How to set the IP bandwidth control of TL WR941N?

4m line,Each person is allocated 100-120kb,That is, 800-960kb,The reason why this distribution is because not every machine will use so much time,If you directly calculate the average,It will be very wasteful,100-120kb rate look**,**Movies are enough,And it will not cause a large network resource occupation,We are 7 people with 2m line,I give each person 90kb,Chat,Send and receive emails,Open a web page is enough,Look** If you want to watch a movie, you can watch it in normal quality. In particular, it should be added that the uplink bandwidth of ADSL can not be 4M, the 4M of ADSL refers to the downlink bandwidth, the uplink bandwidth of ADSL is only 512KB now, and the maximum of ADSL2+ is only 1M, so the uplink bandwidth must be limited, each machine is limited to 30-40KB, and the number of concurrent connections is limited to about 150, otherwise the uplink bandwidth will be occupied, your data cannot be sent or the delay is large, your bandwidth is set there, that is, the first figure, The uplink should be set to 512 and the downlink to 4096.

TL-WR842N Router Setup IP Broadband Control Method:

2. Enter the correct username and password to enter the router management background.

3. We need to check the existing IP and the corresponding MAC address bar first. Click "DHCP Server" on the left, select "Client List", and write down the corresponding IP and MAC addresses displayed on the right.

5. Enter the correct corresponding MAC and IP address on the right, then select "Status" as "Effective", and then click the "Save" button to save.

6. Repeat the previous two steps until all IPs are added.

7. Click the "IP Bandwidth Control" link on the left, check the "Enable IP Bandwidth Control" checkbox on the right, and select the correct network speed below.

8. Then fill in the IP and bandwidth size to be controlled in the following rules, and also set your own computer "Guarantee minimum bandwidth", and select "Enable" for all, and then click the "Save" button to save all the settings.

3All Use the IP address, username, password (there is a prompt on the back of the router), and enter the browser address bar.

DHCP Service Client List to view which clients need to be blocked or rate-limited.

IP Bandwidth Control Add a new entry (refer to the message above) Fill in the IP address and uplink and downlink bandwidth (reasonably allocated according to demand) Enable Save Reference Materials "Route Control Bandwidth.

Enable IP bandwidth control.

Total uplink bandwidth: (640) kbps

Total downlink bandwidth: (2048) kbps

It can actually be added to the big one, but it's useless.

Address Segment I don't know how to set up your DHCP service, fill it in like this, don't worry about the port segment.

Bandwidth per person half of the words uplink:

Down: (0) (1050).

If you want to subdivide, you need to assign a static address.

First, record the network card through the client list, and ctrl+c can be copied to subdivide it.

Generally, check the MAC addresses of the two computers, and then check the IP corresponding to the MAC address in the router DHCP customer list.

1. Set the line parameters.

On the management page, click IP Bandwidth Control, select Enable IP Bandwidth Control, and select ADSL Line Type with a bandwidth size of 4096. As shown below:

2. Add a rule for desktops.

Enter all IP address ranges. Mode selection Limit the maximum bandwidth, and set the bandwidth to 3000. Add the corresponding note information and check Enable.

3. Set rules for other terminals.

Enter all IP address ranges. Mode selection Limit the maximum bandwidth, and set the bandwidth to 2000. Add the corresponding note information and check Enable. When you're done, click Save.

Here's how to set up IP broadband for the TL-WR740N router:

1. The default management address of Mercury router is, enter the IP address of the router on the Internet Explorer, then enter the username and password of the router, and click the "OK" button.

2. After entering the router management page, click "IP Bandwidth Control" in the list on the left side of the page, and then check the "Enable IP Bandwidth Control" option on the right.

3. Then select the type of bandwidth, here select the broadband type as ADSL, and the bandwidth size is 2000 kbps.

Note: Please enter the bandwidth size according to your actual situation, the default value is 2000kbps

4. Next, configure the IP bandwidth control rule

1.The rules are controlled by IP address ranges, for example, if you enter 100-150 here, this means that these IP addresses will be controlled by this rate limiting rule.

2.Select Limit Maximum Bandwidth as the mode and select Enable.

3.The bandwidth size is set to 100 kbps, which means that the maximum speed cannot exceed 100 kbps. Please set it according to your actual situation, if the speed limit effect is not ideal, you can adjust this value slowly. After the adjustment, click Save.

This kind of cheap router, its speed limiting function is simply useless. It is a card when I set it.

Go to ** on the Tao hard change 2805 .

1.How to set bandwidth control:

Click the "IP Bandwidth Control" menu, where you can set different modes and bandwidth rental sizes for different users' IP addresses.

The first thing is to check "Enable IP bandwidth control" above, and then you can set it up in detail. When selecting the broadband line type and filling in the bandwidth size, please select and fill in the bandwidth service according to the actual application, and if you are not sure, consult your bandwidth provider (such as China Telecom and Netcom). Such as:

If you are applying for a 5M ADSL, you need to select the line type "ADSL" and set the bandwidth to 5000.

2.Configuration Guidance:

Guaranteed minimum bandwidth (recommended plan): The total bandwidth of the IP addresses (or IP address ranges) that are restricted by this rule can reach at least this value, and the maximum bandwidth can not be limited. This mode maximizes the use of bandwidth resources.

Bandwidth = Total Bandwidth Number of PCs. Assuming that there are five PCs on a 2M ADSL line, the bandwidth available to each computer is 2000 5 = 400kbps. This mode allows the computer to obtain at least 400kbps of bandwidth when the road is busy, which reflects the principle of fairness; **When the road is idle, the bandwidth can be fully utilized, which reflects the principle of reasonableness.

3.In addition, each computer can be set to a fixed IP and bound to the MAC, which can prevent users from modifying the IP without authorization, and can also prevent network ARP attacks, so that the network operation is more stable. If you want to set the computer IP, you need to fill in the DNS, in general, this DNS is taken from:

Running status in the router - DNS in the > WAN port status.

, set the maximum downlink bandwidth to 280.

Of course, IP bandwidth control is bound to IP.

Generally, there are 2 control methods, one is the average score of each IP, that is, 20M is divided into 5 computers, and each IP is divided into 4M (mobile phone IP and computer IP are combined into 4M), which means that no matter how many people are in, they can use the minimum 4M

One is that a certain IP is limited to the maximum and minimum, which is more flexible, and when no one uses it, the maximum can be up to 20M

There are 5 computers, as well as mobile phones.

1 Mbit/s = 1024 Kbps (carriers may use 1 Mbps = 1000 Kbps as early as possible, so the bandwidth may be small).

The above calculations are theoretical values, and the actual number of grasshoppers may affect the speed due to line loss and other material grinding reasons.