What s the deal with the packer not sending the belt?

If the tape is stuck in the middle of the roller and cannot be operated, or there is a foreign object plugged and cannot be taken out, resulting in the cassette, then the technician or operator needs to disassemble the washer of the hexagon nut and loosen the two M5 countersunk screws on the middle connecting shaft.

Since these two screws are fixed in the notched part of the connecting shaft, the screws must be turned up; Remove the connecting shaft, pick up the upper engine, take out the stuck objects, and then restore the machine to its original appearance.

For some common faults on the baler equipment, it is inevitable that the baler will not send the belt, so for this common situation, will you solve it well? 1.The potentiometer with length control of the baler feeds the length control in the zero position, and the length control potentiometer is the second position from the left on the front panel switchboard.

If the clockwise direction is adjusted, the length of the belt is long, and vice versa; If it is in the zero position, it will not be out of the belt. 2.Incorrect straps.

Open the right door and wear the strap correctly according to the "threading process method" or the threading diagram indicated in the manual. 3.There are foreign objects in the upper and lower extensions.

The packaging machine has been used for a long time, and it has not been cleaned and maintained in time, resulting in the accumulation of stolen goods in the machine, so that the feeding belt is not smooth and free, and more cleaning and maintenance should be done. 4.Incorrect gap between the feed rollers.

The size of the gap between the belt feeding rollers of a pair of semi-automatic balers is very important for normal belt feeding, and the adjustment of the gap refers to the instructions in the manual. Adjust carefully until the gap between the feed rollers is only more than the thickness of the tape. 5.

The PP tape used is too thick or too thin. Because there are many manufacturers of PP packing belts, the thickness is also inconsistent, and it should be selected according to the requirements; If this is not possible, please carefully adjust the gap between the return and return rollers according to the method in the manual. 6.

The electromagnet is not working properly. The electromagnet does not work. First check whether the welding head of the electromagnet wire falls off, and then check whether the coil is burned out.

If there is no abnormality in both, check whether the electromagnet is displaced, or if it is blocked by stolen goods, so that the bullet cannot move freely.

A baler is also known as a strapping machine, a taping machine, or a strapping machine. After customers inquire about different baler manufacturers in the market, they will have such questions, why is there such a big difference in balers? This is not because some manufacturers have high profits and some have low profits, most of which is due to different production costs.

Jiahe Machinery is located in Qufu, a famous cultural city with a long history and the hometown of Confucius. It is a machinery company integrating R&D, manufacturing and marketing, welcome your inquiry!

The baler is not working on the knob.

About your question for you to answer: the baler does not send the reason for the baler to summarize the baler belongs to a strapping equipment with a high failure rate, because of the particularity of the working environment, and the packaging materials used can easily lead to the work can not be carried out smoothly, sometimes there will be various production problems, the most common is that the baler can not be sent smoothly. When encountering this kind of problem, customers who have no maintenance experience will have a headache, and the following is a summary of the reasons why the automatic packing machine can not be sent smoothly and the corresponding solutions.

1.The control potentiometer of the belt length of the automatic baler is in the zero position. Workaround:

When there is a problem, the first thing to check the parameter settings of the strapping machine is the first response to the failure, and the staff needs to adjust the potentiometer in the clockwise direction, and the length of the belt will become longer. If you rotate it counterclockwise, the length of the tape will be shortened, and the tape will not be fed if it is in the zero position. 2.

Wrong method of lacing. Solution: The correct way to wear the strap is to open the right door of the baler and re-wear the strap according to the instructions in the manual.

3.There are foreign objects in the upper and lower extensions. Workaround:

The working environment of the automatic baler is generally dirty, and the waste chips of the surrounding packaging materials can be drilled into the gaps of the parts of the baler at any time, so that the machine does not run smoothly, so it is necessary to clean and maintain the strapping machine regularly. 4.Incorrect gap between the feed rollers.

Solution: The gap of the belt feeding roller of the baler directly determines whether the belt feeding work can be completed normally, and it should be adjusted according to the manual, and the gap can be thicker than the packing belt. 5.

The thickness of the packaging material selected by the baler is not standard. Solution: There are many manufacturers of packaging materials, resulting in the quality of the belt is also uneven, the thickness of most packaging materials is within the range of industry standards, it is best to consult the opinions of the packaging machine manufacturer when purchasing the packing belt, in order to ensure that the selected belt can use this strapping machine.

Alternatively, adjust the roller clearance again depending on the belt thickness. 6.The electromagnet is working incorrectly.

Solution: If the electromagnet cannot work normally, it will also cause the baler to fail to feed the belt smoothly, so it is necessary to check whether the welding head of the electromagnet connection is falling off, whether the coil is burned out, and whether the electromagnet is displaced or blocked, causing the bullet to be unable to move normally, and eliminate obstacles according to the actual situation.

Summary. Kiss, the reasons are as follows: 1. The lever tension spring force is too small.

2. The position of the ejector rod is too high, in the case of non-retreat, the gap between the ejector rod and the lever should be retained, if the ejector rod is always on the lever because of improper adjustment, and the jacking force is larger, it will cause the phenomenon that the belt is not in place.

3. The amount of belt in the belt bin is small, and there is no sufficient amount of belt in the belt warehouse, which is easy to produce inadequate belt feeding.

4. If the pre-feeding belt mechanism is not properly adjusted, the storage capacity should be appropriately adjusted.

5. The storage capacity is small due to the failure of the pre-feeding belt mechanism or the problem of the belt bin.

What is the reason why the automatic baler does not take the belt.

Kiss, the reasons are as follows: 1. The lever tension spring force is too small. 2. The position of the ejector rod is too high, in the case of non-retreat, the gap between the ejector rod and the lever should be retained, if the ejector rod is always on the lever because of improper adjustment, and the jacking force is larger, it will cause the phenomenon that the belt is not in place.

3. The amount of belt in the belt bin is small, and there is no sufficient amount of belt in the belt warehouse, which is easy to produce inadequate belt feeding. 4. If the pre-feeding belt mechanism is not properly adjusted, the storage capacity should be appropriately adjusted. 5. The storage capacity is small due to the failure of the pre-feeding belt mechanism or the problem of the belt bin.

Solution: 1. The roller pressure can be adjusted appropriately. 2. Only need to properly adjust the binding force to eliminate the situation that the belt is not in place.

3. The pressure belt plate should be appropriately raised. 4. The top knife should be fixed firmly after adjustment or disassembly. 5. Manual feeding, if the manual feeding is smoother, check the other part.

It is not a retraction. It's not that I don't send it.

Reasons for not retracting: 1. Sensor failure. Users who are familiar with the baler know that at present, the principle used by our domestic baler is cam structure, which is controlled by a main motor to rotate, and the cam will be detected by a corresponding sensor every time it turns to a position, so if the sensor fails, the machine cannot receive the signal that needs to cut the tape, and naturally it cannot cut the tape.

2. The compression spring of the middle top knife is broken. The function of the top knife is to jack up the strap to cut and glue, but if the top knife cannot be jacked to the specified position for other reasons, then the baler can not cut the belt well. 3. The tension spring of the middle top knife is broken.

In addition to the internal compression spring, the middle top knife also has an external tension spring, which plays the role of fixing the three knives together, and if the tension spring is broken, it cannot be cut.

1.The strapping of the automatic baler is not tight, so check the basic tightness adjustment device first, the device is too loose, and the strapping will not be tight. 2.

The cassette device of the baler is too worn, which will also cause the strapping to be not tight. 3.The cogging of the cassette device has foreign matter or chips, which is also the main reason for the lack of strapping.

4.Check whether the tie rod spring of the lower baler is broken. 5.

Check whether the sway rod push bearing of the automatic baler has cracked. 6.The torsion spring of the automatic baler will also cause the strap to be loosely bundled.

The strapping machine strap does not adhere to the main pants is caused by the following problems.

1.The ironing head is positioned too high or too low and does not reach between the two straps, so you can use pliers.

Directly adjust the height of the ironing head to solve the problem of high fiber.

2.If the temperature of the hot head is too high or too low, it can lead to stickiness, and then it will fall apart after being packed and bundled. We need to adjust the temperature to solve it.

3.The tension spring on the ironing head is tired and does not extend the ironing head into place.

4.The upper slide plate and the middle knife are not tightened, which will cause the sticky to not be firm, the lower bearing of the middle knife will be damaged, or the slide plate will not be set back into place. (Look for traces of the middle knife on the slide board.) ）

5.The perm is not too hot or not hot.

The soft connection cable under the hot head is loose and aging. We simply treat the oxidized surface, and it is ready to use. If the perm has no temperature at all, it is cold, it may be that the safety on the computer board is burned, or the large transformer is broken.

6.The quality of the packing belt is too poor.

The strapper does not come out of the packing belt, the strapping machine will have a cassette problem, the strap is stuck in the middle of the roller, or there are foreign objects plugged to cause the cassette. should nuts for washers. Loosen the countersunk screw on the middle connecting shaft, remove the connecting shaft, pick up the upper engine, and take out the stuck object.

Secondly, the baler does not cut the belt. The slippery belt is oily and must be removed to wipe off the oil. If the belt is too tight, lower the belt drive seat or retract the motor.

Automated balers sometimes have some problems, such as not automatically feeding the tape. First check whether the potentiometer of the belt length control is in the zero position, the belt length control potentiometer is in the second position from the left on the front panel switch plate, if it is in the zero position, it will not be out of the belt. Incorrect belt will also cause not to be belted, packaging machine long-term use, and failure to clean and maintain in time, resulting in the accumulation of stolen goods in the machine, so that the belt is not smooth and free, will also cause not to be belted, the machine can be comprehensively cleaned Shenzhen wheat field packaging machine They can also deal with it, I hope it can help you.

Summary. The first thing to suspect is that the LS1 switch on the right side of the upper skateboard is damaged or the shrapnel is blocked by a foreign object, and the contact cannot be touched, and the solution is to replace the LS1 switch or take out the foreign body.

If the automatic baler does not stop working continuously, it is necessary to check whether the LS5 switch is normal, and if it is not damaged, check whether there is any stolen goods stuck between the contact and the shrapnel, so that the contact cannot be opened normally after inserting the belt. Another possible reason is that when the LS5 switch is zeroed, the contact is not closed, so the power supply continues to work continuously as soon as it is turned on.

If the strap is cut off by the automatic strapping machine before it is tightly tied, you should readjust the tightness, and then check whether the LS3 and LS5 switches are faulty.

The packer plug strap didn't respond, what's going on.

The first thing to suspect is that the LS1 switch on the right side of the upper slide plate is damaged or the shrapnel is blocked by a foreign object, and the solution is to replace the LS1 switch or take out the foreign body. If the automatic baler does not stop when working continuously, it is necessary to check whether the LS5 switch is normal, and if it is not damaged, check whether there is any stolen goods stuck between the contact and the shrapnel, so that the contact cannot be opened normally after inserting the belt. Another possible reason is that when the LS5 switch is zeroed, the contact is not closed, so the power supply continues to work continuously as soon as it is turned on.

If the strap is cut off by the automatic strapping machine before it is tightly tied, you should readjust the tightness, and then check whether the LS3 and LS5 switches are faulty.

LS1 is good! A manual reset will work! It's just that touching ls1 doesn't respond and doesn't work.

Is there a shrapnel?

Hello, the above questions will be answered by me. If the packing belt of the baler is not tightened, you can try the following methods: 1. Try it for a roll of packing belt, generally speaking, the requirements of the automatic packing machine for the packing belt are relatively high, and it may be due to the problem of filial piety when tightening the belt due to the wrong packing belt for you.

Second, to check whether the belt rail is loose, the general situation is that the nut is loose, if the belt slides out to the side and cannot reach the standard position, it is the belt rail is loose. 3. Cassette, due to improper operation or unsatisfactory tape, will cause the tape to be stuck in the belt feeding rail. This requires removing the tape plate next to the belt feeding rail, then pulling out the strap that is stuck inside, and then using compressed air to remove the remaining part of the strap inside.

I hope to help you!