Buick Excelle 1 6 Fault Code P1626 Solution?

Buick Excelle fault code P1626, is to indicate that the engine cooling system is missing antifreeze, need to add antifreeze, Buick Kaiyue to add antifreeze specific operation steps are as follows:

1. Open the driver's door of the Buick Excelle.

2. Pull the hood switch of the Buick Excelle.

3. Lift the engine hood of the Buick Excelle.

4. Slowly unscrew the lid of the small kettle of the Buick Kaiyue water tank and release the internal high-pressure gas.

5. Fill the small kettle of Buick Kaiyue with cooling water to the max position.

Notes:Another key to choosing antifreeze is to ensure safety. Advanced antifreeze has the effects of anti-corrosion, anti-scale, anti-boiling, anti-freezing, anti-rust, etc., and can also protect the water tank well, and can be used all year round.

The appearance of high-quality antifreeze should be clear and transparent, and have eye-catching color, no peculiar smell, and some inferior antifreeze does not have the function of antifreeze and prevent boiling, although some antifreeze is qualified for freezing and boiling point, but it is corrosive, and can "bite" the water tank and pipeline, affecting driving.

The meaning of Buick Excelle P1631 is that the vehicle's anti-theft system is locked, the vehicle enters the anti-theft mode, the vehicle reports a permanent fault code, and the vehicle can not start, this situation needs to be solved by reuniting the vehicle's key with the anti-theft system, the specific operation steps are as follows:

1. Press the driver's door lock button of the vehicle.

2. Plug and unplug the car key 6 times in a row.

3. Turn the car key when inserting the key for the sixth time to turn on the power bibyside source.

4. At this time, the door lock will be unlocked, press and lock the door again.

5. Then press the unlock button of the remote control to complete the matching.

Summary. F1: Poor contact with the water level sensor.

E1: When the drainage is overtimed, check whether the drainage pipe is blocked.

E2: The lid is not properly covered.

E3: The dehydration is unbalanced, shake the clothes again and dehydrate againE4: The water inlet is overtimed, check the water pressure, and whether the water inlet valve is dirty and blocked.

E5: The water temperature exceeds 50 degrees Haier automatic washing machine failure**.

F1: The water level sensor of Haier washing machine is not in good contact.

E1: The drain of the Haier washing machine is overtimed, check whether the drain pipe is blocked.

E2: The lid of the Haier washing machine is not properly covered.

E3: Haier washing machine is unbalanced in dehydration, shake the clothes again and spin them again.

E4: When the water inlet of the Haier washing machine is overtimed, check the water pressure and whether the water inlet valve is dirty and blocked.

E5: The water temperature of Haier washing machine exceeds 50 degrees.

E6: Does Haier washing machine use high-foam laundry detergent Little Swan automatic washing machine failure** display"e0"Power failure alarm.

Display"e1"Alarm for water ingress or water replenishment for more than 1 hour.

Display"e2"Drain time more than 5 minutes to alarm.

Display"e3"Before dehydration (including after the appointment is activated), the door is not closed to alarm.

Display"e4"Three consecutive barrel collision alarms.

Display"e8"Water level sensor alarm.

What does the Buick P1467 fault code mean?

Hello, I am helping you with your inquiry.

We'll be happy to answer for you; Check the activated carbon canister solenoid valve and related pipelines and carbon canisters to see if there is any air leakage in those pipelines. There is also the fuel tank cap to see if there is any air leakage. Can the current fault code be cleared?

Do you have any other questions? If you are satisfied with my service, please give a review, what does it mean to show the failure of the blowing machine?

F1: Poor contact of the water level sensor E1: Drain timeout, check if the drain pipe is blocked E2:

The upper cover is not covered well E3: The dehydration is unbalanced, shake the clothes back up and dehydrate again E4: The water inlet is overtimed, check the water pressure, whether the water inlet valve is dirty and blocked E5:

The water temperature exceeds 50 degrees Haier automatic washing machine failure**F1: Haier washing machine water level sensor is in poor contact E1: Haier washing machine draining timeout, check whether the drain pipe is blocked E2:

The lid of the Haier washing machine is not covered properly E3: The dehydration of the Haier washing machine is unbalanced, shake the clothes again and dehydrate them again E4: The water inlet of the Haier washing machine is overtimed, check the water pressure, and whether the water inlet valve is dirty and blocked E5:

The water temperature of Haier washing machine exceeds 50 degrees E6: Does Haier washing machine use high-foaming laundry detergent Little Swan automatic washing machine failure** display"e0"Power Failure Alarm display"e1"Water inlet or water replenishment for more than 1 hour alarm display"e2"Drain time more than 5 minutes to alarm. Display"e3"Before dehydration (including after the appointment is activated), the door is not closed to alarm.

Display"e4"Three consecutive barrel collision alarms. Display"e8"Water level sensor alarm.

Do you have any other questions? If you are satisfied with my service, please give me a review

Hello, what you said about this fault code is. If the ignition power supply is less than 10 volts, it is necessary to check whether the circuit is falsely connected. As well as checking if the fuse is blowing?

The car master is here to help.

P1682-00 Buick what fault code.

After the accident is repaired, the computer reports P1682-00 Ignition 1 Circuit 2 cannot start, hello. I am your exclusive technician, attentive, careful, attentive to answer your questions, I hope this service can help you. Hello, what you said about this fault code is.

If the ignition power supply is less than 10 volts, it is necessary to check whether the circuit is falsely connected. As well as checking if the fuse is blowing? Ignition coil, power supply needs to be checked.

The fault of Buick Kaiyue P0128 is that the cooling system is not well circulated, and the medium is insufficient, that is, the cooling water of the cooling system of the vehicle engine is insufficient, resulting in poor circulation, and the specific operation steps are as follows:

1. Open the driver's door of the Buick Excelle.

2. Pull the hood switch of the Buick Excelle.

3. Lift the engine hood of the Buick Excelle.

4. Slowly unscrew the lid of the small kettle of the Buick Kaiyue water tank and release the internal high-pressure gas.

5. Fill the small kettle of Buick Kaiyue with cooling water to the max position.

The meaning of Buick Kaiyue P1631 is that the vehicle's anti-theft system is locked, at this time the vehicle enters the anti-theft mode, the vehicle reports a permanent fault code, and the vehicle can not start, this situation needs to be solved by re-matching the vehicle's key with the anti-theft system, the specific operation steps are as follows:

1. Press the driver's door lock button of the vehicle.

2. Plug and unplug the car key 6 times in a row.

3. Turn the car key to turn on the power when the key is inserted for the sixth time.

4. At this time, the door lock will be unlocked, press and lock the door again.

5. Then press the unlock button of the remote control to complete the matching.

P1631: Anti-theft password input error (GM). The anti-theft system of the car is locked, how can it be possible?

How is it possible to clear the fault code? You must use the car computer detector, enter the blocker system (the car anti-theft is in the blocker system), redo the key programming (enter the password), and match the key.

Use the car computer detector, enter the blocker system (the car anti-theft is in the blocker system), redo the key programming (enter the password), and match the key!!

P1631: Anti-theft password input error (GM).

This is a common problem of Buick Kaiyue. Automatic transmission ECT failure, solenoid valve failure, shift switch failure.

1. The flashing of the hold light is the gearbox fault alarm, and the engine fault light is the version because the gearbox ect requests the engine fault light to light up to indicate that the car is faulty.

2. In this case, the basic lock is the electronic components, the reason is that the car now has a self-test system, which can detect the fault of the engine and transmission electronic components themselves (through the data value), if the electronic components work abnormally, the computer will record the fault**.

3. If it is a mechanical failure, it needs to be detected and judged by the maintenance personnel.

Hello! The condition for setting the fault code is that the transmission control module detects a fault in the engine speed signal within 2 seconds.

The causes of failure are: engine module, transmission module, and wiring harness between them. [If you have a problem with the car, ask the car master.]

4S shop professional technician, 10 minutes to solve. 】