How to use the new water heater and how to use the water heater?

It depends on what kind of water heater it is. There are mainly instantaneous gas water heaters and storage electric water heaters, which are the two most common.

Instantaneous gas water heater: After turning on the natural gas, plug in the power socket, open the gas valve, turn on the machine, adjust the hot water temperature, turn on the hot water faucet, and the water heater will be ignited and operated.

Storage electric water heater: Turn on the cold water faucet to fill the water, turn on the power supply, set the water temperature, and after a period of heat, it can be used normally.

Medis wall-hung boiler, dedicated to your service.

1. Plug in the power supply, press the switch button of the electric water heater, and set the water temperature at the same time. Normally, I set it at 45 degrees, but in winter, the temperature can be turned up a little higher.

2. After the water boils, first adjust the valve to the middle position, put the water, and try that the water temperature is not cool before starting to use. (Generally, the left side of the valve marked with the word H is hot water, and the right side marked with C is cold water.) Hot water is marked in red, and cold water is shown in blue. )

3. After the water temperature is constant, it can be used, because the electric water heater is surrounded by water, which is easy to be electrocuted, so try not to touch other places with your hands or other parts during use, especially around the power supply.

4. When using the electric water heater, when the water valve is opened and there is no water, the power supply should be disconnected immediately to prevent the electric water heater from being damaged due to failure when working without flowing water.

5. If the water pressure or voltage is too low, the use should be suspended.

6. After use, turn off the switch on the electric water heater first, wait for your hands to dry, and then unplug the power.

Just look at the manual before using the new Midea energy-saving water heater.

You can see the description above.

The correct way to use the water heater is as follows:The first step is to turn on the water heater outlet switch (shower), as shown in the figure below.

The second step is to turn on the water inlet pipe switch, and the water will automatically be pressed into the inner tank, as shown in the figure below.

Step 3: Plug in the plug, the electric water heater will automatically heat up, and the indicator light will turn on until it is heated until the light changes color, as shown in the figure below.

Step 4: Adjust the summer or winter button on the water heater, as shown in the figure below.

Fifth, there is also a button to adjust the temperature on the water heater, rotate it to the coarser part of the icon, indicating that the temperature is larger, and vice versa, the temperature will be smaller, as shown in the figure below.

Turn on the mixing control valve on the water heater, check if there is water spraying out of the sprinkler, and check if there is enough water in the tank.

2.Plug the water heater into the socket and press the switch of the power supply on the control panel.

3.When the screen is on, enter the settings state and use the plus and minus keys on the left side of the screen to adjust the temperature.

4.After the above steps are completed, when the time is up, the water heater will enter the automatic heat preservation state, and the sprinkler head can be turned on for use.

Ask this kind of question.

In general, if this is set, you don't need to set it up again.

If you want to set this up, you need to turn on the faucet first.

This should be adjusted only after the water is inducted.

Hello! Your first ** is used with the light of the bath bomb and the heater, and the water heater is the second **, you have to adjust its temperature point to increase the temperature.

Plug-in water heaters need to be powered on.

Solar energy needs to be exposed to the sun.

Hybrid water heater both.

To open the inlet and mixing valves, the electric water heater must have enough water. Be careful not to turn the water in the direction of the human body when you first open the valve. The electric water heater should be set up before use, that is, the amount of water, according to the number of people taking a bath to choose a good mode, when the time comes, the electric water heater will supply a few people to wash the amount of water, generally as fast as possible.

In addition to the amount of water, that is the temperature setting when the electric water heater is used, as long as the desired water temperature is set before taking a bath, the temperature of the bath will be that water temperature at that time. Before heating the electric water heater, make sure that the mixing valve is closed, that is, you need to press the handle. This prevents the sprinkler from spilling on the body or wasting it after opening the inlet valve.

Precautions for the use of water heaters.

In general, moving to the left is to produce cold water, and moving to the right is to produce hot water.

According to the electronic display screen of the electric water heater, the water temperature in the water heater can be grasped in real time, and the bath can be carried out after the set temperature is reached.

When using an electric water heater, if the water outlet switch is turned on but the water does not come out, the power supply needs to be cut off immediately to avoid damage to the electric water heater due to failure and no flowing water.

It is possible that the working parameters of the water heater are incorrect, and the water heater itself has abnormal faults.

It is recommended to ensure that the power supply of the water heater is normal, carefully check the setting parameters of the water heater according to the product instruction manual given by the manufacturer, ensure that the setting parameters are correct, and cancel the possible timed heating function.

After that, the water heater still can't heat the water normally, that is, the water heater has an abnormal fault and needs to be repaired to the product manufacturer.

If you buy a water heater, it is better to buy a little better, and it is durable and you don't have to worry about it.

It could be that your water heater temperature sensor is broken, or it could be that your water heater heating rod is broken.

1.Open the hot water valve or hot water faucet of the cold water control valve first so that the air can be exhausted when the water is filled.

2.Then open the tap water valve leading to the water heater and fill the water heater with water. Don't drive it too big and have a big impact.

3.When there is water flowing out of the hot water faucet or nozzle, it means that the water heater is full of water, and close the hot water outlet valve. For the first time, the water heater must be filled with water before heating, otherwise it will be damaged by dry boiling.

The precautions for water heaters are:

1.When opening the mixing valve in the bath, the nozzle should not be directly aimed at the human body, and should be used when the water temperature is adjusted to an appropriate level, so as not to cause discomfort to the user if the water temperature is too high or too low. When taking a bath, make sure that the sprayed water does not pour on the water heater to avoid a wet short circuit in the internal circuit of the water heater, which may cause danger.

2.After you take a shower, first keep the sprinkler head away from your body, then turn off the mixing valve, turn off the water heater, and drain the water in the sprinkler. And hang the nozzle on the nozzle holder.

3.If the user does not use the water heater for a long time, the water in the inner tank of the water heater should be drained to prevent the water from deteriorating, causing the smell and scaling of the inner tank. Drainage method:

Close the tap water inlet valve first, then turn the mixing valve of the water heater to the hot water position, and then turn the handle of the safety valve up to the horizontal position. At this time, the water in the inner tank of the water heater flows out through the pressure relief port of the safety valve and flows into the sewer through the drain pipe.

4.Before the water heater is powered on, it is essential to make sure that the water heater liner is filled with water. Otherwise, the water heater will be boiled in vain, the heating pipe will be damaged, and the thermostat will trip.

Water filling method: Turn the mixing valve to the hot water position, and then open the tap water inlet valve. When the nozzle continuously discharges water, it means that the water in the water heater is full, and then it can be heated by electricity.

The steps for the proper use of the water heater are as follows:

Materials: electric water heaters, faucets, sockets, etc.

1. Align the power plug of the electric water heater that can be used normally with the socket.

2. Unscrew the two valves under the electric water heater at the same time, one is the valve that flows out of hot water, and the other is the valve that injects cold water.

3. Find the thermostat on the electric water heater, set the temperature according to your own needs, and when the water temperature is set, the thermostat will be automatically turned on.

4. Adjust the temperature of use, when using hot water, you can adjust the temperature of the water by rotating the faucet. Generally speaking, rotating in the red (or H) direction is hot water, and rotating in the blue (C) direction is cold water.

5. If you don't use it often, you can choose a quick-heating electric water heater, which only takes 15 minutes to heat up, with fast heating speed and short waiting time.

Operation Balance Method:

1. Install the water heater: First of all, after we buy the gas water heater, the master of the manufacturer will come to help us install it, such as: fix the position of the water heater, connect the power supply and smoke exhaust pipe, and connect the gas tank and so on

2. After installation, the master will teach us how to use it. It doesn't matter if you don't teach, let's learn with us now. First of all, let's learn about the water heater, the water heater.

3. First of all, let's get to know the interface of the water heater, there is a power switch, and there is a temperature adjustment button up and down keys

4. At this time, we first connect the water heater to the power supply, then press the power on and off to turn on the power, and set up and down to adjust the temperature of the water heater.

5. After setting it up, then open the hot and cold water valve first, then open the gas valve, and the gas valve on the water heater

6. After opening, the water heater will start to work automatically at this time, and it will generally be heated quickly. If you don't use it for a long time, you can turn off the gas valve, water heater power and hot and cold water valve.

7. The working principle of the gas water heater: when the cold water enters the water heater, a certain pressure difference is formed under the action of flowing water, in this case, the power supply will be pushed, the ignition will be turned on, and the water heater will enter the normal working state after ignition, but this state will last for a short time, at this time, there will be water shortage, high temperature, lack of gas and other faults, when these failures occur, the power supply will be automatically cut off, and the gas valve will be cut off. Therefore, a gas water heater of acceptable quality is safe and can be used with confidence.

The first finger of the slow dissipation needs to be plugged in first, turn on the switch, select the appropriate temperature for heating or preheating, turn off the switch after use, and unplug the power supply. The specific steps are as follows:

1. The water heater generally moves to the left to cool water, and to the right to move hot water.

2. The electric heater is equipped with a faucet, and with a return device, usually blue which state means cool water, red means hot water, now turn on the water switch, start to water it, then plug in the power supply, press the switch button of the electric water heater.

3. Choose the right temperature for heating, you can also make an appointment for heating according to the demand, and when the temperature of the water heater is heated to the specified temperature, it will be in a state of insulation.

4. After the water heating is completed, adjust the valve to the middle position first, and use it after the water temperature is constant. The outlet water temperature can be adjusted to the left or right according to the temperature of the room temperature. Turn off the switch after use, and unplug the power supply.

Notes:

When showering, you should choose a suitable temperature that you can accept, and the temperature of the water should not be too high or too low to avoid getting sick and cold.

1. When the electric water heater is just bought, it generally cannot be used immediately, so it should be installed in a suitable position in the bathroom first, and then debugged to see if the electric water heater is abnormal in the process of operation, and make sure that the electric water heater can operate normally before it can be used by the family.

2. In order to avoid electric shock, the socket of the electric water heater should also have a reliable ground wire, and a leakage protection device should be installed in the power supply wide nuclear damage system. Because the power of the electric water heater is large, the electric water heater must use 4 flat wires and three-pin sockets.

3. When using an electric water heater, you should also pay attention to the type of electric water heater, if the electric water heater is a storage type electric water heater, you need to fill the electric water heater with water, and then start heating, after the heating is over, you can use the electric water heater.

4. If the electric water heater is an instantaneous electric water heater, you don't need to fill the electric water heater with water, just turn on the switch of the electric water heater directly, and then unscrew the water dragon vertical head, and the hot water can be released. Instantaneous electric water heaters generally have to wait about five seconds for heating up, and the temperature of the water released is generally in a moderate state.

5. In order to ensure the safety of yourself and your family, it is recommended that you regularly use a voltage tester and other tools to check the leakage protection device at home.

The gas water heater sets the temperature of the water you need. Help me turn on the faucet from the left. Wait for half a minute for the hot water to come out.