BMW 116 tire pressure ABS and anti skid lights are lit at the same time

1.Generally, there are the following situations: rapid air leakage, high pressure, low pressure, high temperature.

The indicator light is based on the tire pressure and other problems to the owner of a pre-type, perhaps in the process of driving there are potholes, the tire force is different, the tire pressure changes, the indicator light will also be on.

2.The tire pressure light is not on, and before starting the car, you should check it first to see if the tire pressure detector is normal. When the car is in trouble, if the tire pressure monitor does not alarm in time, it is a problem with the tire pressure monitor; If the ignition switch is on start, the indicator light point and the TPMS indicator light will be on at the same time for 2s and then turn off.

In this case, either the original receiver of the vehicle has not been learned, or the receiver controller has been replaced, and the receiver controller has not been learned. You can go to the 4S store and ask professionals to use handheld learning tools to re-obtain all tire sensor IDs and bind the receiving controllers.

3.But if the ignition is played from OFF to START or ON, the indicator light does not illuminate. Then this situation is the failure of the instrument indicator, for the sake of safety, you have to go to the 4S store to ask professionals to check the instrument, if the meter is damaged, the instrument needs to be replaced.

Hello, this should be the ABS wheel speed sensor is damaged, causing the two fault lights to stay on.

This situation occurs because the tire pressure of the car tire is abnormal, resulting in the internal code of the electronic control device is garbled, and there is a failure, you can use the diagnostic instrument to read the fault code or go directly to the 4S shop to find a professional to repair, in this case, do not continue to drive, it is very dangerous.

How to return to the book when the disc light, anti-skid light, and tire pressure monitoring light are on, there are two situations, one is that the tire pressure is lacking, so it causes the wheel speed.

Poor, the same system will judge another wheel has slippage, and the steering wheel has deviated, so these lights will be lit, the second is caused by the dirty engine throttle, because the power output of the engine is not proportional to the torque of the vehicle transmission, so it will report the fault code of the chassis, it is recommended to find a tire shop to balance the tire pressure, and then check the chain to roll the shed Sakura throttle, if you find that it is dirty, you can clean it in time.

In this case, if it is a Volkswagen model, it is generally mainly caused by a problem with the ABS sensor. Because the rubber-type of Volkswagen is used to detect the tire pressure signal through the ABS sensor, so if the three lights of the ABS anti-slip light and the tire pressure light are turned on at the same time, the difference between the beams and the ABS sensor itself is a problem.

You can drive to the repair shop to do a fault detection, see which one is next to the tire of the ABS sensor is broken, and then replace it, the normal replacement of the ABS sensor is about 120.

Questions. The 4S shop said that the ABS master pump was broken and needed to be replaced, is this the reason?

If it is said that there is a problem with the ABS master pump, then it is also possible, but the common one is generally the question of the sensor, and it is necessary to do a fault detection to see.

Questions. Thank you.

Generally, the main pump is not easy to break.

Because the ABS master pump and the ABS computer are integrated, if the computer has a problem, there will also be this kind of failure.

ABS master pump and ABS computer are integrated.

So it may be that there is a problem inside the ABS computer, but this change is the assembly, understand.

Questions. Can I fix a computer if it fails?

How much does it cost to replace the assembly if it costs?

This can be repaired, as long as it is not burned inside.

If this is repaired in a 4S shop, it will be around 2000-3000.

If you replace it in an outside repair shop, it is normally around 1500-1800.

Questions. The 4S store said it would cost more than 4,000, but I didn't replace it because it was too expensive.

This specific need depends on the consumption of each place, and the charges are different in different regions.

This suggestion can be repaired, and it is good to use the original car without replacement.

After all, it's quite cost-effective to repair.

This situation occurs because the tire pressure of the car tire is abnormal, resulting in the internal code of the electronic control device is garbled, and there is a failure, you can use the diagnostic instrument to read the fault code or go directly to the 4S shop to find a professional to repair, in this case, do not continue to drive, it is very dangerous.

What happens to the disc lights, anti-slip lights, and tire pressure monitoring lights, there are two situations, one is that the tire pressure is lacking, so it causes the wheel speed.

Poor, the same system will judge that another wheel has slippage, and the steering wheel has deviated, so these lights will be lit, the second is caused by the dirty engine throttle, because the power output of the engine is not proportional to the torque of the vehicle transmission, so it will report the fault code of the chassis, it is recommended to find a tire shop to balance the tire pressure, and then check the throttle, if you find that it is dirty, you can clean it in time.

Summary. If there are three faulty lights, because all three faulty lamps are related. Check the tire pressure first, if the tire pressure is normal, then you need to check the tire pressure control module to see if there is a problem.

If there is a problem, then it needs to be replaced, if there is no problem, then you need to check the ABS pump, ABS sensor, and ABS control module to see if there are any problems. These aspects need to be specifically examined.

Hello, don't worry, I can ask for your question, but wait a minute, I need text for about 2 minutes.

This refers to the three faulty lamps, because all three faulty lamps are related. Check the tire pressure first, if the tire pressure is normal, then you need to check the tire pressure control module to see if there is a problem. If there is a problem, then it needs to be replaced, if there is no problem, then you need to check the ABS pump, ABS sensor, and ABS control module, and see if there is a problem.

These aspects need to be checked in detail.

The reason why the ABS lights and anti-skid lights and tire pressure lights of the car are on is: the situation caused by the failure of the car's electronic control devices.

The solution is: go to the 4S shop of the car or a professional car repair shop in time to check the electronic control device of the car, and use the computer to check the electronic control of the car**, which can solve the problem of the ABS light on the car.

The anti-skid system is usually turned on by default on the vehicle and does not need to be manually operated. If the car is equipped with ESP or other forms of anti-slip system, the manufacturer will generally set a control switch button on the vehicle, as long as a short press can turn off the ESP, and at the same time the ESP indicator light on the dashboard will be on, if you want to turn the ESP back on, then short press again.

The ABS light and anti-slip light are on because the sensor is broken. The sensor is broken, if there is navigation, it may be that the tires may be skidding due to navigation interference, and the car determines that the vehicle may be out of control. Use the computer to check the ABS sensor to eliminate the fault, and solve the ABS lamp, and the anti-slip light will not be lit.

A solid ABS light indicates an anti-lock braking system alarm. Under normal circumstances, the light will turn on when the ignition switch is turned on or the engine is started, and the system enters the automatic detection program, and after the detection is completed, the light is turned off. If the light does not turn on after turning on the ignition switch, or does not go off after it is on, or lights up while driving, it indicates that the system is faulty.

There are two possibilities for a system to fail:

1. If only the ABS warning light is on while driving, it means that there is a fault in the ABS system, but the car is still reliable and the conventional braking system brakes, and professionals should be asked for maintenance as soon as possible.

2. If the ABS warning light and the braking system warning light are lit at the same time during driving, it means that both the ABS and the braking system are faulty, and the braking characteristics will be mutated. If the latter is the case, you must stop the driving immediately, check the brake fluid level, and if the fluid level is at the "min" mark, you must not continue driving, and you must have a professional service.

If the liquid level is normal, it indicates that the ABS system may fail, that is, the adjustment function of the ABS system fails, and only the ordinary braking system plays a role, which is easy to cause the rear wheels to lock up quickly when braking, resulting in side skidding. At this time, you should drive with caution and carry out repairs as soon as possible.

This is when the tire is punctured and the tire pressure monitoring lights up. The tires are out of pressure, and the car is prone to deviation, side slip or roll over, so the anti-side skid system comes into play, and his lights naturally turn on. The anti-skid lights are on to indicate that the feature is working and the car is slipping.

This happens because the tire pressure of the car's tires is not normal, resulting in the internal coding of the electronic controlsGarbberish, there was a malfunctionYou can use the diagnostic instrument to read the fault code or go directly to the 4S store.

It is dangerous to find a professional to fix it, and not to continue driving in this situation.

There are two situations, one is that the tire pressure is lacking, so it causes a difference in wheel speed, and the system will also judge that another wheel has slippage, and the steering wheel is deviated, so these lights will be lit.

The second is the engine throttle.

Dirt is caused by the power output of the engine and the vehicle transmission.

The torque is not proportional.

It is recommended to find a tire shop to balance the tire pressure, and then check the throttle, and clean it in time if it is dirty.

Anti-slip lights stay on.

1. By mistake, press the close button of ESP.

2. The sensor terminal is loose or malfunctioning.

3. Line short circuit or related fuse.

Fusing. 4. Poor signal transmission caused by software problems.

5. ABS pump body failure.

This happens because the tire pressure of the car's tires is not normal, resulting in the internal coding of the electronic controlsGarbberishIf there is a fault, you can read the fault code with the diagnostic instrument or go directly4S shopIt is very dangerous to find a professional person to repair it, and not to continue driving in this case.

There are two situations with steering wheel lights, anti-slip lights, and tire pressure monitoring lights.

One is that the tire pressure is lacking, so it causes a difference in wheel speed, and the system will also judge that another wheel is slipping, and the steering wheel is deviated, so these lights will be lit.

The second is the engine throttle.

Dirt is caused by the power output of the engine and the vehicle transmission.

The torque is not proportional.

Therefore, the fault code of the chassis will be reported, and it is recommended to find a tire shop to balance the tire pressure first, and then check the throttle, and clean it in time if it is found dirty.

The reason why the anti-slip lights are always on.

1. Mistakenly press the close button of the ESP.

2. The sensor terminal is loose or malfunctioning.

3. Line short circuit or related fuse.

Fusing. 4. Poor signal transmission caused by software problems.

5. ABS pump body failure.