What s going on with the Apple 4S automatically restarting as long as you swipe to unlock?

1. Click the slide unlock button, and then quickly double-click twice to enter the interface, three fingers at the same time to slide the screen to switch the interface, select settings, double-click the amount to enter, select the general double-click twice to enter, select the auxiliary settings, double-click twice to enter, and then turn off the vioceover function, and that's it.

2. First of all, install iTunes on your computer. Then launch iTunes.

3. Plug the data cable into your iPhone and connect it to the computer, press and hold Power (power button) and Home (the circle button below) for 10 seconds, wait for your iPhone to go black (according to experience, about seconds after the black screen), release the Power button, and keep holding the Home button until iTunes recognizes your iPhone.

4. At this time, Windows will first discover some new hardware and drive it by itself, and a prompt box will pop up after iTunes automatically recognizes the iPhone. "iTunes has detected an iPhone stuck in recovery mode, you have to restore this iPhone and then use it with iTunes. At this point, click OK.

Here's how:

Tap the slide unlock button.

Then quickly double-click twice to enter the interface.

Swipe the screen with three fingers at the same time to switch interfaces.

Select Settings and double-click to enter.

Select General, double-click to enter.

Select the secondary settings and double-click to enter.

Then turn off the vioceover function.

That's it.

Tap the slide unlock button.

Then quickly double-click twice to enter the interface.

Swipe the screen with three fingers at the same time to switch interfaces.

Select Settings and double-click to enter.

Select General, double-click to enter.

Select the secondary settings and double-click to enter.

Then turn off the vioceover function.

That's it.

Workaround:1In this case, you can tap the swipe unlock button once, and then quickly double-click twice to enter the phone interface.

2.Then select Settings - General - Auxiliary Settings - Vioceover function to turn off.

Once in a while, normal. (Flashing can be solved).

If the number of restarts is frequent, it's a hardware issue. (The faults I have touched are: reboot caused by damage to the tail plug cable, reboot caused by CPU failure).

Good luck. Hope it helps

Reasons why iphone4 automatically shuts down:

1: The motherboard is faulty.

2: The system version is buggy.

It is recommended to restore the system version to fix the bug issue.

Step 2: Connect your iPhone4 to your computer with a data cable.

Step 3: In the summary interface, click "Restore iPhone" and follow the iTunes instructions to restore the system version.

The iPhone 4 is only millimeters thick, which is 24 percent thinner than the iPhone millimeters. The iPhone 4 has incorporated a dual MIC design, one of which can play the role of active noise cancellation, which will greatly improve the call quality of the iPhone 4.

The iPhone 4 uses a display technology called Retina, and the iPhone 4 uses a display screen with a resolution of 960x640 pixels, which is equivalent to 78% of the pixels of an iPad screen. Since the screen size has not changed, it is still inches, and the increase in resolution increases the display resolution of the iPhone 4 to four times that of the iPhone 3GS.

Try their methods first, and contact me if it doesn't work.

Click the slide unlock button, and then quickly double-click twice to enter the interface, three fingers at the same time to slide the screen to switch the interface, select settings, double-click the amount to enter, select the general double-click twice to enter, select auxiliary settings, double-click twice to enter, and then turn off the vioceover function, ok.

If there is a problem with the system, just go to the repair point and redo the system.

Brush the phone with iTunes, if it's a system problem, it should be solved. If it's hardware, no one can help you.

Volts and analysis with friends:

1.Program errors, process conflicts, etc. caused by jailbreaking.

2.The phone's hardware is damaged, causing the instructions to get out of control.

3.Genuine firmware problems, there are bugs that have not been fixed.

Solution:1Flash the latest firmware and fix the bugs.

2.The Bank of China and the Bank of Hong Kong are under insurance, and non-man-made damage can be replaced by Apple after-sales service, and the remaining payment fee for the lack of traces can be replaced.

3.Same as option 1.

Generally, in this case, the power on and off button is broken. Replacing the on/off button can solve the problem.

Reasons and solutions for the automatic restart of Apple 4S mobile phone:

1. If you have jailbroken, it may be that the plug-in is incompatible.

Solution: In the case of normal shutdown, first press and hold the power button to shut down, (if it can't shut down normally, try to press and hold the power button and add home to force shutdown), after shutting down, press and hold the power button and the volume + key to power on, when the white apple logo appears after powering on, immediately release the power button, volume + key and hold on, until the boot, uninstall the jailbreak plug-in.

2. The boot button is damaged, or the contact is poor, and the contact is oxidized.

In summer, everyone puts the battery in the pocket or bag, or the air in the coastal city is humid and salty, which is easy to oxidize the contacts, resulting in the battery being connected to the false or false battery, not being fully charged, or not durable.

Solution: Replace the power button and wipe the contacts with a cotton swab dipped in alcohol.

3. The battery is loose.

If the battery is very loose and does not touch well, it will restart, and it will be connected again at the moment of disconnection, so it will automatically restart.

Solution: Check the power cord plug in, and use tape to thicken the phone case directly behind the battery contact, pay attention not to be too thick.