What is the training sequence and skills of subject 2, and what is the training order of subject 2

Updated on Car 2024-03-14
12 answers
  1. Anonymous users2024-02-06

    Subject 2: Steps to get on the bus:

    Prepare for subject 2 and memorize the mantra to prepare for the subject 2 exam, which can make you have no omissions in the preparation for the subject 2 exam, and also relieve your nervousness, so as not to think nervously as soon as you get on the bus** did not do it properly, so as to avoid panic before the exam starts.

    Subject 2: Steps to get on the bus (five major pieces, rote memorization should also be memorized): one tune backrest; before and after the second tone; Three tones of high and low; Four-tone rearview mirror; 5. Wear seat belts.

    Subject 2 has a great relationship with the driver's sitting posture, and the difference in the front and back of each seat will greatly affect the difference in the position; Adjust the rearview mirror, especially the rearview warehouse; The clutch should be well controlled, the foot can not be stepped on all the time, and when the steering wheel needs to be killed, the clutch can be lifted slightly.

  2. Anonymous users2024-02-05

    Finding the right spot is key: everyone has different heights and physiques, so naturally the points will be different. For example, right-angle turns to see the front cover of the car, when the line is covered, the steering wheel is immediately killed, the tall one has not seen the cover line, and the short one has to be exceeded to hit.

    Be flexible according to your height, try more, and find the right spot.

  3. Anonymous users2024-02-04

    Subject 2 is very rigid, as long as you adjust the position of the seat, you will be able to pass it according to the point and timing given to you by the coach, which is basically some fixed routines. The most important thing is to calm down during the exam, don't be in a hurry, and be sure to adjust the seat position and rearview mirror to the same feeling as when you train, and the angle of the viewing point is different depending on the position. The day before the exam, the coach should take you to the exam room to practice, adjust the position and fix it, and follow the steps of contact step by step during the exam.

  4. Anonymous users2024-02-03

    Subject 2: Practice the car first practice the garage, stop on the side, start on the ramp, turn at a right angle, and drive on the curve. Just remember the location, start slowly, don't be nervous, just don't be nervous.

  5. Anonymous users2024-02-02

    First of all, it is necessary to practice reversing into storage.

    Then to practice side parking. Once we're familiar with these two, it's time to practice ramp stop and start.

    Then make a right-angle turn.

    Finally, you have to practice driving in corners, just like you did in the second test. What is the order of the second training of the department.

    What is the order of sophomore training.

    First of all, you have to practice reversing into the garage, and then you have to practice side parking. Once we are familiar with these two items, we will start practicing the fixed stop and start of the Hunger Tomb ramp, and then make a right-angle turn. Finally, you have to practice driving in corners, just like you did in the second test.

    Can the second practice order be disrupted?

    Don't be disrupted when practicing. After the interruption, there will be a hectic situation during the exam. Therefore, the driving school will practice driving in the order of the test when practicing subject 2, which can reduce the tension of students in the test process and improve the pass rate of the test.

    As you practice, each item in Section 2 has some important points. As long as you memorize and strengthen the exercises completely, there is no problem.

    How long does it take to practice car in Section 2 to take the exam.

    According to the newly revised "Motor Vehicle Driving Training Teaching and Examination Syllabus", subject 2 is examined.

    Before you need to study for 26 hours and the time is 10 days. In fact, it has increased compared to before, so that students can learn to the fullest. The second subject is to practice the car in a separate way, and the exercises are also carried out in order, one by one. After all the projects are completed, the unified exercises are carried out.

    How many points will be deducted for a second slip.

    According to the content of the motor vehicle driver test and measures, if the vehicle skidding is less than 30cm during the test, 10 points will be deducted in the second section, and if the vehicle skidding distance is greater than 30cm, it will be directly judged to be unqualified in the test, and the vehicle skidding will appear at the ramp fixed-point parking and starting items.

    When will the results of the Subject 2 exam be announced.

    The results of the second exam are released in real time at the end of the exam. Points deductions will be reported directly during the test, and the test results will be announced when the last corner is completed. As long as you complete the cornering drive, you have a good chance of passing the test in subject 2, otherwise you will be declared a failure on the way.

    There are several opportunities to take the exam on the day of the subject 2 exam.

    There were two chances to take the exam that day. After failing the first test attempt, the student needs to get out of the car, and the staff of the Post Driving Test Center will move the vehicle to the location where the first test item is reversed, and then the student will start the test again. Never move the vehicle on your own after failing the test.

    What is the order of Ke 2 training @2019

  6. Anonymous users2024-02-01

    The order of the exams for Subject 2 is as follows:

    1. Preparation before the exam.

    1) According to the date of appointment and the number of test sessions, go to the waiting hall 30 minutes in advance to verify your fingerprint and receive the sign-in number.

    2) Wait in the test hall, please pay attention to the hall broadcast and pay attention to the information displayed on the screen in the hall, and the voice prompt tone is "Please take the test from *** to ** car".

    2. Get on the bus and prepare.

    1) Fasten your seat belt, adjust the seat to the usual position of the car, and then adjust the rearview mirror to make it easier for you to see the point.

    2) After confirming with the examiner that you are ready to start the test, you can start according to the voice prompts.

    3) Step on the clutch first, hang 1st gear, turn on the left turn signal, release the handbrake, and then slowly loosen the clutch to semi-linkage, put the brake, and the car moves forward slowly.

    3. The examination has officially begun.

    Reversing into storage. 1) The car drives to the starting position, the distance of the body offline, the body should press the white line in front of the right side of the library, but do not exceed.

    2) After the car enters the garage, the body must be straightened, do not turn left and right.

    3) After entering the warehouse, be careful not to pour too much, and stop at the point.

    4) Do not stop, slip, turn off the engine, or press the line in the whole process.

    Reversing Warehousing Skills**

    Side parking.

    1) The distance between the body and the edge of the library should be adjusted, and the distance between the body and the library should not be too close to the library.

    2) Look at the line when playing the direction.

    3) After entering the library, you should play left steering, and the car can not press the corner of the warehouse when leaving the warehouse.

    4) Do not stop, slip, turn off the engine, or press the line in the whole process.

    Side Parking Tips**

    Curve driving. 1) After the car enters the curve, make a big turn.

    2) The speed of the car should be controlled slowly, and it is best to move forward at a uniform speed, and every corner should be on time.

    3) Do not stop, slip, turn off, or press the line during the whole process.

    Curve Driving Skills**

    Right-angle turns. 1) Straighten the body before entering the right angle, and adjust the distance between the body and the sideline.

    2) When you go to the corner to hit the direction of death, the speed of hitting the direction must be fast, and the clutch should be a little looser.

    3) When leaving the warehouse, it is necessary to return to the right direction when the body is not back to the right, and it is too late to return when the front of the car is back to the right.

    4) Do not stop, press the line, turn off the ignition, etc. in the middle of the test.

    Right Angle Turning Technique**

    Ramp fixed stop and start.

    1) The speed of the car should not be fast when going uphill, and the right wheel of the car should be controlled at 30 cm from the edge line.

    2) When reaching the specified position, the speed of the vehicle should be slower, so that the point can be found.

    3) Hit the left steering before starting and find the semi-linkage.

    4) During the whole process, you can not stop (except for fixed points), slip, turn off, and press the line.

    Ramp fixed-point parking and starting skills**

    Fourth, the end of the examination.

    1) If you fail the first chance test, you will take the second test, and the test process is the same as the first time, and it is the same car and the same track, and you must re-verify your fingerprints. Those who fail to pass the make-up exam will need to make another appointment for the exam within 10 days.

    2) Candidates who have passed the examination should leave the examination room quickly, and should not interfere with the examination of others, and finally hand in the materials for signing.

  7. Anonymous users2024-01-31

    Start: After getting into the car, adjust the seat, wear a seat belt, step on the clutch, brake, test gear, play the left turn signal, honk, hang a gear, release the handbrake, gently lift the clutch to the semi-linkage and release the brake, and release the clutch after the car is stable.

    Shifting: the car is stable, point the oil, when the speed reaches 15 miles, collect the oil, step on the clutch, and change the second gear; Loosen the clutch, point the oil, when the speed reaches 20 miles, collect the oil, step on the clutch, change the third gear, loosen the clutch, and point the oil; Collect oil, step on the clutch, reduce the second gear, loosen the clutch; Step on the clutch and reduce one gear.

    Drive in a straight line: Control the speed at 20 miles, look ahead, and hold the steering wheel in a straight line.

    Left and right turns: Pay attention to surrounding vehicles, slow down, turn the steering wheel after turning left and right turn signals for 3 seconds, and turn signals when entering the intersection.

    Pull over: slow down, pay attention to surrounding vehicles, hit the right turn signal for 3 seconds, step on the clutch, brake and stop smoothly when 30 cm away from the side of the road, return to the turn signal, take off the gear, and pull the handbrake.

    Reversing into storage: set a parking space, and reverse the same as the second branch.

    U-turn: Slow down, pay attention to surrounding vehicles, and make a big turn to the right as much as possible.

    Start: After getting on the car, adjust the seat, fasten the seat belt, step on the clutch, brake, hang a gear, release the handbrake, release the brake, loosen the clutch to semi-linkage start, the car starts smoothly and does not shake the clutch, point the throttle, and practice turning the steering wheel with the left hand.

    Shift from first gear to second gear: glance at the tachometer pointer at about 1500, collect oil, step on the clutch, hang the second gear, release the clutch, and point the oil.

    My shortcomings are that my hands are weak and often can't hang up the gear, I loosen the clutch too slowly, and I can't use my left hand as the main steering wheel, so it seems that I need to practice more strength in my legs and hands. No, I'll ride my bike to learn how to drive, and when I have the chance, I'll go to the simulation room to practice.

    The key is to master the speed of the car, to stabilize the clutch, to find a good point, to cooperate well with hands and feet, to know the gear, to step lightly, to find a good manhole cover, a quarter, but also to understand the sound of the car, to have a sense of direction. To stabilize the clutch, the speed should be slow, to be aware of it, to start with a seat belt, hit the left light, hang a first gear, release the handbrake, and honk. When stopping, turn on the right light, press the clutch, step on the brake, pull the handbrake, hang neutral gear, and turn off the engine.

  8. Anonymous users2024-01-30

    The second subject is a practice and test related to practical operation, and the order of his learning to drive is different for each driving school, but in general, it will include well, curve driving, fixed-point parking, reversing into the garage side parking and so on.

  9. Anonymous users2024-01-29

    The order of learning to drive in subject 2 is: reversing into the garage, parking on the side, starting from the slope at a fixed point, turning at right angles, and driving on a curve.

  10. Anonymous users2024-01-28

    There are more subjects in subject two, and normally they practice reversing and entering the warehouse first, because it is the most difficult, so the practice time is longer.

  11. Anonymous users2024-01-27

    The general sequence of the second subject is vehicle familiarization and gear shifting, reversing and side parking, curve driving and obstacle detour, etc.

    1. Vehicle familiarization and gear shifting.

    First of all, familiarize yourself with the various controls of the test vehicle and make the necessary adjustments, such as seats, mirrors, seat belts, etc. Straight-line driving and gear shifting, straight-line driving practice on the field, including starting, accelerating, decelerating and shifting gears, etc., to be familiar with the skills and rhythm of shifting.

    2. Reversing into the garage and side parking.

    Practise reversing and storage skills, including choosing the correct starting point for storage according to the test requirements, mastering the steering method of the steering wheel, and clearly observing and measuring distances. Practise the skills of parking on the side, including choosing the right parking position, mastering the steering wheel steering method, observing and measuring distance, etc.

    3. Curve driving and obstacle detour.

    Practice the skills of driving on curved roads, including controlling speed, steering, and the position of the vehicle, and taking care to keep the vehicle stable. Practice the skills of driving the vehicle around obstacles, including accurately judging the position of the hail foci of the obstacle and the spatial position of the vehicle, and choosing the appropriate time and speed to make the detour.

    Subject 2 Exam Notes:

    1. Preparation.

    Adjust the seats and mirrors. Adjust to your position and condition, and be sure to wear your seatbelt. It may seem like a simple thing, but it's easy to make mistakes when you're flustered and nervous.

    Therefore, it is important to practice several times before the exam to avoid deducting points for this low-level mistake during the exam.

    2. Match the speed of the vehicle.

    Find the right angle and speed when parking in the side direction. When parking, remember to find the right angle, and the steering wheel should turn quickly and react quickly. At the same time, it is necessary to match the speed of the car, otherwise it will cause the parking to deviate from the position, and the deduction of points outweighs the loss.

    3. Stabilize the clutch.

    Stabilize the clutch at the fixed point of the ramp. When starting, pull the handbrake and be sure to release the handbrake with the left turn signal. At the same time, it is necessary to stabilize the clutch and release the clutch while stepping on the accelerator to avoid stalling and slipping.

    This part requires a good balance and needs to be practiced many times to increase skills.

  12. Anonymous users2024-01-26

    First you have to practice reversing into the garage, and then you have to practice side parking. Once you're familiar with both of these items, it's time to start practising ramp parking and starting, and then get into your pants and make right-angle turns. The last practice is cornering, in the same order as the second test.

    Can the order of the secondary train be disrupted?

    Don't be disrupted when practicing. After being disrupted, there will be a rush during the exam. Therefore, when practicing subject 2, the driving school will practice the car in the order of the test, which can also reduce the tension of the students during the test, thereby increasing the pass rate of the test.

    When practicing, each item of subject 2 has some important points, as long as you memorize and strengthen the practice completely, there is no problem.

    2.How long does it take to practice?

    According to the newly revised "Motor Vehicle Driving Training Teaching and Examination Syllabus", subject 2 requires 26 hours of study before the test, and the time is ten calendar days. In fact, it is an increase compared to the previous one, and students can learn fully. The subject Erhu rotten spine is a sub-item exercise, and it is also practiced in order, one by one.

    After all the projects are completed, they will be combined and unified.

    Millions of car purchase subsidies.

Related questions
12 answers2024-03-14

The speed limit passes through the width limit door, and its test requirements are: continuous crossing from 3 doors, the speed is not less than 10 kilometers per hour, and the door suspension rod must not be touched; Scoring criteria: 20 points will be deducted from the bumper bar; Failure to follow the prescribed route and fail; Less than 10 kilometers per hour, failing; If the ignition is turned off, 20 points will be deducted. >>>More

5 answers2024-03-14

1. Before the drill pipe starts, the rider also needs to relax his mind and muscles, and his legs naturally clamp the car body. After the start of the pile, it is necessary to find the angle and speed of the input rod, if the angle is too large or the speed is too fast, it will cause the car body to not have enough steering space and press to the limit width line. The correct approach is to choose to enter from the middle of the sideline and the benchmark in the first or second gear, and after entering, it is necessary to properly cooperate with the oil separation, and try to maintain a semi-linkage state, so that the power output can be cut off in time for corresponding adjustments. >>>More

7 answers2024-03-14

Will teach the inversion first. It's reversing. Some instructors will teach you how to pour, but some will accompany you in the car (if you are a girl). >>>More

10 answers2024-03-14

Press the clutch first, then the brakes, and then remove the gear when the car is stopped.

8 answers2024-03-14

Driving is a journeyman, and cooking makes perfect. Don't just try to be cheap! Find a good instructor to learn to drive! >>>More