How to disassemble and assemble SAIC Maxus G10 thermostat?

When we replace the thermostat ourselves, we must pay attention to the direction in which it is installed, and the tip of the thermostat is facing upwards. If the orientation is wrong, the thermostat will not work properly, resulting in the failure of the self-regulating heat dissipation capability. At this time, the operating temperature of the engine must be lower than before, which will affect the thermal efficiency of the engine, resulting in the problem of insufficient power of the car.

Moreover, too low temperature will also cause poor fuel atomization, and it is easy to deposit a thick layer of carbon in the long run, which is very unfriendly to the fuel volume of the car. So, don't go in the wrong direction when you install it.

The disassembly method of Maxus Q10 glow plug is as follows:

1.The first thing you need to do is find the preheat plug, which is usually located above the engine block and connects the air intake tract to the air filter.

2.Using a wrench or torsion plate, remove the bolt next to the glow plug. The number of bolts depends on the model of the tank, usually 2-4 pcs.

3.Gently remove the glow plug from the cylinder block, taking care not to damage the gasket around the glow plug.

4.If there is carbon or dirt around the glow plug, you can use a brush or detergent to clean it.

5.When reinstalling the glow plug, apply a layer of gasket oil, then gently insert the glow plug into the cylinder body, install the bolts and tighten it with a wrench or torsion plate.

Why this answer is given:

The glow plug is an indispensable component for engine starting, and its function is to preheat the air in the intake tract and improve the success rate of engine starting. If the glow plug is faulty or damaged, it will cause difficulty or failure to start. Therefore, removing the glow plug for cleaning or replacement is an important step in maintaining the normal operation of the engine.

Practical solutions and countermeasures:

Removing the glow plug requires the use of appropriate tools and care is required to avoid damage to other engine components. Also, before removing the glow plug, you need to make sure that the engine has cooled down and the power supply has been disconnected to avoid accidents.

Extended Description: In actual operation, it may be encountered that the seal between the glow plug and the cylinder block is poor or the glow plug is damaged, resulting in the failure to start normally. At this time, the glow plug needs to be replaced in time to ensure that the engine can start normally.

At the same time, regular cleaning of the glow plug extends its service life and contributes to engine performance.

The Maxus Q10 glow plug is a small part installed on the drivetrain to ensure the normal operation of the engine during cold start. When replacing or repairing the Q10 glow plug, it needs to be removed. The specific steps to remove the Q10 glow plug are as follows:

First of all, you need to find a relative to the location of the glow plug. The location of the Maxus Q10 glow plug may vary depending on the model, and it is usually mounted directly in front of the engine or near the oil pan.

Next, use a wrench or other tool to loosen the set screws of the glow plug. It should be noted that before removing the glow plug, you need to turn off the power of the vehicle to avoid the risk of electric shock.

Finally, the glow plug can be gently removed. If the glow plug needs to be repaired or replaced after it has been removed, it is recommended to consult a professional technician for repair.

To sum up, to remove the Maxus Q10 glow plug, you need to first find the missing finger to its position, then unscrew the screw, and finally gently pull it out. It is necessary to pay attention to safety during operation, and it is recommended to seek professional help.

To remove the Chase Q10 glow plug, you can follow the steps below:

First of all, you need to have disassembly tools ready, such as wrenches, screwdrivers, electric drills, etc.

Secondly, remove the Maxus Q10 glow plug fixing screw, which generally needs to be unscrewed with a wrench.

The glow plug is then removed, usually with careful rotation and pulling.

Finally, if you need to replace the glow plug, you can install a new glow plug and reinstall the set screws and other parts.

It should be noted that when disassembling the glow plug in Huai Fu Hall, care must be taken to avoid unnecessary damage and injury.

The diesel version is generally one or two, and other general models have only one thermostat.

The thermostat is to automatically adjust the amount of water entering the radiator according to the temperature of the cooling water, and change the circulation range of the water to adjust the heat dissipation capacity of the cooling system and ensure that the engine works within the appropriate temperature range. The thermostat must be kept in good technical condition, otherwise it will seriously affect the normal operation of the engine. If the main valve of the thermostat is opened too late, it will cause the engine to overheat; If the main valve is opened too early, the engine warm-up time will be prolonged, and the engine temperature will be too low.

The function of the thermostat is to keep the engine from subcooling. For example, after the engine is working in this gear, the temperature of the engine may be too low if there is no thermostat in the winter. At this time, the engine needs to temporarily stop the water circulation to ensure that the engine temperature is not too low.

The following is the adjustment and installation of the engine cover: 1. Remove the engine cover, open the engine cover, and cover the body with a soft cloth to prevent damage to the topcoat; Remove the windshield washer nozzle and hose from the engine cover; Mark the hinges on the engine cover for later installation; Remove the fixing bolts of the engine cover which date is thick and hinge, and the engine cover should be prevented from slipping off after the bolts are removed; 2. The installation and adjustment of the engine cover should be carried out in reverse order of disassembly. Before tightening the fixing bolts of the engine cover and hinges, adjust the engine cover to the front and back, left and right, or adjust it up and down with the help of hinge gaskets and buffer rubbers to make the gaps fit evenly; 3. Adjust the engine cover lock control mechanism, before the engine cover lock is adjusted, the engine cover must be corrected properly, and then loosen the fixing bolts, move the lock back and forth, left and right, so that it is aligned with the lock seat, and the front of the engine cover can also be adjusted by the height of the lock dove tail bolt.

Summary. Hello, replace the water temperature sensor, directly unplug the connection of the water temperature sensor, remove the water temperature sensor and replace it with a new one, the function of the water temperature sensor is to convert the cooling water temperature into an electrical signal. After entering the ECU, there is:

1. The amount of fuel injection should be corrected, and the amount of fuel injection should be increased at low temperature; 2. Fix the ignition advance angle, increase the ignition advance angle at low temperature, and prevent detonation and delay when the temperature is high; 3. Affect the idle control valve, and the cryogenic ECU controls the action of the idle control valve according to the water temperature sensing signal to improve the speed rotation; 4. Affect the EGR valve.

Hello, replace the water temperature sensor, directly unplug the connection of the water temperature sensor, remove the water temperature sensor and replace it with a new one, the function of the water temperature sensor is to convert the cooling water temperature into an electrical signal. After entering the ECU, there are: 1. The amount of fuel injection should be corrected, and the amount of fuel injection should be increased at low temperature; 2. Fix the ignition advance angle, increase the ignition advance angle at low temperature, and prevent detonation and delay when the temperature is high; 3. Affect the idle control valve, and the cryogenic ECU controls the action of the idle control valve according to the water temperature sensing signal to improve the speed rotation; 4. Affect the EGR valve.

Where is the Maxus G10 water temperature sensor.

Hello, there is one near the pump, and the water temperature display on the dashboard measures the temperature measured by this water temperature sensor plug. In addition, there is an induction plug on the upper load tank and on the engine block.