, enter an IP and subnet mask assigned to you, as well as DNS, click "WiFi" on the left, and modify the SSID name and channel. Security mode: WPA-PSK, encryption mode:

AES and enter a shared password.

Other settings (security) are to turn off DHCP, to set an IP for each computer, e.g., subnet mask, gateway is, DNS address: DNS assigned to you in units! Turn off SSID broadcasting;

Note: Make a note of the IP address of your laptop's wired network card (it should be specified as 3 by default after starting connection sharing, and connect the WAN port of your wireless router to the laptop's wired network card interface with a network cable.

Note: (1) The IP address of the router WAN is to be specified manually. The first 3 digits of the IP address must be the same as the first 3 digits of the IP address of the wired network card, and the 4th digit must not be the same. subnet mask; The address of the gateway and DNS is the IP address of the laptop wired network card (such as the one above).

2) For wireless security issues of wireless routers, decide whether to encrypt the wireless or not.

4. Friends can directly connect to your wireless router to access the Internet.

Access process: Friends - > their own wireless router - > their own wired network card - > Internet connection sharing - > their own wireless network card - > other people's wireless router - > Internet

Check the security level of the wireless router,If the book is older,Don't support WPA2,You can set it to WPA or WEP to see。

It depends on whether your router has a wireless bridging function, and if it does, it does.

1. Connection: **The "LINE" interface of the cat is connected to the "LAN" interface of the cat, the "LAN" interface of the cat is connected to the "WAN" interface of the router with a network cable, and the LAN 1, LAN 2, LAN 3 and LAN 4 interfaces of the router are connected to each host.

2. Set the IP and DNS acquisition method to automatic. Right-click the Local Connection property Network Internet Protocol property, and the upper and lower points will be automatically obtained.

3. Check the IP address at the bottom of the router like ", enter the IP address you see in the browser address bar, log in to the router settings interface, fill in the username and password of the login interface "admin", and then follow the Chinese prompts to enter the account and password.

4.The signal of a wireless network can be affected by a variety of factors, so it is normal for the speed to change

And there won't, e-mail me.

Use the cat to connect the WAN port of your wireless route,Wired Internet computer connection 1-4 port which,Then use the wired computer to log in to the management interface of the route to set up,Enter this is generally the default gateway in the address bar of the IE browser,If it doesn't work, you have to trouble a little bit,Enter cmd in the start - run - ipconfig,Look at the address of gatway (that) The username and password are generally admin,If not, you can read the manualOnce inside, you can set up wireless Internet access.

The cat is connected to the WAN port of the wireless router.

Then enter the route settings and it's OK.。。

Did you just buy a router? The service is missing, the general boss will set it up for you, call ** ask the boss, this is the most practical! Hehe......I am a corporate network engineer in my business.

If you have used a laptop network cable to connect to that network before, then you should directly answer the "wireless router" as a "wireless switch";

The specific method is to plug the network cable (access) directly into the LAN port of the "wireless router", the IP address and gateway of the original ordinary network card are unchanged, (you can still access the Internet with a network cable), and the wireless network card is set to IP+1 with the original network card (such as the original is, then it is, the gateway address and subnet mask remain unchanged.

Then, you can turn on the "wireless function" in the "wireless router" (please see the manual for specific operations), you can use various WEP encryption (as long as it is supported), set it the same on the notebook, and you can receive it.

You can also connect the WAN port, then your "wireless router" needs to be set up separately;

1. Set the WAN port to your original (or assigned to you, or automatically assigned IP) IP, set it to a fixed IP for a long time, if someone else's router turns on automatic IP assignment, you can also use automatic acquisition.

2. You connect the network cable first, use the default IP, username, and password access of your wireless router, turn on the "wireless function", set WEP encryption, and then set the wireless network card to the same IP segment and WEP to use.

According to your situation, add a wireless router and put it in your home, and use the wireless router as a "wireless switch".

Specific: 1. Any LAN port of the wireless router is connected to the network cable (the one that used to be connected to your computer), and there is no need to set it.

2. Your computer is connected to a LAN port of the wireless router.

3. (New) For computers with wireless network cards, use automatic IP acquisition, (or set IP address, gateway, i.e. LAN port address of wired router).

In addition, the transmission distance of a wireless router varies depending on the performance of the machine. As long as the distance is within 50 meters, it can be transmitted, but if you need to penetrate the partition wall in the middle, the signal may be very poor or even not received.

Therefore, it is better to place both the computer and the wireless router next to the window.

Just replace the wired one with the wireless router.