How to wire the single open multi control switch, how to wire the single open multi control

One-on-multi-control switch refers to a switch that is composed of two single-open and dual-control switches on a switch panel, and the two single-open and double-control switches are controlled by a rocker at the same time.

This switch can realize the control of lighting in an infinite number of locations, the principle is that the multi-control switch itself is an AC 220V single-pulse bistable circuit system, the multi-control switch is responsible for controlling the lighting load, the sub-switch is responsible for providing pulse signals to the multi-control switch, the sub-switch can be used with an ordinary doorbell switch, can not use a single-link single-control rocker switch.

At this time, the multi-control switch gets a pulse signal to turn on the load, and then gets a pulse signal to turn off the load. The multi-control switch can be installed in the lamp or on the wall, leading out two signal lines in parallel sub-switches, wiring design is quite convenient and economical, no matter how many sub-switches are only connected in parallel with two thin wires, as long as you click on any sub-switch, the lighting load can be turned on and off.

The wiring diagram of the one-on-open multi-control switch is as follows:

The two ends are connected to the live wire with the L end of the first single control switch, the L1 end and the L2 end are connected to the two L ends of the double control switch respectively, and the two L2 endpoints and L3 endpoints of the double control switch are connected in series to the two L-end ,...... of the second double control switch respectivelyIn turn, follow the connection of the first single-control switch and the double-control switch, and finally use a single-control switch.

How to wire the multi-control switch? There are many ways to connect it, and it's very simple.

Answer: First of all, the two switches should be connected with wires, the live wire is connected to a switch line post, the other line post is connected to the lamp, and then the other side of the lamp is connected to the zero wire, and finally the power switch can be opened to try it.

1. When the switch socket is opened and used, it should be noted what it is for, usually the plug of the electrical appliance will be plugged into it first, and then the switch will be turned on.

2. When using the switch socket at ordinary times, you don't need to pull out the plug every time, and you can't close the switch, so as to ensure its safety, if you don't need this appliance for a long time, you can turn off the switch, and pull out the plug to prevent all kinds of accidents.

3. When the electrical appliance is plugged into the socket, the switch cannot be turned off directly, and when the electrical appliance is used, it will also bring damage to the quality of the electrical appliance, and there will be poor contact, which will also lead to a reduction in life. If necessary, the appliances must be turned off, and the plugs can be turned off before they can be unplugged.

4. If it is a thunderstorm, the safety protection measures must be done, do not use electrical appliances, but also turn off the switch, and at the same time unplug the socket, or it may be struck by lightning, which will be very troublesome.

Hope it helps, dear

The wiring diagram of the one-on-open multi-control switch is as follows:

This switch can realize the control of lighting in an infinite number of locations, the principle is that the multi-control switch itself is an AC 220V single-pulse bistable circuit system, the multi-control switch is responsible for controlling the lighting load, the sub-switch is responsible for providing pulse signals to the multi-control switch, the sub-switch can be used with an ordinary doorbell switch, can not use a single-link single-control rocker switch.

Function. The multi-control switch can control the lighting in an infinite number of locations, the principle is that the multi-control switch itself is an AC 220V single-pulse bistable circuit system, the multi-control switch is responsible for controlling the lighting load, and the sub-switch is responsible for providing pulse signals to the multi-control switch. In this way, the multi-control switch gets a pulse signal to turn on the load, and then gets a pulse signal to turn the load off.

The multi-control switch can be installed in the lamp or on the wall, leading out two signal lines in parallel sub-switches, wiring design is quite convenient and saving, no matter how many sub-switches are only connected in parallel with two thin wires, as long as you click on any sub-switch, the lighting load can be turned on and off.

If it is used as a single control switch, connect the live wire to the L interface, and connect the lead wire to the L1 interface.

If you want to control a lamp at the same time with a dual switch in other positions, you can use it in the following connection:

Regarding how to wire the double open and double control when the single open and double control is as follows; 1. Single-open and double-control switch, there are three contacts behind it, which are L, L1 and L2. Connect the two L1 and L2 with wires respectively, the live wire is connected to the L contact of one dual-control switch, and the neutral wire is connected to the L-contact of the other dual-control switch. 2. Single open and double control is one of the electrical switch control methods, which are divided into single open and single control, single open and double control, and double open and double control.

The SPDT switch has two functions: one is to control the power supply to output to two devices separately. Second, it can control a device for different output forms.

Hope it helps, thank you.

When the single open and dual control is connected, how to connect the double open and dual control? The suggestions on how to connect the double open and dual control when the single open and double control are as follows: 1.

Single-open, dual-control switch with three contacts on the back, namely L, L1 and L2. Connect the two L1 and L2 with wires respectively. The Firewire is connected to the L-contact of one dual-control switch, and the neutral wire is connected to the L-contact of another dual-control switch.

2.Single-open and double-control is one of the control methods of electrical switches. It can be divided into single open and single control, single open and double control, and double open and double control.

The SPDT switch has two functions: first, it can control the power output to two devices separately. Second, it can control a device to generate different forms of output.

I hope I can help you, thanks.

Dual control is connected by single and double control, and when double is opened, single and double control is connected, and it is recommended as follows; 1. A double circuit breaker, there are three contacts behind it, respectively L, L 1 and L and L-2 two lines are connected to each other, the ignition wire is connected to the L contact of the double switch, and the zero point is connected to the L contact of the other double control switch. 2. Single and double control is one of the control methods of electrical switch, including one-way control, single start, single open and double control, double control, etc. Two actions of a single-pole switch:

First, the energy output of the two devices can be controlled separately. Secondly, the device can be controlled in a variety of output forms. Thank you for your help.

Directly above the picture, if you don't understand, please ask.

The wiring method of Schneider dual control switch is as follows. The holes marked with L1 and L2 are common terminals, and the holes marked with L11 and L12 are connected to the lamp head wires (the two holes are connected to one at will). The hole marked L21 and L22 is connected to the control line of 2 lamps (two holes, any one), and the dual control switch is a switch with two contacts (that is, a pair) of normally open and normally closed at the same time.

Usually two dual-control switches are used to control a lamp or other electrical appliances, which means that there can be two switches to control the switch of electrical appliances such as lamps and lanterns, for example, turn on the switch when going downstairs and turn off the switch when you go upstairs. If you want to turn off the lights, you have to run downstairs to turn them off, and you can avoid this trouble by using dual-control switches.

Question: I asked about the halfway switch with double opening and multiple controls.

Answer 1: Turn off the main knife switch. 2. Prepare two dual-control switches (each dual-control switch has up, down, right, three contacts); a bundle of red wires for fire; A bundle of blue wires for the neutral wire, and a bundle of green wires for the control wire. 3. First of all, open the switch box of these two switches, install the two switches on the wall according to the normal position and height, connect the upper and lower contacts of the two double control switches with two green wires, when connected, the two switches are placed in front, the upper contact is connected to the upper contact, and the lower contact is connected to the lower contact to make a back and forth control line.

4. Use a red wire to connect the right contact of the switch downstairs (if the switch downstairs has a socket on the left, then this wire can be changed to a brown or black wire), and finally check it.

Question: Schneider double-open multi-control midway switch.

What profession [rage] [rage] [rage] [rage] [rage].

And no.

Ask a question. Answer hello, 1Multi-control switch (intermediate switch) The multi-control switch is a combination of two dual-control switches (single-pole double-throw switches), and the two dual-control switches share a rocker to achieve linkage; Two of its six terminals are fixed and built-in, so that the standard multi-switch has only four terminals.

A2The purpose of installing three switches is: one switch in K1 and K2 jointly controls a certain lamp; Another switch in K2 and a switch in K3 work together to control the bedside lamp; Another switch in K3 controls the main light in the bedroom. So, it's not three switches.

2. After determining the switch binding post, use a section of wire to connect the L11 and L1 of the switch to the source.

3. After the above picture is connected, connect the red live wire to L1 and turn on the power of the switch.

4. After the power is turned on, connect the two white control wires of ZD in the cassette to L2 and L21 respectively.

5. In this way, the line of the dual-control switch is connected, and the switch of the connected line can be fixed to the wall.

The multi-control switch itself is an AC 220V single-pulse bistable circuit system, the multi-control switch is responsible for controlling the lighting load, and the sub-switch is responsible for providing pulse signals to the multi-control switch. ）

You can wire according to the wiring diagram of the double-control switch below:

Connect the L1 terminal of the switch (the inlet of the live wire) to the L1 terminal of the switch, connect the L1 terminal of the switch (the outlet port of the live wire) with the L1 of the other double control switch, then connect the L2 of the switch with the L2 of the other double control switch, then connect the L3 terminal block of the other dual control switch (the live wire terminal) to the live wire end of the bulb, and connect the neutral wire to the neutral end of the bulb.

How to wire the multi-control switch? There are many ways to connect it, and it's very simple.

Summary. Hello dear! Multi-control switch wiring method 1

First of all, connect the incoming live wire to the incoming end of the dual control switch L,2Then find two wires, connect the two wires one to L1 of the dual control switch, and one to L, 3Next, connect the two wires connected to the multi-control switch L3 and L4, and the two wires at the same end are connected to L1 and L2, 4

Next, use two wires to connect L1 and L2 of another dual-control switch, how to wire the multi-control switch?

Hello dear! Multi-control switch wiring method 1First of all, connect the incoming live wire to the incoming end of the dual control switch L,2

Then find two wires, connect the two wires to the double control switch of the Xianxiao Ju L1, and one to the L, 3Next, connect the two wires connected to the multi-control switch L3 and L4, and connect the two wires at the same Shenxun end to L1 and L2, 4Next, use two wires to connect L1 and L2 of another dual-control switch, and how to wire the switch in the middle of the three-control switch.

1. Prepare three switches first, if the wire is open, two one-open dual-control switches and one double-open dual-control switch. 2. The live wire and the single wiggle control switch shed Cha L phase chain are connected, the control line L1 and the L1 are connected with the L1 of the dual control switch, and L2 is connected with the L2 of the double control switch. 4. The left L1 of the double control switch is connected to the right switch L2, and L2 is connected to L1.

5. The L that is drawn out is connected with L1 and L2 of the third single-control switch. 6. Then lead out the L of the third single control switch to the lamp holder, and the lamp holder is connected to the zero line with another wire, so that the three control lines are done.

Dual-control switch: The first is a more common connection method, and the principle of dual-control is also clear, clear and intuitive.

The second wiring method seems to be more complicated than the previous one, but the principle of zhidao's dual control to control the lighting is the same.

Third, this is also a common dual-control switch connection.

The above two wiring methods are the wiring methods of the switch with a three-pin socket, which can be referred to below.

The three-control switch is to use three switches to control an electrical appliance, and another switch needs to be added in the middle. The switch in the middle may not be easy to buy, we will replace it with a double-open double-capacitance switch, let's take a look at the wiring of the three-control switch:

It looks a little complicated, but it would be nice if you could buy that kind of special switch for three control switches in the middle.

Taking the dual-control switch as an example, the wiring method of the multi-control switch is:

When wiring the dual control switch, first connect the wire between the two switches, that is, the yellow wire part is connected;

Next, connect the live wire to the access points of the two dual-control switches.

There is no exact answer to this question, so ask the people around you if they know about it. Have a great day.