How to remove the filter screen of Hisense air conditioner? How to remove the filter screen of Hisen

Remove the front panel of the air conditioner, cut it directly, and lift it upwards to see two filters.

The air conditioning filter is a concave-convex honeycomb structure, which can be widely used in air filtration and sewage filtration systems, and the antibacterial agent (DEP) and antifungal agent (TBZ) are directly incorporated into the PP resin raw material in the spinning stage, so that the filter screen produced has achieved the antibacterial and anti-mildew effect.

It is easy to wash and change multiple times, and the onset time is long-lasting.

Type: 1. Vertical air conditioning filter It contains three layers: dust removal screen, activated carbon screen, and reinforced screen, which is recommended to be replaced every 1-2 months.

2. Bedroom air conditioning filter It contains activated carbon mesh and reinforcing net, which is recommended to be replaced every 1-2 months.

Instructions for use: 1. The air filter in the indoor unit of the air conditioner is generally in a normal use environment, and the validity period is 6 months.

2. If the air conditioner is not used frequently, the use environment is good, and the air cleanliness is high, as long as the surface of the air filter does not have serious discoloration (gray-brown), the air filter can be taken out and exposed to the sun for 2 hours, and the dust on the surface can be reused after being cleaned with a brush (can not be cleaned with water).

1.Turn off the power on the air conditioner.

2.Remove the front panel of the air conditioner, cut it directly, and lift it upwards, and you will see two filters.

3.Remove the filter and flush it directly with tap water from the water pipe.

4.Put it in a cool place to air dry, the filter is generally plastic, do not put it in the sun directly.

5.Wipe the dirty areas inside the air conditioner, install the filter back inside the air conditioner, and fasten the front panel.

Hisense air conditionerHow to remove the filter:

Tools Raw materials: Hisense air conditioner, brush.

Method Steps:

1. Before disassembling the air conditioner filter, carefully open the air conditioner shell, generally there are two small card slots stuck, and the outer cover can be cut out lightly.

2. After opening the outer cover of the air conditioner, there are often two buckles inside, and it is necessary to gently open it to make the outer cover fully open. Lead rock wide.

3. The filter screen is relatively easy to take, but it is stuck by a few card slots, first push the filter screen up, and then gently take out the filter screen after the lower end is out of the card slot.

4. After removing the filter, we gently rinse the filter with water several times, and we can scrub it several times with a soft brush.

5. Wait until the filter screen is dry, and install it according to the previous steps.

Hisense cylindrical air conditioner belongs to cabinet air conditioner, so the way to remove and wash the filter screen is different from that of hanging air conditioner. Here's how it works.

Turn off the power socket of the air conditioner room, lift both ends of the air conditioner's shell to open the shell, and then lift the shell above the air conditioner (the shell can be automatically stuck and fixed, so you don't have to worry about falling off).

There are 2 plastic frames (one on the left and one on the left) inside, and you can remove the filter by gently pushing it up by hand, rinse the filter directly with water, and then dry it and install it back into the indoor unit as it is.

Turn on the power and turn off the air conditioner. Select the BAI cleaning function Gently sweep the palm of the hand over the black induction of the panel, click the function key, select cleaning, and then press the " " or " " button to confirm, the cleaning pattern is bright. At this point, the shell starts to rotate automatically, and after about 27 seconds.

The housing stops rotating, and at this point the filter has been turned to the front of the air conditioner, and then the power supply to the air conditioner is cut off. Remove the air inlet panel.

Use a screwdriver to unscrew the screws that hold the air inlet panel in place, and break the two buckles of the air inlet panel. Remove the air inlet panel. Remove the filter and pull out the filter in the direction of the arrow. Wash the filter.

Turn on the power, tap the function, then click Clean, and then click the up or down arrow icon, so that the air conditioner will automatically rotate to the filter screen to be exposed, and then use a screwdriver to unscrew the fixing screw on the filter screen cover, remove the screen cover, and finally pull out the filter screen for cleaning.

1、You can find a square cover plate at the bottom right of the Hisense washing machine,As shown in the figure below。

2、After that, use the one-yuan coin to insert it into the small hole bought on the cover of the Hisense washing machine,Stuck the coin,As shown in the figure below。

3. After that, pull outward to open the lid below, as shown in the figure below.

4. After that, press and hold the knob inside with your hand and rotate it clockwise, as shown in the figure below.

5. In this way, the filter screen of the washing machine can be removed, as shown in the figure below.

1. First of all, in order to prevent electric shock and leakage, you need to turn off the power socket, or you can directly unplug the socket, which is very important;

2. Then open the shell of the air conditioner upward, with a very light force, special attention should be paid to the fact that if you find that it is not easy to open by hand, you can use a screwdriver to help, do not use brute force, to master the skills, otherwise it is easy to damage the shell of the air conditioner;

3. After opening the shell and then lifting it above the air conditioner, the air conditioner shell can be automatically stuck and fixed, so you don't have to worry about falling off; At this time, you can see that there is a plastic air conditioning filter inside, which is the part that loves to hide dirt and dirt;

4.You only need to gently push the filter up with your hand, and then remove the filter screen;

5 Put the strainer in the basin and rinse it directly with water.

6. Then add an appropriate amount of warm boiled water to the basin and soak for an hour, as shown in the figure below;

7 After an hour, clean the filter with clean water;

8 Finally, put the cleaned filter on the balcony to dry.

It's just that you can just lift the panel, and the plastic of the air conditioner is resistant to deformation and won't break. Pull hard, and it's open, and then pull out the filter inside. It's simple.

I'm really not at ease,You can contact Hisense's after-sales service,They will have professional staff to guide the operation,

Hisense washing machines come in two forms, both drums and sleeves. It's not the same to remove the filter, and the drum is not at all.

The drum washing machine is not equipped with a suction plate, because it adopts the form of a direct water pump, which is not sensitive to capillaries.

However, sometimes there will be larger dirt that cannot be discharged, which generally accumulates in the lower mouth of the drainage pump. Or check the lower drain for dirt.

Sleeve washing machine, then there is a filter, as long as in the top groove of the filter frame, use your fingers to pull out, you can pull out, and then lift up, and take it out.

<>How to remove the Hisense cabinet air conditioning filter:1、Open the air conditioning shell,There are usually two small card slots stuck,Gently pull the outer cover of the silver outward。 2. After opening the outer cover, pick open the two buckles inside, and completely open the outer cover.

3. Take off the filter, change or talk about the general filter screen is stuck by the card slot, just push the filter screen up gently, and then pull it off with your hand.

Summary. Haier cylindrical air conditioning filter disassembly and assembly**21, when disassembling and installing, it is necessary to cut off the power, this is to ensure personal safety, and then in the state of air conditioning shutdown, press the function button, and the cleaning pattern of the shower head icon flashes. 2. Press the up or down button to confirm after the shower head flashes, the cleaning icon will light up, and then the shell of the air conditioner will start to rotate automatically, and stop after about half a minute.

3. At this time, the filter screen will be transferred from the back to the front, and then we will unplug the power cord of the air conditioner, use a screwdriver to remove the screws on the panel one by one, and then break the upper and lower buckles, remove the air inlet panel, and pull out the filter screen to the right.

Hello dear! According to your description, I give the following conclusions and methods: different brands of cylindrical air conditioners, or different models of air conditioner filters have different removal methods, as follows: Haier cylindrical air conditioner cleaning Yan Wang Ruchang filter method 1:

Haier cylindrical empty bush laughing filter disassembly **11, put both hands on both sides of the blind combustion air conditioner in the recessed place. 2. Press down the buckle with both hands at the same time. 3. Open the air inlet grille upwards, and you will see the filter inside.

4. Gently press down on the protrusion in the center of the filter to get it out of gear, and then pull down the filter screen.

Cylindrical air conditioner disassembly method two:

Haier cylindrical air conditioning filter disassembly and assembly of the shirt Xiang **21, when disassembling and installing, it is necessary to cut off the power, this is to ensure personal safety, and then in the state of air conditioning shutdown, press the function button, and the cleaning pattern of the shower head icon flashes. 2. Press the up or down button to confirm after the shower head flashes, the cleaning icon will light up, and then the shell of the air conditioner will start to rotate automatically, and stop after about half a minute. 3. At this time, the collapsed rubber filter will be transferred from the back to the front, and then we will unplug the power cord of the air conditioner, use a screwdriver to remove the screws on the panel one by one, and then break the upper and lower buckles, remove the air intake panel, and pull out the filter screen to the right.

Precautions for cleaning and removing the filter screen: 1. The removed filter screen can be cleaned with clean water as soon as it is burned, and the water pipe is rinsed with tap water, and no other detergent is needed. 2. The clean filter screen can be carried and dried in a cool place, and it is best not to be exposed to the sun, the filter screen is generally plastic, and it is easy to be damaged by exposure.

3. The clean filter screen can be installed directly and then installed, the installation steps are the same as the removal steps, and the dust inside the air conditioner can be scrubbed clean before installation.