How do I open all the Internet ports at home?

You need a router, connect the cat and the router with a network cable (connect the router WAN port), and then connect the network cable from the router to the computer in the living room and the computer in other rooms.

If every port is open, there should be a box for the cat, open the box, install the router at the wiring of the cat, and the cable end of each network end is there.

2.You can add a switch, and when you decorate the wiring, you will lay out the wires, and the connectors are in a small box with weak current, on a wall in your home. You'll need to buy a small switch and plug it in.

3.If it is a port on the wall, then make an appointment with the operator (Telecom, Unicom) to continue the installation, if you are opening a network port and want to share the Internet of the whole family, then buy a wireless router.

If it's a network cable. Then only one computer can access the Internet at any one time. Other computers do not have internet access.

Unless each network cable interface is a separate network cable. And there needs to be a place where multiple network cables are concentrated, and the interface of each room can be connected to the network cable through a router or switch to ensure that multiple computers can access the Internet at the same time.

You can directly change the network cable of the telecom, so that the network cable in the home is connected to the network cable in the living room. Then move the cat in the study to the living room and install a wireless router in the living room near the center of the house. You'll be able to access the internet via wifi throughout the house.

1. Install additional ports through a communication company.

2. Increase ports by adding network cables and using routers.

How do I install a router?

01First, connect the WAN port of the router to the LAN port of the optical modem with a network cable. In this way, a transmission can be achieved.

02 After the connection, use the same method. Connect one end of the network cable to the LAN port of the router, and the other end to the network cable interface of the computer.

03After connecting, connect the power supply of the router to the router and the large socket to the power plug board.

04 Then open the browser on the computer, enter the IP address of the router in the browser web page input field, and enter the router. Both the router's IP address and password can be viewed on the back of the router on its own.

06On the network mode selection screen, select Let the router get it automatically, and then click Next.

07On the wireless settings interface, select the encryption method according to your own concept and enter the wireless password. When you're done losing, click Next.

08 When we click Next to finish, a Finish option will appear on the interface. Finish in the bottom right corner to save all the settings.

09 If the IP address of the router is not the same, you can directly surf the Internet, if so, click on the network parameters in the upper right corner. Next, click LAN port settings. In the AP panel that appears on the right, change the original IP address, and you can go online.

Possess the following things: router crystal head network cable crimping pliers to see if the internal line of the network cable socket in the room is ready? I didn't play well according to the T568B standard. Set up your router and you're good to go.

The one on the right is Tianyi's light cat, right? It's not very simple, you have to know which one of the wires below is the wire in your study, and make sure that you can insert the head into the LAN port. How big is your home?

300 square meters? Basically, the house within 200 square meters will not attenuate the signal no matter how you pull the wire, okay?

Install a better wireless router.

Buying a wireless router will do the trick.

If the LAN cable to the other rooms is ready, you can connect to the LAN of the router. Then each room port can be connected to the Internet. If the crystal head is not done, then you can call the computer store to do it for you, it doesn't cost too much money, it's worth it!

Since you don't want to use a router, you can buy a two-way (usually a few dollars), and then enter the main line and go to the location of the line of each house, and make the main line and the line of each house at the summary point of each house into a network cable head, so that you can connect the line of which room with the main line with two links if you want to use it in which room.

Note, however, that this can only be used in one room at a time. To use the room, you must go to the line summary point to plug in the network cable.

Two links are just that. The scientific name is Network Feedhead.

You see if the router has a lot of network cables connected to each of your rooms, if so, you can set up a local area network, it stands to reason that as long as a computer can access the Internet, the rest just need to configure the IP.

Cause Analysis:

The broadband of the community is fixed by the operator, for example, the community is fixed with the Great Wall broadband or fixed is Unicom, and the entire floor-to-home line is controlled by the operator, and the telecommunications personnel can only add lines to access the household, and cannot access the inherent line of the corridor to the household. The broadband port of each room is actually the terminal of the inherent operator. In your home, it doesn't belong to you.

Two ways: 1. Wiring at home.

2. Change the operator.