How Do I Configure Port Aggregation on a Switch?

<><3. Set the port mode to trunk.

4. Add link group 1 and enable it.

5. Distribute data according to the IP address of the target host to achieve load balancing, and click "Copy".

6. Configure switch 1 according to switch 0.

<><3. Set the port mode to trunk.

4. Add link group 1 and enable it.

5. Distribute data according to the IP address of the target host to achieve load balancing, and click "Copy".

6. Configure switch 1 according to switch 0.

The aggregation layer switch is the aggregation point of multiple access layer switches, which can handle all the traffic from the access layer devices and improve the uplink leased to the core layer. <

1. The aggregation layer switch is the convergence point of multiple access layer switches, which can handle all the traffic from the access layer equipment and provide the uplink to the core layer, so the aggregation layer switch requires higher performance, fewer interface silvers and higher switching rate than the access layer switch.

2. Access switches are generally used to directly connect to computers, and aggregation switches are generally used between buildings. Aggregation is equivalent to a local or important transit station, and the purpose of the access layer is to allow end users to connect to the network, so the access layer switch has the characteristics of low cost and high port density.

Summary. Gigabit Ethernet cables are usually used for network cables between access switches and aggregation switches. Gigabit Ethernet cable is the most common network cable of traditional Ethernet, also known as Cat5e Cat6 network cable, which can support 10 100 1000Mbps transmission rate.

Among them, the CAT6 network cable has stronger anti-interference, which can theoretically support higher transmission rates, and is usually used for long-distance transmission to transmit data at a higher speed. I hope I can help the little master <>

The network cable between the access switch and the aggregation switch usually uses a Gigabit Ethernet cable. Gigabit Ethernet cable is the most common network cable of traditional Ethernet, also known as Cat5E Cat6 network cable, which can support 10 100 1000Mbps transmission rate. Among them, the CAT6 network cable has stronger anti-interference, which can theoretically support higher transmission rates, and is usually used for long-distance transmission and transmits data at a higher speed.

I hope I can help the little master <>

I ran out, I used the network cable cat5e to connect the access switch to the aggregation switch, it is a fuel brigade, not the access switch, will not use the optical module, only the aggregation switch spring section through the fiber optic jumper will use the Pilsen stool optical module.

Yes, there is no need to use a photo-molded pin pin when using a CAT5E network cable to connect to an access switch. Optical Douxiang modules are typically used to connect long-distance fiber optic connections between aggregation switches and other devices. If you want to connect the aggregation switch and other devices through fiber patch cords, you need to use an optical transceiver.

In my picture, an aggregation switch comes out with two fiber patch cords, and a couple of optical modules are used.

In general, two optical modules are used. One fiber patch cord will be connected to one module, and another fiber patch cord will be connected to Sega to another module. The two modules are then connected to the two LU ports of the aggregation switch. <>

This photoelectric receiver comes out of the fiber optic patch cord.

Is it also to use an optical module?

Generally speaking, the optical module of the optical fiber in the photoelectric receiver can be an independent module, or it can be integrated with the outgoing optical fiber destroyer Zheng jumper. The specific situation needs to be determined according to the design of different products. It's not easy to judge <> situation at the moment

The aggregation layer is the aggregation point of multiple access layer switches, which must be able to handle all the traffic from the access layer devices and provide uplinks to the core layer, so the aggregation layer switch requires higher performance, fewer interfaces and higher switching rate than the access layer switch. The function of this layer is mainly to implement some of the following strategies:

1. Routing (i.e., the best path for files to be transmitted in the network);

2. Access table, packet filtering and sorting, network security such as firewall, etc.

3. Redistribute routing protocols, including static routes;

4. Routing between VLANs and other functions supported by working groups;

5. Define the multicast domain and the broadcast domain. This layer is mainly where the strategy is implemented.

Aggregation layer 1000BASE-T switches are available in both chassis and fixed-port designs, which can provide multiple 1000BASE-T ports, and can generally provide other types of ports such as 1000BASE-X. Together, the access layer and aggregation layer switches form a complete small and medium-sized LAN solution.

The basic functions of the aggregation layer are as follows:

1. Converge the user traffic of the access layer to carry out the aggregation, exchange and exchange of data packet transmission;

2. According to the user traffic of the access layer, local routing, filtering, traffic balancing, QoS priority management, security mechanism, IP address translation, traffic shaping, multicast management and other processing;

3. According to the processing results, the user traffic will be routed to the core switching layer or locally;

4. Complete the conversion of various protocols (such as the aggregation and re-release of routes, etc.) to ensure that the core layer connects the regions running different protocols.

Hello, port aggregation is port aggregation.

There are the following requirements:

The physical parameters at both ends of the aggregation link must be consistent.

The number of links that are aggregated.

The rate at which the link is aggregated.

Duplex mode of the link where aggregation takes place.

The logical parameters at both ends of the aggregation link must be consistent.

The basic configurations of ports in the same aggregation group must be the same, including STP, QoS, VLAN, and ports.

Hope it helps!