THE START IP AND END IP OF THE TENDA ROUTE

m only means that it can reach a maximum of 600kb seconds, but it generally does not exceed this speed. Therefore, the ** internet speed limit for each computer is 200k. Because the broadband is usually ADSL, that is, asymmetrical broadband, the upload speed is generally not limited.

Each computer corresponds to an intranet IP address and MAC hardware address, which will not be changed when the router DHCP is automatically assigned, but it is not excluded that the intranet IP address of 3 computers will be changed due to accidents. Therefore, one of the preparations is to go to the DHCP service settings and bind the MAC address of each computer to the fixed private IP address currently in use. In this way, the intranet IP address of each computer is fixed, which is convenient for further QoS settings.

3. Enter the bandwidth control to set QoS, create rules for the three computers respectively, the IP range can be set to the last bit 2-2, if it can't be repeated, you can go back to the DHCP binding private network address just now, and divide the IP addresses of the three computers into three segments, for example, the last bit is 8, a 12, a 16, and then go back to the QoS settings, the first assignment IP address range is 2-9 (in fact, only the bandwidth rule with the last bit is 8, and because 1 is the router), and then create the second one, The same is true for the third clause of assigning an IP address range of 10-13 (in fact, only the bandwidth rule with the last bit of 12 is restricted, and because 1 is a router).

4. As for the bandwidth setting, it goes without saying that it is good to set the value.

5. Finally, don't forget to change the username and password of the router's management account to prevent others from entering and tampering with it.

Hope the above helps.

I can tell you, that probably doesn't really mean much!

That's what it means.

Let you enter. You have to control the traffic of those i machine IP addresses.

That is, the IP that includes these IP addresses.

If the IP address does not change.

Then both the start and end are entered into the IP address of the machine to be controlled.

Judging by your narrative.

You may be using the DHCP feature.

It is recommended to turn off DHCP

Use a static IP address.

If you use dynamics, it's not easy to control.

Unless your router supports multiple network segments.

It is the starting IP of the routing IP he provides, which is generally default, or enter a value at random, between 1-255, just fine.

The format of the IP address is generally from the beginning to the end) of the household

The last number can be set arbitrarily, but there cannot be the same value in a network.

The DHCP service can assign an IP address range to the computers connected to the router, that is, how many computers can be assigned IP addresses, which can be flexibly set according to your needs!

Whatever you want, like between.

The first three bytes of the IP address in QoS are the same as the LAN interface, which cannot be modified, for example, the LAN interface is, and you want to limit it, then set it on the page"20"-"25", in quotation marks you can fill in.

Look at the ** written on the back** and quickly set the username admin password after entering.

Then enter your account and password to continue the settings, and then restart the router and it's OK

The rate-limiting IP cannot be filled in because this IP is the address assignment of the router, and the rate-limiting range starts into.

The second tassel should not be within the range of 2 100 in the first article) x (as long as it does not exceed 254).

Just leave it empty, don't fill in this if you have your own home.

The second time: Enable bandwidth throttling to tick off. Remove this.

1. Open the IE browser that comes with the system;

2. Enter the IP address of the router: most of them are on the label on the router);

3. Enter the administrator password (if you haven't changed the password of the router, use the admin password), and then confirm;

4. Select the DHCP server, and then click on the client list.

5. This is the list of all devices connected to this router;

6. The device names (in English) and MAC addresses and IP addresses of all users connected to the router are displayed here.

There is usually a client setup in the router.。。 There should be a display inside... Or there is a connected client in the running state at the front of the interface, which shows how many are connected.

The router automatically obtains the IP address, which needs to be set in the background of the router.

1. Enter the router address in the browser address bar.

2. Enter the administrator password to enter the router background management page.

3. Click Advanced Settings on the router background management page.

4. Select Setup Wizard.

5. In the setup wizard, select Automatically get IP address.

If you enable DHCP, you can automatically assign an IP address.

Use the IP address (prompted on the back of the router) and enter the address bar of your browser, then enter the username and password.

DHCP Server DHCP Service is enabled.

The address at the beginning of the address pool and the address at the end of the address pool can be adjusted and saved to take effect.

Address rental period is 120 minutes by default (if the network is disconnected for 2 hours, you can set a longer time) Save.

The fourth item, the DHCP server, put that on.

In the local connection, the IP address must be automatically obtained.

If a machine cannot obtain an IP address, you can disable DHCP, then each machine can manually specify the IP address.

Do you see that DHCP service, turn that service on, and then set the address pool.

If you change the router again, it may be broken.

3. Tengda portable wireless router and 3G wireless router are used as settings**.

4. There are also a small number of models of wireless routers that are used as a set**.

Can I study right away if I sign up now?