What kind of job can a person who has studied UG styling find?

ug: My high school classmates are now painting glasses frames in Wenzhou - it seems to be pretty good.

I wanted to leave it for other people's sofas, but no one came to see them for a long time.

Hehe, Jiangyin, I didn't use any of the proe modules I learned, or I was defeated by CAD.

Replying to baiduren97's post wouldn't it, right? Mold factories are generally three-dimensional modeling, and it is impossible to use CAD. You didn't find the right one.

Personally, I don't think there's much future in terms of styling (CAD, CAM) alone, CAE is promising. He's just a tool, and he's got to use it flexibly!

Step 2, install UG's best partner - excellent product plug-in, we use it a lot in the later stage, such as program sheet, discharge diagram, automatic programming, etc. The installation method is also very easy, so we put it on.

Step 4: Set up the toolbar we need to use in programming, whether it is modeling, machining and drawing environment. Organize it, and we hide it if it has nothing to do with programming.

Step 5, we go to draw a sketch, that is, a 2D diagram (draw a line, arc, rectangle, trim, translate a line, etc.) only learn the commands that need to be used in the future for programming, plus drawing examples.

Step 6, start the programming operation command explanation, draw two open connection lines, we will program it for a 2D toolpath. The processing methods are: 1. Normal cutting single tool path, 2. Pair.

In-line cutting single-tool toolpath, 3, round-and-forth cutting single-tool toolpath, 4, previous oblique down-knife cutting toolpath, 5, single-tool toolpath offset toolpath, an explanation of how to use and set up.

Step 7, linear closed area 2D toolpath explanation: draw a rectangle, we routinely program it, the commonly used processing methods are: 1, single-line conventional cutting milling toolpath, 2, single-line spiral cutting.

Toolpath, 3, single-line oblique downward cutting toolpath, 4, rectangular internal groove cutout, 5, clear the corner area after the groove is rough. Explain how they use and set it up.

Step 8, call in the existing part diagram (2 cases are updated regularly in the later stage), carry out the actual 2D programming, post-processing, program list, and explain a sequence of knitting parts and margin feed settings. Focus.

Explain the precautions.

Step 9: Learn the use of UG drawing solid (building 3D): sketch extrusion, fiber embedded building rectangular solid, cylinder, chamfered C corner, body draft, offset surface, replacement surface, patch surface, mesh surface and other programming related commands.

In addition, a drawing case is added.

Step 10, start 3D programming command explanation: 1, build a boss to open rough machining, 2, build a straight angle to open the second rough clear angle processing, 3, milling plane processing, 4, build a Qusen vertical surface to climb surface processing, 5,

Build an inclined steep surface to contour processing, 6, build a valley and we go to the root processing, 7, write the workpiece number for lettering, 8, build a hole for drilling and other cases.

Step 11, call in the 3D part diagram for all-round programming and processing (2 cases are updated regularly in the later stage), and transfer in the mold 3D diagram for the whole process programming and application explanation (2 cases are updated regularly in the later stage).

Step 12, another task of CNC mold programming - ug electrode removal (2 cases are updated regularly in the later stage), explain in detail the removal of copper males, spark bit settings, material orders, discharge diagrams, and export copper males.

Methods and details.

Step 13, copper male programming operation: deduction of spark (three methods to deduct the spark position explanation), ordering.

Step 14, individual copper male needs wire cutting, we out of the wire cutting drawing to the processing department.

When I started my apprenticeship as a designer, the apprentice salary of mold design and plastic mold was about 1800 in Jiangsu.

After March, he jumped to Mingfan Silver 2000 and worked again, 4000 in Qingdao in March, and 5000 in Nanjing in March

Now in Shanghai 6000 this is my case.

As far as I know, the salary of this mold design is generally not very good, and the 3-year work experience is only about 4000.

More than 5 years of about 6000, but also depends on the location, the Pearl River Delta that has too many mold designs, and the salary is relatively low.

The Yangtze River Delta may be doing mold design, and at present, the salary is considered to be a high banquet.

There is also a look at their own ability, in short, I heard the masters say that this mold is in this line, whether it is design or fitter, it is a year.

It's better to be a little higher than the salary of ordinary workers in a year.

The introduction of UG is as follows:

ug's programming ideas:

The overall idea of programming is a clever way to do more with the least amount of life. You can achieve the realm of using UG easily and easily. It is to let others see that your knife path is concise, beautiful and fast.

It is to let you experience the great creativity, flexibility, and happy sense of accomplishment that UG brings to you.

Knowledge Extension:

You must use your own brains to think about problems, and you must not be a toddler and follow suit.

It doesn't matter if you study in school, look for information on the Internet, or buy books or video tutorials to study. A little bit of a question to ask, meet a lot of people on the Internet, send a file to him, the file through QQ after the compressed file into RAR format, just ask why can't you open? To be remotely assisted, and do not know what remote assistance is.

Just follow what you want to do - this is the most hidden taboo in learning! (Of course, you have to do this initially, but in the end, you have to understand: what is the essence of this?)

What is its soul, its essence? Through this example or parameter explanation, can you draw inferences and use them flexibly? ）。

I have to ask every little question, and I don't have my own independent ideas at all. Lack of global control. This will tell you unmistakably that you will never learn!

Over-reliance on practice.

People who think this way are the most matched. Some of their thoughts were told by their fellow villagers and friends, and some of them came up with by themselves. It is true that practice is the only criterion for testing truth, and no theory can replace it, but you must not forget this fact

Practical experience is accumulated little by little.

Go to the factory as an apprentice, learn slowly, and there is no hurry to have time.

Many people want to do this, how good it is to go to the factory and have a master to teach and practice this learning model. Indeed, this model worked around the year 2000. Now the talent multi-file refers to the fact that many factories also understand that asking for free apprenticeships will eventually bring a lot of losses to the company, and the cost of training a CNC engineer in a factory is too high.