How do I set up my wireless router to connect?

How to set up a wireless router.

How to set up a wireless router.

Wired connection: The wireless router LAN 1 port pulls a network cable over and connects to the WAN port of your wireless router 2. Before connecting your home wireless router2; You first go to the network parameter settings of wireless router 2 and change the address of the LAN port to; After changing DHCP to not enable.

Later, you have to enter the wireless router 2 and enter it in the address bar!

Wireless bridging. It's easy to say; The first wireless router fixed channel number; a second unlimited router; In the network parameter settings, the LAN port is set to;

Reboot into the second wireless router; Turn on WDS in the wireless settings and click Scan; Connect the first wireless router in the result.

Turn off DHCP; Change Start to Not Star.

You have to connect with a network cable, and then set the IP of the second router to be different from the IP of the first router, for example, if both routers are , one of them must be set to non, which can be.

Router to wireless router, second router setup, there are two ways (provided that the first router has been set up):

The first method: dynamic IP mode (the first route is the primary route, and the second route is the slave route).

1. Plug in the router and do not connect the LAN port of the main router first, and reset the slave router (restore the factory);

2. Connect the computer from any LAN port of the router to enter the settings page;

3. Set according to the dynamic IP;

4. Then set the SSID, encryption method and password;

5. Save and restart;

6. After setting, connect the network cable from the LAN port of the main router to the WAN port from the router.

The second method: wireless AP mode.

1. Connect the computer to the LAN port of the router first, and change the IP address of the slave router. For example, most router addresses are, we just need to change from router IP address to that;

2. Turn off the DHCP function from the router in the settings;

3. Finally, connect the network cable from the main router to the LAN port of the slave router (any one is fine), note that it cannot be the WAN port.

Two routers connected:

1. Wired connection, 1, plug the network cable into the LAN port of the secondary router and connect to the computer to set the LAN port IP address to assign one of the IP addresses to the main router, or wirelessly set the IP address of the LAN port of the secondary router to assign one of the IP addresses to the main router, turn off the DHCP service of the secondary router, and finally connect the network cable to the LAN port of the main router.

2. Plug the network cable into the WAN port of the router, connect the router and set the router to access the Internet as an automatic IP address or a fixed IP address.

Second, wireless connection, the router has a bridging function, and the secondary router can directly bridge the main router.

Plug the network cable into the WAN port of the router first, and then connect the LAN port of the router to the computer.

Then enter the account name and password (there is also a hint of raw data on the back of the router) OK.

After entering the settings interface, follow the setup wizard and you can surf the Internet normally.

If it is abnormal, you may wish to click the reset button of the router and set the router again. Drawings:

Do you want to use two routers in series?

1. Connect the cable that comes out of the ADSL cat to the WAN port of your router, and the remaining LAN port can be connected to your computer.

2. Then set your IP address to the gateway as the IP address on the back of the router, the subnet mask, and the IPD address is between the NMS 2---255 on the back of the router or automatically obtain the IP

3. Then open the IE browser, enter the IP address on the back of the router in the address bar, and press Enter. The screen prompts you to enter the username and password, fill in the default username and password of the router are admin, other routers can refer to the manual.

4. After enterprising, the setting wizard will pop up, if it doesn't pop up, it doesn't matter, click "Setup Wizard" in the navigation blue on the left, and the wizard welcome message appears on the right, click "Next".

5. Select "ADSL Virtual Dialing (PPPoE)" and click Next.

6. Enter the username and password, which are the username and password you use when dialing with ADSL.

7. Click Finish

How do I set up a wireless router? WAN and LAN ports are key.

Most users who have been in contact with broadband routers know that there are WAN ports and LAN ports on broadband routers. Broadband routers have such a feature in the working process: the data flow from LAN to WAN direction is not restricted to pass through the router by default, and cannot pass through from WAN to LAN direction by default.

Note: The wireless access part of the wireless broadband router belongs to the scope of the LAN) That is to say, by default, the data packets sent from the computer in the LAN network enter the LAN port of the router, and can be sent out from the WAN port smoothly through the router, but after the data packets from the WAN end enter the WAN port, the router does not let those data packets pass through by default.

Through the actual test, in fact, the network cable connected from the wired router can be connected to the WAN port and LAN port of the wireless router to realize the use of wireless network.

Note that the premise of this article is that you have a network cable that is connected from a normal wired router; This network cable is connected to the WAN port of the wireless router through static IP, such as connecting to the LAN port of the wireless router, that is, the wireless router is used as a wireless AP. The following describes the two connection methods:

The devices are: TP-Link R460 for wired router and TP-Link WR541G for wireless router. So the first way to connect is:

The WAN port connected to the wireless router is the TP-Link R460 LAN port --- the WR541G WAN port

TP-Link R460 LAN port --- WR541G LAN port.

How do I set up a wireless router? First, connect the WAN port of the wireless router.

The WAN port of the wireless router is the TP-Link R460 LAN port --- the WR541G WAN port (here it is assumed that the LAN port of the TP-Link R460 adopts the default IP address, that is, you can enter the TP-Link R460 router settings, and the TP-Link R460 has been set up normally and can access the Internet).

First of all, use a network cable to connect the LAN port of the wireless router (WR541G) on a computer, and enter the setting interface (the default is also, other wireless routers, according to the actual default IP address); First, enter the LAN interface in the TP-Link WR541G wireless router, set it to, and then save and restart the router, at this time, the default IP of the TP-Link WR541G wireless router will be changed to.

The WAN port of the wireless router is connected to the LAN port of the previous router, and the connection mode is selected as static or dynamic IP. If you want to set up a wireless routing gateway for a static IP address, it must be in the network segment of the previous route.

Just connect the network cable, my colleague is connected, just plug in the network cable.

Wired connection: Pull a network cable from the 1lan port of the wireless router and connect it to the WAN port of your wireless router 2. Before connecting your home wireless router2; You first go to the wireless router 2 network parameter settings, and change the address of the LAN port scale; After changing DHCP to not enable.

Later, you have to enter the wireless router 2 and enter it in the address bar!

Wireless bridging. It's easy to say; The first wireless router fixed channel number; Minute sleeps on two Infinite Routers; In the network parameter settings, the LAN port is set to;

Reboot into the second wireless router bridge and/and/her; Turn on WDS in the wireless settings and click Scan; Connect the first wireless router in the result.

Turn off DHCP; Change Start to Not Star.

I'll give you references.