Please that master has a detailed explanation of the WAS test report, please give me a copy of 10

5 points, so much to explain, don't die,

There are too many junk files, just use Windows Optimizer to sweep aside the junk files.

Right-click on c:, Properties -> empty, OK

Luckily, we can solve the new learning problem mentioned in my last email. Obviously, it was all the communication failures that were generated on the computer, we replaced the CPU and learned to run the last software you sent using it. I send you a new report of all the NG learning channels.

Most of the failures were done by BMS engineers, and they were here at the time. They also diagnosed the problem and made a list of all the needed spare parts. Actually, we have 83 ng channels for a total of 800 channels.

32 of those NG channels, we can't test them correctly. We'll connect it clearly and I'll verify your symptoms). Due to the time BMS engineer is here, the new channel starts to fail.

The new NG channel is shown in yellow.

Luckily, we can solve the new me last email mentioned in the study problem. Obviously this is the failure of all the communication generated by the computer, we replace the CPU and learn to run it using the last software to send you. I send you a new report for all NG learning channels.

Most of the failures are believed to have been done by BMS engineers at their place. They also diagnosed the problem and made a list of all the spare parts needed. In fact we have 83 ng channels from 800 total channels.

32 ng channels from those we can't test them properly. We will connect it clearly soon and I will confirm your symptoms). Since the BMS engineer is here, the new channel starts failing.

The new NG channel is a multicolored yellow.

Fortunately, we can solve the new one.

The study problem mentioned in my last email. Obviously it was all the communication failures that the computer generated, we replaced the CPU and.

Learn to use the software of the past to run what you sent.

I'm sending you a new report on all NG learning channels. Most failures are caused by system engineers when they are here. They also list the diagnosis of the problem and all the spare parts needed.

In fact, we have 800 ng channels from 83 channels. (32 ng channels from those we can't test correctly.) We will be sure that soon I will verify your symptoms).

Due to the time BMS engineer is here, the new channel starts to fail. The new natural channel is yellow.

It may be that the naming method is different, generally as long as the configuration is okay and the model is fine, it will be fine.

It is recommended to add 2G memory, because Win7 uses 2G memory, and XP uses 512MB, which is very tense.

You disconnect the network cable and try to turn it on, if there is no problem, it is caused by slow boot networking, and it has nothing to do with the system. If it is still like that, use the software to optimize the power on and off speed, it still doesn't work, it is recommended to restore the system or reinstall. If it doesn't work, format the hard drive and repartition it to reinstall it (if it's a network problem, try setting a fixed IP).

If it is not caused by slow networking, first soft and then hard, if such a problem occurs, such a problem is caused by software conflicts, inappropriate drivers, and system problems, you can restore the system in safe mode, or not reinstall the operating system, do not install software, patches, drivers, etc., and see if there is still a problem with booting? If you don't install drivers, patches, and software step by step, don't install them if you find something that isn't suitable (if it's a hardware problem, please overhaul it, such as hard disk, etc.).

It would be nice to optimize the startup speed with 360.

You have a few gigabytes of RAM on your computer.

To put it simply, there are a total of four events from the picture you sent:

1.Connector loss, distance from the monitoring point, joint loss, total attenuation at 2Connector loss, distance from monitoring point, joint loss, total attenuation at 3Connector loss, distance from monitoring point, joint loss, total attenuation at 4Splice loss, distance from monitoring point, splice loss.

Probably this is the case, in this chart, the attenuation curve is not normal, several events are too attenuated, or there is a problem with the test parameters. The specific situation still has to be seen on the spot, and I am based on you.

The diagram given is roughly analyzed. Hope it helps!

Leave an email address and communicate more

You failed this test.

It is recommended to use the manual test method to change the pulse width to a smaller point and the test distance to a smaller point before testing.

I'm dizzy, it's too short. A lot of things don't show up, so I recommend using manual testing.