How to use cans to make the wifi signal better at home

Wash the cans and pull out the tabs.

Circumcision of the tank removes the entire bottom.

Cut a portion of the can, leaving 1 to 2 cm at the mouth of the can.

Fan the bottle, turn the can upside down, and place the mouth of the can on top of the antenna of the wireless router.

China Telecom provides the best quality network communication services, old friends for new phones, Internet age cash, 100 Gigabit broadband free experience, ultra-clear TV ITV, 517 telecom activities can be directly queried through the telecom business hall or physical business hall.

Make it in the shape of a trumpet and lie down.

Method: The first step is to wash the can and pull out the pull ring;

The second step is to circumferentially cut the bottom of the tank and cut off the entire bottom;

The third step is to cut a part of the can and leave one or two centimeters at the mouth of the can;

Fourth, cut the bottle into two parts directly opposite the uncut part.

The fifth step is to make the bottle body into a fan shape, put the can body upside down, and put the can mouth of the can on the antenna of the wireless router.

If the wifi signal is not significantly strengthened, it may be that the height of the can is not high enough to exceed the height of the wireless router.

Precautions. It can only boost the wifi signal, not the internet speed. ‍

There are tutorials in the wireless forum, address.

The location of this experiment was selected in Mr. Ren's tea shop, and according to the method provided in the online post, we spent five steps to make a simple can signal amplifier. The first step is to wash the can and pull out the pull ring, the second step is to circumferentially cut the tank to remove the entire bottom, the third step is to cut a part of the can, leaving 1 to 2 cm at the mouth of the can, the fourth part is to reduce the bottle body into two parts on the front façade of the uncut part, and the fifth step is to make the bottle body fan-shaped, put the can body upside down, and put the can mouth of the can on the antenna of Mr. Ren's wireless router.

Hope it helps.

Don't worry if the signal at home is too weak, the can can can be used to enhance the wifi signal.

Here's how to increase your internet speed:

QoS packets can be reset.

Windows XP provides users with a new set of networking programs"Quality of Service (QoS packets).", and when installing Windows XP, the system sets it as a caller by default, reserving about 20% of the bandwidth. In other words, if you don't use QoS, you're losing 20 percent of bandwidth.

In fact, the program is only effective for large enterprise networks, and not for individual users or small business users, especially ADSL users. It's best to disable this program, doing so can increase the speed of your network connection by about 20 percent.

Here's how it should be:

1. Click "Start" - >Run" and enter it in the text box""to start"Group Policy"Utensil.

2. In the tree directory on the left, double-click "Computer Configuration|".Manage templates |Network directory entry, select the QoS Packet Invoker entry.

3. On the right side of the window, click the "Limit Retained Bandwidth" tab item. Select "Properties" to open the properties dialog box, select "Enabled", enter the number "0" in the "Bandwidth limit" box, (note that just disabling it without setting the reserved bandwidth to "0" will not free up the occupied bandwidth), and finally click "Confirm" to exit the Group Policyr.

Putting a can on the router solves the big problem of using the Internet at home, which is really great.

Step Method.

Step 1: Wash a used can with clean water.

Step 2: Remove the pull tab of the can.

Step 3: Circumferentially cut the bottom of the can according to the red line shown in the figure below, and cut off the entire bottom of the can (as shown below).

Step 4: Circumferentially cut the top of the can according to the red line shown in the figure below, it is not necessary to cut it all, only the white line part of the picture below is left, and the white line must be close to the mouth of the can (as shown below).

Step 5: Draw a red line vertically on the reverse side of the white line, and cut off the iron sheet along the red line (as shown below).

Step 6: Make the white wire of the aluminum can partially attached to the base, pass the router antenna through the mouth of the can, and use liquid glue to fix the bottom of the can (as shown below).

Step 7: Everything is OK, do it yourself, have enough food and clothing!

Renderings: