Motherboard alarm 1 short 3 long, ASUS motherboard alarm 1 long and 3 short, what s going on?

There may be a memory parity error. You can go to the CMOS settings and turn off the memory parity option, that is, set it to disabled. However, in general, the memory module has parity and turns on parity in the CMOS setting, which is good for the stability of the microcomputer system.

The approximate alarm is 1 long and 3 short: , which means that the keyboard controller is wrong, please check the motherboard.

1 Short: The system starts normally. This is something we hear every day and it also shows that there is nothing wrong with the machine.

2 Short: General error, please go to CMOS setup and reset the incorrect option.

1 Long 1 Short: There is an error with the RAM or motherboard. Try to change the memory, if it still doesn't work, you have to change the motherboard.

1 Long 2 Short: Wrong monitor or graphics card.

1 Long 3 Short: Keyboard controller error. Check the motherboard.

1 Long 9 Short: Motherboard flash RAM or EPROM error, BIOS corruption. Try a different block of flash ram.

Constant ringing (long sound): The memory module is not plugged in tightly or damaged. If it still doesn't work, you can only replace a memory module.

Ringing: The power supply and monitor are not properly connected to the graphics card. Check all the plugs.

Repeated short rings: Power supply issues.

No sound, no display: Power issue.

Unplug your memory with an eraser and insert it back in. Look.

ASUS motherboard alarm one long and three short causes and solutions:

ASUS motherboard alarm one long and three short is generally a memory error, memory corruption.

Yes: Plug and unplug the memory and change the memory slot location. The memory slot is cleaned, and the gold finger part of the memory is wiped with an eraser.

Plug and unplug the graphics card, clean the graphics card slot, and wipe the gold finger part of the graphics card with an eraser.

If the above methods don't solve the problem, please try:

There has been a prompt sound when the machine is turned on, and it is not started because the contact inside is not good, or there is hardware damage, and it is good if you move it and turn it on again, the contact is not good.

Sometimes it can be turned on and sometimes it can't, and the possibility of power supply is relatively large.

Disassemble the power supply to remove the dust and see if there is any capacitor bulging.

If there is a lot of dust in the power supply, you can put it back in after you clean it and try it.

If there is not much dust, or the capacitor is bulging, it is recommended that you directly change the power supply and install it.

Hello, I am happy to serve you and give you the following answers: 1. The situation where the problem occurs: the host alarm is three short and one long, which refers to the alarm sound issued by the host, three short and one long, each short sound interval is one second, and the long sound is two seconds apart, this alarm sound indicates that the host has a hardware failure.

2. Reasons: 1. The hardware of the host is faulty, which may be the failure of hard disk, memory, CPU and other hardware; 2. If the host system fails, it may be that the system files are corrupted, the system resources are exhausted, etc.; 3. If the power supply of the host fails, it may be that the power cord is broken, the power socket is in poor contact, etc. 3. Solution:

1. Check the host hardware, check whether the hard disk, memory, CPU and other hardware are faulty, and replace the hardware in time if there is a failure; 2. Check the host system, check whether the system files are damaged, whether the system resources are exhausted, and reinstall the system in time if there is a problem; 3. Check the power supply of the host, check whether the power cord is broken, whether the power socket is in poor contact, and replace the power cord or power socket in time if there is a problem. 4. Personal experience and high-altitude tips: 1. The host alarm is three short and one long, indicating that the host has a hardware failure, and the host hardware, system and power supply should be checked in time, and the problem should be found and solved in time; 2. The inspection and maintenance of the host hardware, system and power supply should be carried out regularly to prevent the failure of the host; 3. The inspection and maintenance of the host hardware, system and power supply should be carried out by professionals to ensure the normal operation of the host.

The motherboard alarm sound is one long and two short, which means: the monitor or graphics card is wrong.

When the interface on the motherboard is faulty or the interface is damaged, the motherboard will send out an alarm sound to remind the user that the error is in the place. Depending on the cause of the fault, the type of chirp sound emitted by the motherboard is also different. Specifically, some of the reasons why the motherboard chirps when booting up are as follows:

1. Short negotiation 1: the system starts normally, and there are no problems and failures.

Short: General error, should go into CMOS setup and re-set the incorrect options.

Long 1 Short: There was an error with the memory or motherboard.

Long 2 Short: Wrong monitor or graphics card.

Long 3 Short: Keyboard controller error.

Long 9 Short: Motherboard Flash RAM or EPROM error, BIOS corruption.

Hello, I am happy to serve you and give you the following answers: First, the problem occurs: the host which alarm three short and one long, refers to the alarm sound issued by the host, three short and one long, each short sound interval of one second, long sound interval of two seconds, this alarm sound indicates that the host has a hardware failure.

2. Reasons: 1. The hardware of the host is faulty, which may be the failure of hard disk, memory, CPU and other hardware; 2. If the host system fails, it may be that the system files are corrupted, the system resources are exhausted, etc.; 3. If the power supply of the host fails, it may be that the power cord is broken, the power socket is in poor contact, etc. 3. Solution:

1. Check the host hardware, check whether the hard disk, memory, CPU and other hardware are faulty, and replace the hardware in time if there is a failure; 2. Check the host system, check whether the system files are damaged, whether the system resources are exhausted, and reinstall the system in time if there is a failure; 3. Check the power supply of the host, check whether the power cord is broken, whether the power socket is in poor contact, and replace the power cord or power socket in time if there is a failure. 4. Personal tips: 1. The host alarm is three short and one long, indicating that the host has a hardware failure, and the host hardware, system and power supply should be checked in time, and the fault should be found and solved in time; 2. The inspection of the host hardware, system and power supply should be completed by professional technicians to ensure the normal operation of the host; 3. The maintenance of the host should be carried out regularly to ensure the normal operation of the host and avoid failures.

Hello, I am happy to serve you, for you to make the following answers: 1. The situation of the problem: the host alarm three short and one long, refers to the alarm sound issued by the host, three short and one long, each short sound interval of one second, the long sound interval of two seconds, this key Qingchong alarm sound indicates that the host has a hardware failure.

2. Reasons: 1. The hardware of the host is faulty, which may be the failure of hard disk, memory, CPU and other hardware; 2. The host system fails, which may be caused by system file destruction, system resource exhaustion, etc.; 3. If the host network fails, it may be that the network line is disconnected, the network equipment is faulty, etc. 3. Solution:

1. Check the host hardware, check whether the hard disk, memory, CPU and other hardware are faulty, and replace the hardware in time if there is a failure; 2. Check the host system, check whether the system files are damaged, whether the system resources are exhausted, and reinstall the system in time if there is a problem; 3. Check the host network, check whether the network line is disconnected, whether the network equipment is faulty, and repair the network in time if there is a problem. 4. Personal tips: 1. The host alarm is three short and one long, indicating that the host has a hard and bright keypiece, system or network failure, which should be checked and solved in time; 2. In order to avoid the failure of the host, the host hardware, system and network should be checked regularly, and the problems should be found and solved in time; 3. In order to ensure the stability of the host, the host data should be backed up regularly to prevent data loss.

Hello, I am happy to serve you, and make the following answers for you: Generally speaking, the reason why the host alarm is three short and one long is due to the failure of the host, which may be due to hardware or software problems, which need to be checked and repaired. First of all, you should check the hardware status of the host, check whether the host's power supply, memory, hard disk, CPU and other hardware are normal, and if there is a problem, you should repair or replace it in time.

Secondly, you should check the software status of the host, check whether the host's operating system, drivers, applications, etc. are normal, and if there is a problem, you should repair or reinstall it in time. Finally, you should check the network status of the host, check whether the network connection of the host is normal, and if there is a problem, you should adjust or replace the network equipment in time. Through the above steps, the problem of three short and one long alarm of the host can be effectively solved, so as to ensure the normal operation of the host.