How to set the SSD as a system disk when partitioning

1. Before operating, please make sure that the SSD has been installed on the computer and plugged in the data cable and power cable.

2. Press and hold the DEL key to enter the BIOS when the computer is turned on.

3. After entering the BIOS, use the up and down arrow arrows to select System Summary and press the Enter key.

4. Then find SATA DRIVE 0 1 2 to check whether the SSD you installed has been recognized.

5. After seeing the installed SSD, press the ESC key to return to the main interface, use the left and right arrows to select the startup boot settings, use the up and down arrows to select the primary boot sequence, and click the enter key to enter.

6. Use the up and down arrows to select the solid-state drive (SSD) you have installed, and press the "+" button to adjust to the first position (the top position).

7. After adjusting to the first position, press the F10 key to save the settings and exit, a window will pop up at this time, select Yes.

8. The computer is restarted at this time, and the F12 key is pressed non-stop when starting, and a dialog box pops up: at this time, you can see that the installed Intel SSD has been the first boot item, press the Enter key.

1. The partitioning method of the system installed in the mechanical hard disk: the number of bytes occupied by the operating system and all programs installed in one area multiplied by 2 (according to personal preference) is the total capacity of the system partition. The remaining free space, which determines the number of partitions and the capacity of each partition based on usage.

2. Partitioning method for system installation on SSD: After the operating system, drivers and programs are all installed on a SSD, 10% of the free space is passing, and 20% is the best ratio.

Since the system will increase the used space of the system partition all the time, 30%-40% of the free space is reserved. The amount of available space should also be flexibly controlled according to the total capacity of the system partition. Depending on the type of data in which the data is stored, the number of partitions on the HDD and the capacity of each partition are determined.

3. SSDs with a capacity of less than 512G are not recommended to be partitioned.

1. AHCI mode must be enabled in BIOS. Generally, new computers, such as those purchased within 2 years, basically don't care about it, because there is only AHCI mode anymore. If you have an earlier computer, there will be IDE mode and AHCI mode, before installing the system, you can set it to AHCI.

2. Boot up and press del to enter BIOS, enter Advanced, and then enter SATA configuration, press enter on SATA mode selection (or chip SATA type), a dialog box will open, there are IDE, AHCI and other options, if you want to use AHCI, select AHCI.

3. Also, pay attention to 4K alignment. If you install it with a Microsoft CD, format the C drive during the installation process, and it will be directly 4K aligned. If you use third-party software, pay attention to the selection of aligned integer multiples macro hole to 4096.

Solid-state drive, referred to as solid disk, is a hard disk made of solid-state electronic memory chip array, which is composed of a control unit and a storage unit (flash chip, DRAM chip).

SSDs are identical to HDDs in terms of interface specifications and definitions, functions and usage methods, and are completely consistent with HDDs in terms of product shape and size. It is widely used in military, vehicle-mounted, industrial control, first-class monitoring, network monitoring, network terminals, electric power, medical, aviation, navigation equipment and other fields.

Because SSD technology is different from traditional hard disk technology, many new memory manufacturers have emerged. Manufacturers only need to buy NAND memory, and then cooperate with the appropriate control chip, and then they can make SSDs.

Due to the fast read and write speed of the SSD, most users now add the SSD to the computer as a system disk, and the new hard disk is partitioned to install the system, so how to install the system on the SSD partition? Teach everyone the new SSD partition installation system to teach the leakage cleaning process.

PE install win7 original image tutorial。

How to install the original win7 system before the solid state drive is brightened.

1. Preparation for installation

1. Install the SSD on the computer.

2. Operating system: win764-bit flagship version.

G left and right U disk: Make a U disk PE boot disk.

4. Boot settings: Set the boot method from the USB flash drive.

K Alignment Tutorial: SSD 4K Alignment Tutorial.

2. The steps of solid-state hard key to partition the system are as follows

1. Insert the boot USB flash drive into the computer equipped with the SSD, reboot and press the F12, F11, ESC and other hotkeys, select the identified USB flash drive option in the pop-up boot menu, and press Enter;

2. Enter this menu and select Enter to enter the PE system;

3. Open [DiskGenius Partition Tool] on the PE desktop, select the SSD, and right-click [Quick Partition];

4. Set the number of partitions, set the size of the system disk, check [Align partitions to integer multiples of this sector], the sectors can be 2048 or 4096, both indicate 4k alignment, OK;

5. After completing the partition, open [PE one-click installation], select GHO for the image path, and then select the installation location, usually C drive, OK;

6. A prompt box pops up, click Yes to perform the system decompression operation;

7. After completing the decompression, the computer will restart, and the USB flash drive will be pulled out at this time, and the system installation process will be automatically executed;

8. Finally, boot into the new system desktop, and the SSD will be installed on the system.

After the above steps, the SSD will be partitioned and the system will be installed, and users who do not know how to do it can refer to the above steps.