What should I do if the rear tail light gets into the water?

Generally, it is necessary to replace the tail lights with new ones. If the lamp gets into the water, if you don't change it, remove the tail lamp, then dry it with an electric wind, and use glass glue to the lamp seam.

Transparent) can be sealed, you can also drill one or two small holes at the bottom of the lamp, after a period of time there will be no water vapor, even if the water leaks will be discharged in the small holes, this method is very simple, and very useful, the master is repairing the car.

This trick is often used when it comes to light fixtures when water enters the water and it is usually difficult to find the leakage area, which is a rule of thumb.

There are two kinds of water ingress in car headlights, one is slight water ingress and the other is severe water ingress. 1. Slight water inlet treatment method is relatively slight water ingress in the lamp, the driver does not have to worry too much, after the lights are turned on for a period of time, the fog will be discharged out of the lamp with the hot air through the ventilator, which will basically not damage the headlights and electrical circuits. 2. Heavy water inlet treatment method: The water inside the headlamp is enough to raise fish.

Disassemble it, open the lampshade, dry it, check whether there is any damage or possible leakage on the surface of the headlight, if you find abnormalities, it is recommended to replace the sealing strip and snorkel of the headlight back cover. Precautions for water ingress of headlightsAfter the headlights enter the water, the headlights must not be baked, which is easy to damage the headlights, because the appearance of the headlights is made of plastic, and the extra heat is easy to bake the lampshade, and most of this damage is irreparable. As far as the overall structure of the headlights is concerned, whether it is ordinary halogen headlights, xenon headlights or headlights with LED light clusters, they will be equipped with a ventilation tube, and the function of the ventilation tube is to exhaust the heat as much as possible out of the headlights, so as to maintain the normal working temperature of the headlights and ensure the stability of the headlights.

If the car wades in water, the external moisture will enter the inside of the headlight through the snorkel and attach to the lamp cover, thus affecting the brightness of the headlight, and even damaging the lamp circuit.

The simple way is to drill a small hole under the rear taillight cover of the car, and then make a hole at the top, so that the air is convection, and the water entering the taillight will come out by itself.

My car has water at the rear taillights, and when I open the trunk and press it down, just when I close it, there will be water coming out of the taillight hole. But he didn't go inside. I asked the master of the 4S shop and said that it was okay, the inside was closed, and there would be no water.

If there is water in each tank, it will be wiped clean or 800 tons will be unloaded to evaporate the water inside.

I'm afraid that I'm not doing something very well, and I'm worried that I'm annoying people. This kind of concept is actually because of a kind of caution about the unknown, because it is not clear what kind of person is opposite.

Water treatment method for automobile tail lamp. If there is only a slight inflow of water, it is relatively slight under the lamp. Don't worry too much.

If there is heavy water ingress, remove it first, open the lampshade, and dry the ,..Inspect the surface of the tail light for possible damage or water leakage. If you find this phenomenon, please go to the 4S store as soon as possible for disassembly and maintenance.

It is recommended to replace the headlight cover seal.

and ventilation pipes. <>

from the headlights of the car.

The overall structure of the lamp, whether it is a traditional halogen lamp.

Or xenon lamps.

Or LED headlights Naki, basically equipped with a ventilation hose, the purpose of which is for the radiation of the light, because the illumination of the light will cause a lot of heat, if it is stuffy, the air in the light will be quickly heated and expanded, and may even affect the bursting situation.

It is because of this tube that the moisture in the air enters the headlamp through it and adheres to the lampshade, along with the water vapor.

, the moisture in the lamp is correspondingly more. I guess this situation is mainly due to the excessive temperature difference, especially in the winter or rainy season. But in most cases like this, friends don't have to worry too much, because after the headlights are turned on for a period of time, the water may also be discharged through the ventilation duct with the heat of the headlights, and in general, it will not affect the headlights and circuits.

And at present, most of the headlights are basically integral, and the transparent lampshade is also attached to the back plate to protect the lamp body, and high-temperature baking may also cause the glue between the two to melt, which will increase the risk of water ingress into the taillights. , but I believe that the gap between the tram is not big, and it is possible that we can be the boss when overtaking in corners.

Do a detailed interpretation of the problem, I hope it will help you, if you have any questions, you can leave me a message in the comment area, you can comment with me more, if there is something wrong, you can also interact with me more, if you like the author, you can also follow me, your like is the biggest help to me, thank you.

If you find that the rear tail light of the car is flooded, you can choose to remove the lampshade, drain the water and dry it, if the headlight is damaged, you can repair it; You can remove the lampshade to dry, and then check whether the surface of your rear tail lamp is damaged or the circuit is flooded, if this happens, you need to replace the circuit in time.

After removing the tail lights of the car, the water will be sucked clean, and then the tail lights will be dried with professional tools to avoid short circuits. When repairing, you must use professional tools, disassemble the shell, and use a dry rag or a cloth with strong absorbency to absorb the water and sell it.

If the rear tail light of the car is flooded, you should go to the car repair shop for repair; The rear tail lights of the car should be disassembled, and then the water inside should be cleaned out, then ventilated and dried, and finally the lights are installed, but I think it is best to go to the repair shop for Wei Ruxian repair, so that it is safer and more secure.

What should I do if the rear taillights of my car get water? Need to go to a 4S store? Water accumulation in car tail lights will affect light transmittance, especially at night, which will greatly reduce the line of sight, change the direction of illumination of lights, affect other vehicles and pedestrians, and seriously interfere with the driver's normal line of sight, if the water accumulation is serious, the bulb and circuit will also be damaged, there are two situations of water ingress in car taillights, one is slight water ingress, and the other is serious water ingress, and these two situations are handled differently.

Slight water ingress The internal light is relatively weak Water ingress In this case, the driver does not have to worry too much, after the light is turned on for a period of time, the fog will be discharged through the ventilation pipe along with the hot gas outside the lamp, and the ventilation pipe tail light and circuit will not be damaged, and the water in the severe water inlet car light is enough to raise fish. If this phenomenon is found, you should go to the 4S shop as soon as possible to disassemble and repair it, or disassemble it, open the lampshade to dry, and check the surface of the headlamp for damage or possible leakage. If any abnormalities are found, it is recommended to replace the sealing strip and ventilation duct of the back cover of the headlamp.

Do not bake the headlamp after the automatic lighting has entered the water, because the appearance of the headlamp is made of plastic, and the extra heat can easily bake the lampshade, and most of this damage is irreparable, so it is easy to damage the headlamp. There are usually these three reasons for the car to get into the water. First of all, the lamp had been reinstalled before, and the removed headlamp was not reinstalled tightly, and the gasket was leaking.

Second, the collision of the lamp components causes cracks or deformation of the headlights, affecting the sealing of the headlamps and causing cracks. Third, non-human factors, such as poor lamp technology or aging gaskets.

If water enters the car taillights, there will be residual water inside the headlights because the water refracts the light and the direction of the headlamp illumination light may change. At the same time, the transmittance of the headlamp itself is also affected by the influence of fine water mist. This change may affect other driving behaviors, car interference and increase the probability of car accidents, the owner should go to the 4S shop for maintenance as soon as possible, because the plan of the previous stage of water ingress is not right, the internal structure of the tail light circuit may be affected, but if it is not repaired for a long time, the internal water may damage the circuit.

After the rear tail light gets into the water, you can go to a repair shop to clean it up, and there is no need to go to the 4S shop. Because if you go to a 4S shop for repair, ** is very expensive, you only need to find a repair shop.

If it is a slight water ingress, turn on the tail lights for a period of time, the water will evaporate, and if the water ingress is more serious, you need to go to the 4S shop for maintenance; Need to go to the 4S store.

The rear taillights of the car got into the water, as long as it was in the sun for a few days, so there was no need to go to the 4s store.

Automobile tail lamp water inlet treatment method:

1. If it is only a slight water ingress, it is relatively slight in the light, don't worry too much, the lights will light up for a period of time, and the fog will come out of the lights with the hot air through the ventilator, which will not damage the tail lights and circuits;

2. If it is a case of heavy water ingress, remove it first, open the lampshade, and after drying, check whether there is any possibility of damage or leakage on the surface of the tail lamp;

3. If this phenomenon is found, it should be dismantled and repaired in the 4S store as soon as possible, and it is recommended to seal the headlight cover and ventilation pipe after replacement.

My balance is boring because there is water at the rear taillights, and after opening the trunk and then pressing down, it is just about to turn it off, and there will be water flowing out of the taillight holes. But he didn't go inside. I asked the master of the 4S shop and said that it was okay, and the inside was sealed and closed, and it would not enter the water.

Spring is coming, and so is the rainy season. Water ingress into car taillights is a common occurrence. If not treated immediately, it will affect the light transmittance.

So what should I do if the taillights of my car get into the water? There are two types of water ingress in car taillights, one is slight water ingress and the other is severe water ingress. These two situations are handled in different ways.

1.Drivers, don't worry too much, the lights are slightly watered. The lights are on.

Spring is coming, and so is the rainy season. Water ingress into car taillights is a common occurrence. If not treated immediately, it will affect the light transmittance. So what should I do if the taillights of my car get into the water?

There are two types of water ingress in car taillights, one is slight water ingress and the other is severe water ingress. These two situations are handled in different ways.

1.Drivers, don't worry too much, the lights are slightly watered. After the light is on for a period of time, the fog will be discharged through the vent pipe with the hot air, and the tail light and circuit will not be damaged.

2.The water inside the heavy-duty air intake headlights is enough to keep fish. If you find this phenomenon, you should go to the 4S shop as soon as possible for disassembly and repair, or disassemble and open the lampshade.

Once dry, inspect the surface of the headlamp for any damage or possible leaks. If there is an abnormality, it is recommended to replace the sealing strip and snorkel of the back cover of the headlight.

Things to look out for:

Never bake a headlight after water has entered it. Doing so can easily damage the headlights, because the headlights are all plastic, and the excess heat can easily burn the lampshade, and most of this damage is irreparable.

As the saying goes, "Do it yourself, have plenty of food and clothing." "When water gets into the taillights, we have to deal with it manually. Saving money by asking for help from someone special is also a lot of money. Raid, I hope the content compiled by Bian Xiao can be helpful to you.

What to do if the car taillights get into the water.

At present, the rainy season is approaching, and there are frequent incidents of water ingress into car taillights. If not treated in time, the water accumulation in the headlights will affect the light transmittance, especially at night, the line of sight will be greatly reduced, and it will also change the lighting direction of the headlights, affecting other vehicles and pedestrians, and seriously interfering with the driver's normal line of sight. If the water accumulation is severe, the bulb and electrical circuit will be damaged.

Next, I'll teach you what to do if the car taillights get into the water.

There are two types of water ingress in car taillights, one is slight water ingress and the other is severe water ingress. These two situations are handled in different ways.

1.Drivers, don't worry too much, the lights are slightly watered. After the light is on for a period of time, the fog will be discharged through the vent pipe with the hot air, and the tail light and circuit will not be damaged.

2.The water inside the heavy-duty air intake headlights is enough to keep fish. If you find this phenomenon, you should go to the 4S shop as soon as possible to disassemble and repair it, or disassemble it and open the lampshade.

After drying, inspect the surface of the headlamp for any damage or possible leaks. If there is an abnormality, it is recommended to replace the sealing strip and snorkel of the back cover of the headlight.

Reminder: Never bake the headlights after water has entered the headlights. Doing so can easily damage the headlights, because the headlights are all plastic, and the excess heat can easily burn the lampshade, and most of this damage is irreparable.

What to do if the car taillights get into the water @2019