What are the things you need to pay attention to in the subject 2 exam?

First, candidates must gather on time with their ID cards (late arrivals will be disqualified from the test), and the staff of the driving school will bring them into the test area. (In order not to affect the test time of the next subject, candidates should hand over the tag and admission ticket to the driving school team leader for registration after the test).

Candidates are not allowed to smoke, make noise, make noise, have a bare back, wear slippers and lamps in the waiting area, and are not allowed to make phone calls (mobile phones must be kept off), and they are not allowed to keep quiet and speak loudly in the waiting area.

When the candidate (pile test) records fingerprints, the examiner randomly compiles the serial number on the spot, and after the candidate obtains the serial number, he should go to the corresponding library number for the test, and must not go to the wrong library door.

To enter the test area, please enter the test library according to the designated library number, and do not enter through the entrance of other library numbers, please wait under the library number plate.

The pile test time is 10 minutes, after the pile test is completed, the candidate must drive the car back to the starting point, cut off the infrared rays, and wait for the computer to report that the library test has passed, before opening the car door and getting off, and take the admission ticket to the second half of the waiting area (2+1). (Note: The computer did not report that the library passed the exam, indicating that the candidate did not cut off the infrared rays, and needed to continue to drive forward, and should not sit in the car and wait for a waste of time).

After the candidate obtains the lane and car number, he should go to the corresponding lane and car number for the test, and should not get on the wrong car, and should check his or her information after getting on the bus, and if the information is found to be wrong, he shall not continue the test, and shall immediately report to the examiner on duty.

On-site test items: half-slope start, side parking, right-angle turning, curve driving, speed limit through the wide door are equipped with good lights. If you pass the above items, you must drive according to the signal light and you will not be allowed to enter the project at a red light, and you can only enter the project when you have a green light.

There are 2 side garages in each lane of side parking, and you can choose any one library for the test.

If the candidate draws 3 lanes, all the test items must be completed in 3 lanes, and no one should take the wrong path. After the test, you must drive back to the start of the 3 ramps to get off.

1. Be sure to adjust the seat and rearview mirror to the appropriate position you are used to. (The left rearview mirror is adjusted to make it easy to see the left rear door handle and the left rear wheel, the right rearview mirror should be adjusted to the bottom, and the driver's seat can see that the right front handle is left and right in the middle of the right rearview mirror.) Remember to wear your seatbelt.

2. Develop a good habit of turning signals (lights are turned on no matter in and out).

3. Pay attention to the control of vehicle speed (mainly by stepping on the clutch, if necessary, you can step on the brakes appropriately, but do not step on the stop), "slow speed, fast direction" is the main point.

4. Except for the section between the test areas of each project, you can stop and wait, once you enter the test area, you cannot stop in the middle of the operation.

5. Be sure to listen to the voice prompts clearly, and let the computer judge and confirm your operation (about 3 seconds) before making the next action, and you can't be in a hurry.

6. Pay special attention to the direction not to make a mistake, "go forward to see the front of the car, backwards to see the rear of the car, and play which side you want" does not advocate the direction of the car after parking, (although no points are deducted), and advocate that the car is in the right direction after parking.

Si Youpu said that the traffic subject two exam should pay attention to the key points.

You must prepare well before the Subject 2 exam in order to pass the exam successfully, whether you go to the exam venue by car or by yourself, you need to leave in advance to prevent vignettes from affecting the progress of the exam. Be sure to dress appropriately for the exam, wear loose and comfortable clothes and shoes, and remember not to wear high heels. When you arrive at the waiting area of the examination room, you must check whether all the documents are complete, and wait for the number to be called with a relaxed attitude.

Poke me to see how ready to get on the bus.

2. Adjust the seat.

Before the subject 2 exam, students must adjust the vehicle seat, because everyone's height and weight are different, as long as the seat is adjusted to a position that suits them, in addition, the rearview mirrors on both sides of the vehicle should be adjusted in place to prevent affecting the exam.

III. Examination Process.

In the subject two assessment, "reversing into the warehouse" and "side parking" is more difficult, especially in the operation process of reversing into the warehouse, we must control the speed of the vehicle, to avoid the situation of robbing the garage and crashing, if you find that the vehicle is close to the edge line, you must slowly adjust the position of the body, in order to achieve the purpose of smooth storage. In the assessment of side parking, candidates should pay attention to the angle between the body and the reference position and avoid pressing the line.

4. Obey voice commands.

In the subject 2 exam, you must not get off the bus after completing each small item, you need to hear the voice broadcast, and you can only move on to the next item after passing, otherwise you will be judged to have failed the exam. Keep in mind that each student has two chances to take the exam, and if the first exam is necessary, you must adjust your mentality and return to the starting point, and operate carefully, the chance of passing the exam is still very high.

The above four points are the details that need to be paid attention to in the subject two assessment, in addition, candidates should also pay attention to the whole process of the vehicle can not be turned off, can not stop halfway, let alone slip, must pay attention to the distance between the vehicle and the white line can not be pressed line, all the items must be signed after the completion of the left, and finally I wish all the friends who take the driver's license can pass the test smoothly!

Be sure to pay attention to what the lights on the dashboard represent, and pay attention to the points of each item.

Subject 2: How did you get through It's too difficult.

When driving in curves, try to slow down the speed of the car, adjust the steering wheel slowly, and don't hit too much at once. When approaching a corner, you can make the body slightly to the right, let the body keep moving forward until the 2 3 line at the front of the car, and start to slowly hit the steering wheel to the left, so that the 2 3 at the front of the car keeps the line until the first corner. At the second turn, when the car mark is pressed line, the steering wheel is back to the right, and when the 2 3 of the entire front of the car is pressed, the steering wheel is slowly hit to the right, so that the 2 3 of the front of the car has been kept on the line, and the right rearview mirror can be observed to prevent the right wheel from pressing the line, and slowly drive the car out of the corner.

If you don't prompt a violation, there is no violation, and you can continue to the next exam (during the exam, the examiner monitors through the camera and infrared monitoring, and there is no problem if you don't prompt it), and the voice response is slow after pouring the library when the test is reversed.

The inverted library is exactly the same as the inverted warehouse to complete a meaning. Pay attention to the speed control during the exam and don't rush. If you have any questions, you can ask the coach in charge of the command in time.

Of course, you should choose a comfortable set of clothes and comfortable shoes for the exam. It is best to have the same thickness as when you usually practice driving, because the thickness of the clothes will affect the change of points.

When turning at a right angle, be slow and don't press the A-corner. When turning, you can look at the position relationship between the steering wheel and the corner, find a suitable position, and pay attention to controlling the speed of the steering wheel.

Reversing into the warehouse should be slower, control the speed, find the right reference point, and try to correct the body when reversing, so that it is not easy to press the line. When reversing into the garage, the steering wheel would rather hit earlier, hit earlier to return the direction to the right, reverse a little, and then kill the steering wheel. If it is late, it is generally difficult to remedy.

When entering the warehouse, look at the left rearview mirror, and return to the right direction when the body is parallel to the line. After warehousing, stop when the lower edge of the left rearview mirror coincides with the corner line of the warehouse.

Be calm and don't worry about anything. When I took the exam, I was practicing in one go.

Turn the steering wheel quickly when parking in the side position. You can see the position of corner A in the right rearview mirror, and when corner A is just about to leave the rearview mirror, hit the right full direction. Then look at the left rearview mirror, when you see the B corner behind the library, back to the right direction, and then look at the left rear wheel from the left rearview mirror, when the wheel just pressed to the virtual library line, the direction to the left to kill, into the warehouse.

When leaving the warehouse, be sure to remember to use the left turn signal.

Pay attention to the ramp fixed-point parking and starting, and when carrying out the ramp fixed-point project, pay attention to the distance between the car and the right line before going uphill to avoid pressing the line. When fixing the point, it is generally according to the appropriate point of the individual, so that the lower edge of the mirror and the upper edge of the thick yellow solid line are just fitted, and the fixed point is accurate at this time. When starting, don't forget to hit the left turn signal, step on the brakes to prevent rolling, and release the clutch slowly until the body shakes, slowly release the brakes, and the car starts.

In this process, if the ignition is turned off, directly press the brake and clutch to the end, quickly ignite, and then start according to the above steps.

Section 2 exam to stabilize the mentality, to practice the same as usual, after getting on the car will be a little nervous, take a deep breath to steady, feel less nervous at the beginning of the exam, before the exam ask the students, how many test cars are good, try the clutch soft and hard first, a car a kind of don't rush to go, this clutch that does not remember the time must be stabilized, when you are ready to start the exam, the coach tells you the point with your brain again, reverse into the warehouse must see the point, but when the library is easy to make mistakes, If there is a test car in the S bend, do not enter first, enter the S bend left small mirror root touch the line on a circle and a half called the mirror root against the line do not leave, you can adjust, look at the left reversing mirror, see the point quickly correct, into the right-angle small mirror root and the line coincide quickly play two circles, the car turned over and turned off the turn signal, out of the side turn signal does not need to be turned off, until the right angle and then closed, look at the left rearview mirror to see the body and the left yellow line, more than 20 cm less than 40 cm car right, it should be sloped, just drive according to the point taught by the coach, But don't forget to pull up and put down the handbrake.

Before the test, you need to pay attention: bring the original ID card, do not wear slippers, high heels, or colored sunglasses. Pay attention to the following when waiting for the exam:

Recall the operational elements of the test project attentively, reproduce the technical steps of the project in your brain, and ignore the discussions of others to avoid disturbing your own mind. After getting on the bus, you should pay attention: first of all, fasten your seat belt, adjust the seat and rearview mirror, and adjust the test car to the appearance you are most familiar with.

First of all, you should have a good mentality, don't be too nervous, and don't forget the methods that usually ask your coach to teach. Also, don't be too fast when you take the exam.

<>Adjust the seats and mirrors

When you start to learn to drive, especially when you are in the garage, you must remember how to adjust the seat and rearview mirror taught by the coach, and adjust it every time you get in the car. Simulations and exams should also be tuned according to this standard.

Because all points with the car as a reference will be affected by the front and back of the seat, the height, the height of the backrest, the adjustment of the rearview mirror and the height of the individual, especially the rearview mirror.

Control the clutch

This is very important, needless to say, do it slowly and non-stop, it will also be very helpful to learn to start half-slope, clutch control is not good and easy to stall.

Wait in a non-test area

Encounter other vehicles in front of you for the test. Candidates in front of you will wait in the parking area before you finish the test, and if you enter the test area and then park, you will have to park in the middle of the road.

Adjust the status

If you feel that your hands and feet are shaking or the rearview mirror is not adjusted properly during the test, you can stop in this area and pull the handbrake, adjust your breathing and start in the normal order.

Learn to see the crimping line and angle by yourself

We have to learn to judge for ourselves whether we are doing it correctly or not. If you don't know how to watch, you won't judge whether you can press the line and press the angle, and no matter how hard you practice, it will be in vain.

Exam completed

Before you hear the command "the test is over, the score is passed", do not unbuckle your seat belt, stop or get out of the car in advance; After the test, arrive at the designated place and sign to confirm the results, and then the whole subject 2 test will be completed.

Exam Sequence:Reversing into the garage Ramp fixed-point parking and starting Side-oriented parking Right-angle turning Curve driving (S-bend) may be different in different areas.

Pay attention before the exam room

Wear flat shoes and comfortable clothes for easier handling. If you are a myopic student who wears glasses when collecting information, you must also remember to wear glasses during the exam. Remember to bring your ID card, go to the test room in advance, and pay attention to whether your name is called at any time.

I wish you all the best in the second exam!

1.Adjust the seats and mirrors

Because all points with the car as a reference will be affected by the front and back of the seat, the height and the angle of the backrestMirror adjustments and personal height, especially mirrorsTherefore, it is especially important to adjust the seat and mirrors. Unless you're too skilled, it's good to tune it up and learn to be flexible.

2.Control the clutch

Do it slowly and non-stop, and when changing gears, the clutch must be stepped on to the end. Loosening the clutch must be slow. It will also be very helpful to learn to start halfway upClutch control is not good, and it is easy to stall.

3.Find the right way to practice effectively.

The method is not right, and the effort is in vainSuffer in vain. You can find a way to see something that suits you online, orAsk your friends who are learning to drive together.

4.Learn to see the crimping line and angle by yourself

When you practice, it's not that the coach keeps staring at you, or that you always have a friend who accompanies you to watch for you. If we don't predict whether we will press the line and press the angle, no matter how hard we practice, it will be in vain. Beginners can stop and get out of the car to confirm whether the line is pressed and the angle is pressed

5.Adjust your mentality, and guard against arrogance and rashness for both those who learn well and those who are not

Avoid:Unfastening your seat belt before the test is over or forgetting to fasten your seat belt before starting the test; Forget to turn signals when parking on the side and turning at right angles; Failure to follow the rules of the test room and step on the accelerator; Pass the exam and get carried away with your hands behind the wheel; The vehicle is turned off and the gear is ignited; I was too excited to get to the last project, and I made a mistake in operation.

6.Pay attention to the peers who practice and test together

Don't practice with a negative and irritable partner, having a reliable practice partner will be very helpful for you.

7.Complete one item during the exam and think about the next one and the precautions

8.Keep it in your hands

It is best to practice twice a day a week before the exam to avoid being born or careless due to long-term non-training.

9.Keep up your energy

The waiting time for the second exam is relatively long, and I often leave before dawn to wait for the exam for more than half a day, prepare dry food, and pay attention to cold and heat prevention. If the person who doesn't wait is hungry and sleepy, distracted, and inattentive, it will definitely affect the exam.

10.Luck + character.

Although it is more reasonable to make an appointment for the exam after practicing well, people who practice badly may also be lucky enough to pass the exam. I hope you all go well!