Lenovo LJ2200 printer how to change toner

The printer can be inked by following these steps:

1. Put paper towels or other hygroscopic materials on the countertop to absorb the spilled ink.

2. Gently remove the label paper on the ink cartridge to expose the ink injection hole.

3. Place the cartridge on the spread out paper towel (nozzle down).

4. The five small holes arranged under the label are the air guide holes and the ink injection holes, and the holes are pointed against the light (or inserted with a toothpick) to correctly distinguish the position of the three colors that will be injected (black is generally added to the hole in the middle). Take out the spring bottle filled with various colors of ink, remove the sealing cap, carefully discharge the air in the spring bottle, insert the needle from the ink injection hole to the end, and then pull out 2-3mm, slowly squeeze the ink bottle with your fingers, slowly pull the needle out while investing, and the black ink cartridge is expected to add 3-5ml;

5. Place the ink cartridge (ink injection hole upward) above the table and shake the ink cartridge from top to bottom two to three times. So that the sponge in the cartridge can fully absorb the ink.

6. Wipe the cartridge nozzle with a paper towel, press the nozzle lightly with a paper towel, if the paper towel has ink, it can be installed and printed, and the label paper should be pasted back to its original place. If you don't get out of ink, hold the nozzle with a paper towel, shake it a few times into the air (nozzle down) to expel the air, and then wipe the ink cartridge overflowing ink, you can print on the machine, if you are not in a hurry to use it, put the ink cartridge back into the printer and let it stand for about ten minutes, and then carry out 1 to 2 times of "printhead cleaning", and then perform a test print or nozzle test.

7.In particular, it should be noted that the color cartridge should be operated carefully when filling ink by itself, so as to avoid the ink overflowing from the hole and flowing into other holes to cause color mixing. You can use a paper towel to absorb any excess spilled water before getting on the machine.

Turn off the power first, open the front panel cover, and remove the cartridge.

This toner cartridge is separated from the toner, the text is facing you, press the buckle in the lower left corner to remove the toner cartridge (one is the ink cartridge, the other is the cartridge holder), there is a round cover with a diameter of about centimeters on the right side of the cartridge, pry it out with a flathead screwdriver (don't pry it will leak powder).

Pour out the remaining powder inside, add a pair of toner covers of the model, there are 3 screws on the left and the gears inside, unscrew them, turn the gears in the arc hole to the other side (must be to the end), install the screws, the cartridge holder (there is a brown drum core on it), the round holes with a diameter of about 1 cm on each side of the shelf, and seal them with black (or opaque) tape.

Load the cartridge to the cartridge rack, load it into the machine, light the front panel cover, and turn it on.

??Let's open the front cover of the printer, take out the toner cartridge, there is a powder cartridge inside, you also find a way to take it out, there is a mechanism, you see for yourself, don't take it hard. Then look at the side with a white lid, you get it open, get the waste powder inside, get it out, you must clean it· It's OK to pour in the powder, if you don't fill the powder, just find a new powder bin and put it in. Begging.

The steps to add toner to Lenovo LJ2400L printer are as follows:

1. Remove the toner skeleton from the printer.

2. Press down the clip at one end of the toner skeleton, and then lift the skeleton to separate the toner cartridge from the skeleton.

3. This is the separated cartridge and skeleton.

4. There is a powder spout on the side of the compact, which is covered with a lid.

5. Use the tool chain to open this stamp, that is, the lid of the powder mouth.

6. Before adding powder, you need to pour out the residual waste powder.

7. Then add new toner and close the lid.

8. Put the cartridge back into the skeleton.

9. Replace the toner skeleton with the printer.

Summary. 3.Turn the gear on the lid of the cartridge counterclockwise to the leftmost position so that the cartridge is cleared, and if it is on the far right, the printer will assume that no toner has been added.

How to clear Lenovo LJ2205 printer after adding toner? Keep prompting to replace the cartridge.

Hello, I'm glad to answer for you, please later, I'm working hard to sort out the answer for you, and I'll reply to you within 5 minutes.

Hello, the clearing method is as follows:1First, use a screwdriver to remove the three screws on the right cover of the cartridge.

2.After that, the cover on the right side of the cartridge can be removed.

3.Turn the gear on the lid of the cartridge counterclockwise to the leftmost position so that the cartridge is cleared, and if it is on the far right, the printer will assume that no toner has been added.

It's my pleasure to help you! If you think it is helpful to you, please click on the "I want to rate" in the lower left corner to give a thumbs up. Finally, I wish you a happy life.

Lenovo printer LJ2200 still shows no toner after adding toner, the reason is that it is not cleared.

Tool Material: Take Lenovo printer LJ2200 as an example.

Lenovo LJ2400L printer powder can be cleared in the following ways:

1. First of all, it must be turned off, then open the front cover, press and hold the button on the machine with one hand, and turn on the switch with the other hand. (Note that you keep holding the start button to turn on).

2. All lights are on, and the lights are off when they are ready. After letting go, please press "2 times" in a row (you can only press it twice), then the full light will be on, and then press "5 times" in a row after letting go, close the door, and print normally at the end.

100 times more attentive, 10 points satisfied.

Please use the original consumables of the printer, substitute consumables or powder filling operations will cause damage to the equipment and be detrimental to your health, so it is not recommended to operate in violation of regulations.

Summary. Hello, 1. The printer is out of ink and cannot work, and the ink cartridge and toner need to be replaced.

2. Open the front cover, take out the toner cartridge, replace the toner, and don't rush to close the lid after changing the toner.

3. Carry out the clearance operation. We can see that there is a "Clear Back" button on the printer, press this button once first.

4. After pressing the "Clear Return" button, the options in the following picture will appear on the printer display, ignore it, but press the "Start" button quickly.

5. After pressing the "Start" button, press the "1" in the numeric keypad twice, remembering to press it twice.

6. After pressing, the display screen will appear in the following figure, ignore it. But at this time, the front cover can be closed, and then it can be printed.

Lenovo LJ2650DN printer always shows what to do if you replace the toner cartridge.

Hello, 1. The printer is out of ink and cannot work, and the ink cartridge and toner need to be replaced.

2. Open the front cover, take out the toner cartridge, replace the toner, and don't rush to close the lid after changing the toner.

3. Carry out the clearance operation. We can see that there is a "Clear Back" button on the printer, press this button once first.

4. After pressing the "Clear Return" button, the options in the following picture will appear on the printer display, ignore it, but press the "Start" button quickly.

5. After pressing the "Start" button, press the "1" in the numeric keypad twice, remembering to press it twice.

6. After pressing, the display screen will appear in the following figure, ignore it. But at this time, the front cover can be closed, and then it can be printed.