Model ZXV10 H108L Tianyi broadband router set

Hello: You open the web page.

Log in with the password of the super network management account and open the network - broadband settings.

Establish a new connection, carry the service Internet (enabled), the mode route (PPPoe), use NAT, enter your account and password to access the Internet, and confirm.

We'll be happy to answer for you.

Choose ADSL Virtual Dialing (PPPoE), Internet access and password is your broadband account and password. Restart your computer when you're done.

Wholeheartedly answered, I wish you great satisfaction.

How to set up a wireless router:

1. Open the browser, enter the IP address of the router gateway in the address bar, and the username and password are generally admin (lowercase) if they are not changed;

2. After successful login, the running status will be displayed, click "Wireless Settings";

3. Click "Wireless Security Settings" again, and the wireless network name (SSID) is a name, which can be filled in casually, generally letters + numbers;

4. Then set the password, generally choose the WPA-PSK WPA2-PSK encryption method (the password should be 8-16, and the alphanumeric combination can be used);

5. After setting the password, click Save to prompt restart;

6. Click "Restart Router" in "System Tools" to restart the router.

Telecom Tianyi ZTE ZXV10 H108L wireless routing setting method:

1. Enter the IP address indicated on the label behind the modem into the address bar of the browser and log in to the modem settings page.

2. Click "Network" and select "WLAN Configuration".

3. Scroll down to the end and click the "Advanced" button;

4. To set up the network authentication mode, it is recommended to use "WPA2-PSK", then enter the password you want to use, and finally click the "Save Application" button to save the configuration;

5. Finally, in the "Management" - Device Management" column, click "Restart Device" to restart.

The book is searched.,And you have to point to a broadband connection.,Because this cat doesn't have a dial-up.,So the book also needs to point to a broadband connection to dial-up the Internet.。

Telecom broadband (ZXV10 H108L) router with a mobile phone to connect to the wireless network method: ZXV10 H108L is the telecom optical modem to turn on the WiFi method:

Turn on the router's wireless function].

1. Enter the router:

Open the browser, enter the general router address in the address bar is this or check the login information on the back of the router) Enter the route - enter the user name, password, (the default is generally admin).

2. Select Wireless Settings --- Basic Settings.

3. Check [Turn on wireless function] and click Save.

Set wifi password].

1. Enter the router:

Open the browser, enter the general router address in the address bar is this or check the login information on the back of the router) Enter the route - enter the user name, password, (the default is generally admin).

2. Wireless Settings - Wireless Security Settings - Select [WPA-PSK WPA2-PSK].

Authentication Type: Automatic.

Encryption algorithm: AES.

The PSK password is the wireless password. Set the required password.

Because H108L does not route dialing, and the mobile phone does not have PPPOE dialing, it will definitely not be able to access the Internet, and your mobile phone is just connected to the LAN.

To crack the H108L routing function and let it dial automatically, the mobile phone can be connected to the wireless LAN directly.

Try setting the router wireless connection password to WPA type.

If the user should have handled the ITV service of Telecom, it will be debugged and used normally after the telecom staff completes the installation.

If you forcibly configure the routing function of the wireless modem, the normal use of the ITV of the device may be affected.

If you need to use the WiFi network, it is recommended to install a wireless router.

1.Plug the broadband modem or home network cable into the WLAN port of the router, and then connect to the computer through the network cable or wireless network.

3.After entering the page, you will be prompted to enter the management account, which also needs to be found in the manual, and the general account password is admin.

4.Click the Setup Wizard, follow the prompts on the page to set up broadband without oppoe dialing, and enter the broadband account password.

5.According to the prompts on the page, check the box to turn on the WiFi network, and set the password, when finished, click Next, and the device will automatically restart.

All I know is that I didn't crack it, press the remote control setting key to change the wired connection to a wireless connection.

The output of the ITV is bound to a network port, and it must be exclusive to this port. It is recommended that you use an ITV cable to connect to the TV set-top box and use wireless Internet access.

If you want to use ITV wirelessly at the same time, you must purchase two more wireless routers, one connected to the ITV output port of ZXV10 H108L, and one connected to the set-top box (if your set-top box wireless network card can be used, this does not need to be bought).

AP1 (use the LAN port to connect to the ITV port of ZXV10 H108L) DHCP: Enabled.

LAN Settings: IP:

Wireless working mode: WDS

SSID: AAA (renamed to make it easier to distinguish).

AP2 (use the LAN port to connect to an IPTV set-top box or a wireless network card of the set-top box) DHCP: Disabled.

LAN Settings: IP: Gateway: IP pointing to AP1) Wireless Operating Mode: WDS

SSID: BBB (renamed to make it easier to distinguish).

Wireless Distribution System (WDS) for AP1: Scan to MAC of AP2 and add Wireless Distribution System (WDS) for AP2: Scan to MAC of AP1 and add.

How to set up wireless wifi on a wireless router:

1.The router is connected to the network, and the computer is wired to the wireless router.

2.Go to the gateway page.

Open a computer browser and enter the gateway IP address of the nameplate on the back of the router (generally, enter the gateway configuration interface.

3.Set the wifi name and password.

Go to Wireless Security in the Wireless Settings and select WPA2-PSK mode for Security Mode. Select AES for WPA encryption rule. Set up a wireless network key. The router will automatically restart after setting, please enter a new wifi password to connect.

One changed to an auto-routed dial-up cat.

Password: ne7ja%5m (Note: The password should be cased, it is recommended to copy and paste it if it is more complicated, and there should be no spaces).

2.After logging in, click "Network" first (and then select "Connection Name", delete them all one by one, pay attention to them when deleting, delete them to that one, and the connection will be dropped, your VPI VCI is that For example, when you delete to Interner B 0 35, it will be disconnected, then your VPI VCI is 0 35, record it yourself, and use it later).

3.Then select the connection name: "New WAN connection," then select the route mode, click PPPoE, enter the local VPI and VCI parameters, fill in your broadband account password, and service mode:

Internet, point to create, be careful not to restart it first Telecom may be monitoring your cat See below.

Commonly used VPI VCI: Yuanjiang's is 8 88 (very important).

How to set up Wi-Fi:

1. First open the control panel, open it in the start menu.

2. After opening the control panel, find the option of Network and Sharing Center, and then open it.

3. After opening the Network and Sharing Center, there is detailed information about network connections. Click on the blue link in the middle of the settings for a new connection.

4. There was a network connection on the computer before, if you want to reset a wireless network connection, choose the first option, no, create a new connection. Then click Next.

5. In the page of selecting the connection method, if there is a wireless network, a wireless connection option will be displayed in the list below. Click on this option with your mouse and click OK.

6. After clicking OK, go back to the system tray, find the icon of the network connection, then open it, select the connection, click on the following options to set the wireless network, enter the network name and security key, and click OK.

I got it for a few hours, and finally turned on the wifi, and at the same time I got on three wireless phones, this book, ipad, and desktop

Enter the cat user name telecomadmin

Super password ne7ja%5m

Connect, delete one by one, see which one you use now, remember.

2.dot to establish a new connection. Select the route mode pppoeEnable NAT (i.e. tick). The business model is Internet

3. Enter the local VPI and VCI parameters, which is the WAM connection that you want to remember, e.g. (0, 32...).0/35...And so on).

4. Fill in the account password· Don't play this if you can't do it.

5. Save & Restart

6. Set the wireless connection password...

7. After setting up, change the remote management in the network ** in the first line, delete the username and password, remove the tick of periodic reporting, and then click on the middleware working mode on the right and select "Enable middleware, excluding TR069 function (control function of telecommunications)".

Don't use the cat's own set parameters too many directly connect your own wireless router to the WAN port, and then enter the router setup wizard, enter the account and password of the broadband connection into it, and follow the prompts to next step until it is completed, save and restart the route.

Go to reconfigure via Super Admin.

Note: The super administrator password of the Unicom device and the telecom equipment of the ZXV108L is different, and the input is case-sensitive, so you need to enter it in the English input state.

Unicom version——:cuadmin

Password: cuadmin

Telecom version -: telecomadmin

Passcode: ne7ja%5m

Configuration process (also known as cracking):

1. Connect the device and the computer correctly, and it is best to use a horn cable (that is, a network cable) to connect.

2. Close all other programs, and it's best to log out of the computer.

3. Open IE Browser, clear the address bar, and directly type "not more, not less."

4. In "Network - Broadband Settings - Connection Name", delete all connections except "New WAN Connection" until the "New WAN Connection" item is left in the "Connection Name" drop-down menu (select the connection you want to delete, there will be a delete option in the lower right corner).

5. Create a new w an connection, and all parameters not mentioned are defaulted.

Business model: Internet

New VPI VCI: The VPI VCI for your city

Username: Your broadband.

Password: Your broadband password.

Configure as shown in the figure below (check all 8 ports bound, otherwise the network will be unstable and often dropped), click Create after the configuration is completed, and then your computer should be able to connect to the network.

6. In "Network - WLAN Configuration", you can set the name and password of your own wireless network.